DataSheet.jp

FAN2535 の電気的特性と機能

FAN2535のメーカーはFairchild Semiconductorです、この部品の機能は「(FAN2534 / FAN2535) 150 mA CMOS LDO Regulator」です。


製品の詳細 ( Datasheet PDF )

部品番号 FAN2535
部品説明 (FAN2534 / FAN2535) 150 mA CMOS LDO Regulator
メーカ Fairchild Semiconductor
ロゴ Fairchild Semiconductor ロゴ 




このページの下部にプレビューとFAN2535ダウンロード(pdfファイル)リンクがあります。

Total 11 pages

No Preview Available !

FAN2535 Datasheet, FAN2535 PDF,ピン配置, 機能
www.DataSheet4U.com
www.fairchildsemi.com
FAN2534/FAN2535
150 mA CMOS LDO Regulator with Fast Start, Enable
Features
• 70dB Ripple rejection ( >45dB up to 1MHz)
• 150µsec Power On Time
• 150µsec Enable Time
• Low noise - 50µVrms
• Enable optimized for CDMA time slices
• 180 mV dropout voltage at 150 mA
• Enable/Shutdown Control
• Enable time independent of noise bypass capacitor value
• SOT23-5 package
• Thermal limiting
• 300 mA trimmed current limit
Applications
• Cellular Phones and accessories
• PDAs
• Portable cameras and video recorders
• Laptop, notebook and palmtop computers
Description
The FAN2534/FAN2535 family of micropower low-dropout
voltage regulators utilize CMOS technology to offer a new
level of cost-effective performance in GSM, TDMA, and
CDMA cellular handsets, laptop and notebook computers,
and other portable devices. Proprietary design technics
ensure high ripple rejection. Other features include low
noise, short circuit current limit, thermal shutdown circuit,
low dropout voltage, fast enable required in CDMA handset
applications, exceptional loop stability to accommodate a
wide variety of external capacitors, and a compact SOT23-5
surface-mount package. These products offer significant
improvements over older Bipolar and CMOS designs and are
pin-compatible with many popular devices.
The FAN2534 and FAN2535 devices are distinguished by
the assignment of pin 4:
FAN2534: pin 4 – ADJ, allowing the user to adjust the
output voltage over a wide range using an external voltage
divider.
FAN2534-XX: pin 4 – BYP, to which a bypass capacitor
may be connected for optimal noise performance. Output
voltage is fixed, as specified by the suffix XX.
FAN2535-XX: pin 4 – ERR, a flag which indicates that the
output voltage has dropped below the specified minimum
due to a fault condition.
The standard fixed output voltages available are 2.6V, 2.85V,
and 3.0V . Custom output voltages are also available: please
contact your local Fairchild Sales Office for information.
Block Diagrams
VIN
Bandgap
FAN2534
EN
Error
p
Amplifier
VOUT
Thermal
Sense
ADJ
GND
VIN
Bandgap
EN
Error
Amplifier
p
Thermal
Sense
FAN2534-XX
BYP
VIN
Bandgap
VOUT
EN
Error
Amplifier
p
ERR
VOUT
GND
Thermal
Sense
FAN2535-XX
GND
REV. 1.0.2 8/26/03

1 Page





FAN2535 pdf, ピン配列
PRODUCT SPECIFICATION
www.DataSheet4U.com
Operating Conditions
Symbol
VIN
VOUT
VOUT
VEN
VERR
TJ
θJA
θJC
Parameter
Input Voltage Range
Output Voltage Range
FAN2534-XX, FAN2535-XX (Note 3)
Output Voltage Range (FAN2534 only)
Enable Input Voltage
ERR Flag Voltage
Junction Temperature
Thermal resistance
Thermal resistance
DC Electrical Characteristics (Notes 4, 5)
Symbol
Parameter
Regulator
VDO Drop Out Voltage (Note 6)
VO Output Voltage Accuracy
(Note 7)
IGND(NL) Ground Pin Current
IGND(FL) Ground Pin Current
Protection
Current Limit
IGSD
TSH
Shut-Down Current
Thermal Shutdown
Temperature
Hysteresis
ETL ERR Trip Level
Enable Input
VEL Logic Low Voltage
VEH Logic High Voltage
IEH Input Current High
IEL Input Current Low
Conditions
IOUT = 100 µA
IOUT = 50 mA
IOUT = 100 mA
IOUT = 150 mA
Initial Accuracy at no
load
Over Line, Load &
Temp
No Load
IOUT = 150 mA
EN = 0V
FAN2535 only
Min.
VOUT+VDO
2.3
Typ.
2.0
0
-40
220
130
Min.
-1
-3.7
90
1.4
Typ.
2.5
50
100
180
90
110
300
155
15
93
0.4
2
FAN2534/FAN2535
Max.
6.5
3.3
5.0
VIN
VIN
+125
Units
V
V
V
V
V
°C
°C/W
°C/W
Max.
Units
4 mV
75 mV
140 mV
220 mV
1%
2%
µA
µA
400 mA
1 µA
°C
°C
96 %
1.2 V
V
1 µA
1 µA
REV. 1.0.2 8/26/03
3


3Pages


FAN2535 電子部品, 半導体
FAN2534/FAN2535
www.DataSheet4U.com
Control Functions
Enable Pin
Connecting 2.0V or greater to the Enable pin will enable the
output, while 0.4V or less will disable it while reducing the
quiescent current consumption to less than 1µA. If this
shutdown function is not needed, the pin can simply be
connected permanently to the VIN pin. Allowing this pin
to float will cause erratic operation.
Error Flag (FAN2535-XX Only)
Fault conditions such as input voltage dropout
(low VIN), overheating, or overloading (excessive output
current), will set an error flag: The ERR pin which is an
open-drain output, will go LOW when VOUT is less than
95% or the specified output voltage. When the voltage at
VOUT is greater than 95% of the specified output voltage,
the ERR pin is HIGH. A logic pullup resistor of 100K Ohm
is recommended at this output. The pin can be left discon-
nected if unused.
Thermal Protection
The FAN2534/FAN2535 is designed to supply high peak
output currents for brief periods, however sustained exces-
sive output load at high input - output voltage difference
will cause the device temperature to increase and exceed
maximum ratings due to power dissipation. During output
overload conditions, when the die temperature exceeds the
shutdown limit temperature of 155°C, an onboard thermal
protection will disable the output until the temperature drops
approximately 15°C below the limit, at which point the
output is re-enabled. During a thermal shutdown situation
the user may assert the power-down function at the Enable
pin, reducing power consumption to a minimum.
Thermal Characteristics
The FAN2534/FAN2535 is designed to supply 150mA at
the specified output voltage with an operating die (junction)
temperature of up to 125°C. Once the power dissipation and
thermal resistance is known, the maximum junction tempera-
ture of the device can be calculated. While the power dissipa-
tion is calculated from known electrical parameters, the
actual thermal resistance depends on the thermal characteris-
tics of the SOT23-5 surface-mount package and the
surrounding PC Board copper to which it is mounted.
The power dissipation is equal to the product of the input-to-
output voltage differential and the output current plus the
ground current multiplied by the input voltage, or:
PD = (VIN – VOUT)IOUT + VINIGND
PRODUCT SPECIFICATION
The relationship describing the thermal behavior of the
package is:
PD(max)
=
T----J---(-m----θa---xJ---A)---–----T----A--
where TJ(max) is the maximum allowable junction tempera-
ture of the die, which is 125°C, and TA is the ambient operat-
ing temperature. θJA is dependent on the surrounding PC
board layout and can be empirically obtained. While the θJC
(junction-to-case) of the SOT23-5 package is specified at
130°C /W, the θJA of the minimum PWB footprint will be at
least 235°C /W. This can be improved upon by providing a
heat sink of surrounding copper ground on the PWB.
Depending on the size of the copper area, the resulting θJA
can range from approximately 180°C /W for one square inch
to nearly 130°C /W for 4 square inches. The addition of
backside copper with through-holes, stiffeners, and other
enhancements can also aid in reducing thermal resistance.
The heat contributed by the dissipation of other devices
located nearby must be included in the design consider-
ations. Once the limiting parameters in these two relation-
ships have been determined, the design can be modified to
ensure that the device remains within specified operating
conditions. If overload conditions are not considered, it is
possible for the device to enter a thermal cycling loop, in
which the circuit enters a shutdown condition, cools, re-
enables, and then again overheats and shuts down repeatedly
due to an unmanaged fault condition.
Adjustable Version
The FAN2534 adjustable version includes an input pin ADJ
which allows the user to select an output voltage ranging
from 2.5V to near VIN, using an external resistor divider. The
voltage VADJ presented to the ADJ pin is fed to the onboard
error amplifier which adjusts the output voltage until VADJ is
equal to the onboard bandgap reference voltage of
1.00V(typ). The equation is:
VOUT = 1.00V × 1 + -RR----ul-o-p--w-p---ee--rr
Since the bandgap reference voltage is trimmed, 1% initial
accuracy can be achieved. The total value of the resistor
chain should not exceed 250K Ohm total to keep the error
amplifier biased during no-load conditions. Programming
output voltages very near VIN need to allow for the magni-
tude and variation of the dropout voltage VDO over load,
supply, and temperature variations. Note that the low-leak-
age FET input to the CMOS Error Amplifier induces no bias
current error to the calculation.
The ground pin current IGND can be found in the charts
provided in the Electrical Characteristics section.
6 REV. 1.0.2 8/26/03

6 Page



ページ 合計 : 11 ページ
 
PDF
ダウンロード
[ FAN2535 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
FAN2534

(FAN2534 / FAN2535) 150 mA CMOS LDO Regulator

Fairchild Semiconductor
Fairchild Semiconductor
FAN2535

(FAN2534 / FAN2535) 150 mA CMOS LDO Regulator

Fairchild Semiconductor
Fairchild Semiconductor


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap