|
|
PDF ISL28136 Data sheet ( Hoja de datos )
| Número de pieza | ISL28136 | |
| Descripción | (ISL28136 / ISL28236) Single and Dual Precision Rail-to-Rail Input-Output (RRIO) Op Amps | |
| Fabricantes | Intersil Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ISL28136 (archivo pdf) en la parte inferior de esta página. Total 15 Páginas | ||
|
No Preview Available !
®
Data Sheet
ISL28136, ISL28236
February 11, 2008
FN6153.3
5MHz, Single and Dual Precision Rail-to-
Rail Input-Output (RRIO) Op Amps
www.TdahteasIhSeLe2t48u1.3c6omand ISL28236 are low-power single and dual
operational amplifiers optimized for single supply operation
from 2.4V to 5.5V, allowing operation from one lithium cell or
two Ni-Cd batteries. These devices feature a gain-bandwidth
product of 5MHz and are unity-gain stable with a -3dB
bandwidth of 13MHz.
These devices feature an Input Range Enhancement Circuit
(IREC), which enables them to maintain CMRR performance
for input voltages greater than the positive supply. The input
signal is capable of swinging 0.25V above the positive
supply and to the negative supply with only a slight
degradation of the CMRR performance. The output
operation is rail-to-rail.
The parts typically draw less than 1mA supply current per
amplifier while meeting excellent DC accuracy, AC
performance, noise and output drive specifications.
Operation is guaranteed over -40°C to +125°C temperature
range.
Ordering Information
PART
NUMBER
(Note)
PART
MARKING
PACKAGE
(Pb-Free)
PKG.
DWG. #
ISL28136FHZ-T7* GABP
6 Ld SOT-23 MDP0038
ISL28136FHZ-T7A* GABP
6 Ld SOT-23 MDP0038
ISL28136FBZ
28136 FBZ 8 Ld SOIC
MDP0027
ISL28136FBZ-T7* 28136 FBZ 8 Ld SOIC
MDP0027
Coming Soon
ISL28236FBZ
28236 FBZ 8 Ld SOIC
MDP0027
Coming Soon
ISL28236FBZ-T7*
28236 FBZ 8 Ld SOIC
MDP0027
Coming Soon
ISL28236FUZ
8236Z
8 Ld MSOP
MDP0043
Coming Soon
ISL28236FUZ-T7*
8236Z
8 Ld MSOP
MDP0043
*Please refer to TB347 for details on reel specifications.
NOTE: These Intersil Pb-free plastic packaged products employ
special Pb-free material sets; molding compounds/die attach
materials and 100% matte tin plate PLUS ANNEAL - e3 termination
finish, which is RoHS compliant and compatible with both SnPb and
Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed
the Pb-free requirements of IPC/JEDEC J STD-020.
Features
• 5MHz Gain bandwidth product @ AV = 100
• 13MHz -3db unity gain bandwidth
• 900µA typical supply current (per amplifier)
• 150µV maximum offset voltage (8 Ld SOIC)
• 16nA typical input bias current
• Down to 2.4V single supply voltage range
• Rail-to-rail input and output
• Enable pin (ISL28136 only)
• -40°C to +125°C operation
• Pb-free (RoHS compliant)
Applications
• Low-end audio
• 4mA to 20mA current loops
• Medical devices
• Sensor amplifiers
• ADC buffers
• DAC output amplifiers
Pinouts
ISL28136
(6 LD SOT-23)
TOP VIEW
ISL28136
(8 LD SOIC)
TOP VIEW
OUT 1
6 V+
NC 1
8 EN
V- 2
IN+ 3
+-
5 EN
4 IN-
IN- 2
IN+ 3
-
+
7 V+
6 OUT
V- 4
5 NC
ISL28236
(8 LD SOIC)
TOP VIEW
ISL28236
(8 LD MSOP)
TOP VIEW
OUT_A 1
8 V+
OUT_A 1
8 V+
IN-_A 2
IN+_A 3
V- 4
-+
+-
7 OUT_B
6 IN-_B
5 IN+_B
IN-_A 2
IN+_A 3
V- 4
-+
+-
7 OUT_B
6 IN-_B
5 IN+_B
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2007, 2008. All Rights Reserved.
All other trademarks mentioned are the property of their respective owners.
1 page  
ISL28136, ISL28236
Typical Performance Curves V+ = 5V, V- = 0V, VCM = 2.5V, RL = Open (Continued)
1
0
-1
-2
-3
www.datash-e4et4u.com
-5
-6 RL = 10k
-7
CL = 16.3pF
AV = +1
-8 VOUT = 10mVP-P
-9
10k
100k
V+ = 5V
V+ = 2.4V
1M 10M
FREQUENCY (Hz)
100M
8
7
6
5
4
3
2
1
0
-1
-2
-3 V+ = 5V
-4 RL = 1k
-5
-6
-7
AV = +1
VOUT = 10mVP-P
-8
10k 100k
CL = 51.7pF
CL = 43.7pF
CL = 37.7pF
CL = 26.7pF
CL = 16.7pF
CL = 4.7pF
1M
FREQUENCY (Hz)
10M
FIGURE 7. GAIN vs FREQUENCY vs SUPPLY VOLTAGE
FIGURE 8. GAIN vs FREQUENCY vs CL
100M
20
0
-20
-40
V+ = 2.4V, 5V
-60 RL = 1k
CL = 16.3pF
-80 AV = +1
VCM = 1VP-P
-100
10
100
1k
10k 100k 1M
10M
FREQUENCY (Hz)
FIGURE 9. CMRR vs FREQUENCY; V+ = 2.4V AND 5V
20
V+, V- = ±1.2V
0 RL = 1k
CL = 16.3pF
-20 AV = +1
-40 VSOURCE = 1VP-P
-60
PSRR-
PSRR+
-80
-100
-120
10
100
1k
10k 100k 1M
10M
FREQUENCY (Hz)
FIGURE 10. PSRR vs FREQUENCY, V+, V- = ±1.2V
20
V+, V- = ±2.5V
0 RL = 1k
CL = 16.3pF
-20 AV = +1
-40 VSOURCE = 1VP-P
PSRR-
-60
PSRR+
-80
-100
-120
10
100
1k
10k 100k 1M
10M
FREQUENCY (Hz)
FIGURE 11. PSRR vs FREQUENCY, V+, V- = ±2.5V
100
V+ = 5V
RL = 1k
CL = 16.3pF
AV = +1
10
1 10 100 1k 10k 100k
FREQUENCY (Hz)
FIGURE 12. INPUT VOLTAGE NOISE DENSITY vs FREQUENCY
5 FN6153.3
February 11, 2008
5 Page 
ISL28136, ISL28236
Applications Information
Introduction
The ISL28136 and ISL28236 are single and dual channel
Bi-CMOS rail-to-rail input, output (RRIO) micropower
precision operational amplifiers. The parts are designed to
operate from single supply (2.4V to 5.5V) or dual supply
www.(d±a1ta.2shVeetot4±u2.c.o7m5V). The parts have an input common mode
range that extends 0.25V above the positive rail and down to
the negative supply rail. The output operation can swing
within about 3mV of the supply rails with a 100kΩ load.
Rail-to-Rail Input
Many rail-to-rail input stages use two differential input pairs,
a long-tail PNP (or PFET) and an NPN (or NFET). Severe
penalties have to be paid for this circuit topology. As the
input signal moves from one supply rail to another, the
operational amplifier switches from one input pair to the
other causing drastic changes in input offset voltage and an
undesired change in magnitude and polarity of input offset
current.
The ISL28136 and ISL28236 achieve input rail-to-rail
operation without sacrificing important precision
specifications and degrading distortion performance. The
devices’ input offset voltage exhibits a smooth behavior
throughout the entire common-mode input range. The input
bias current versus the common-mode voltage range gives
an undistorted behavior from typically down to the negative
rail to 0.25V higher than the positive rail.
Rail-to-Rail Output
A pair of complementary bi-polar devices are used to
achieve the rail-to-rail output swing. The PNP sinks current
to swing the output in the negative direction. The NPN
sources current to swing the output in the positive direction.
The ISL28136 and ISL28236 with a 100kΩ load will swing to
within 3mV of the positive supply rail and within 3mV of the
negative supply rail.
Results of Over-Driving the Output
Caution should be used when over-driving the output for long
periods of time. Over-driving the output can occur in two ways.
1) The input voltage times the gain of the amplifier exceeds the
supply voltage by a large value or, 2) the output current
required is higher than the output stage can deliver. These
conditions can result in a shift in the Input Offset Voltage (VOS)
as much as 1µV/hr. of exposure under these conditions.
IN+ and IN- Input Protection
All input terminals have internal ESD protection diodes to both
positive and negative supply rails, limiting the input voltage to
within one diode beyond the supply rails. They also contain
back-to-back diodes across the input terminals (see “Pin
Descriptions” on page 10 - Circuit 1). For applications where
the input differential voltage is expected to exceed 0.5V, an
external series resistor must be used to ensure the input
currents never exceed 5mA (Figure 38).
-
RIN
VIN +
RL
VOUT
FIGURE 38. INPUT CURRENT LIMITING
Enable/Disable Feature
The ISL28136 offers an EN pin that disables the device
when pulled up to at least 2.0V. In the disabled state (output
in a high impedance state), the part consumes typically 10µA
at room temperature. The EN pin has an internal pull-down.
If left open, the EN pin will pull to the negative rail and the
device will be enabled by default. The EN pin should never
be left floating. When not used, the EN pin should either be
left floating or connected to the V- pin.
By disabling the part, multiple ISL28136 parts can be
connected together as a MUX. In this configuration, the
outputs are tied together in parallel and a channel can be
selected by the EN pin. The loading effects of the feedback
resistors of the disabled amplifier must be considered when
multiple amplifier outputs are connected together. Note that
feed through from the IN+ to IN- pins occurs on any Mux
Amp disabled channel where the input differential voltage
exceeds 0.5V (e.g., active channel VOUT = 1V, while
disabled channel VIN = GND), so the mux implementation is
best suited for small signal applications. If large signals are
required, use series IN+ resistors, or a large value RF, to
keep the feed through current low enough to minimize the
impact on the active channel. See“Limitations of the
Differential Input Protection” on page 11 for more details.
Limitations of the Differential Input Protection
If the input differential voltage is expected to exceed 0.5V, an
external current limiting resistor must be used to ensure the
input current never exceeds 5mA. For non-inverting unity gain
applications, the current limiting can be via a series IN+ resistor,
or via a feedback resistor of appropriate value. For other gain
configurations, the series IN+ resistor is the best choice, unless
the feedback (RF) and gain setting (RG) resistors are both
sufficiently large to limit the input current to 5mA.
Large differential input voltages can arise from several
sources:
1) During open loop (comparator) operation. Used this way,
the IN+ and IN- voltages don’t track, so differentials arise.
2) When the amplifier is disabled but an input signal is still
present. An RL or RG to GND keeps the IN- at GND, while
the varying IN+ signal creates a differential voltage. Mux
Amp applications are similar, except that the active channel
VOUT determines the voltage on the IN- terminal.
11 FN6153.3
February 11, 2008
11 Page | ||
| Páginas | Total 15 Páginas | |
| PDF Descargar | [ Datasheet ISL28136.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ISL28130 | (ISL28x30) RRIO Operational Amplifiers |  Intersil |
| ISL28133 | (ISL28x33) RRIO Operational Amplifiers | Intersil Corporation |
| ISL28134 | Zero Drift Rail-to-Rail Precision Op Amp | Intersil |
| ISL28136 | (ISL28136 / ISL28236) Single and Dual Precision Rail-to-Rail Input-Output (RRIO) Op Amps | Intersil Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |