|
|
D5F-2B10のメーカーはOmronです、この部品の機能は「High Precision Optical Switch」です。 |
部品番号 | D5F-2B10 |
| |
部品説明 | High Precision Optical Switch | ||
メーカ | Omron | ||
ロゴ | |||
このページの下部にプレビューとD5F-2B10ダウンロード(pdfファイル)リンクがあります。 Total 6 pages
High-precision Optical Switch
Optical System Achieves 1-mm
Operating Position Repeatability in this
4-way Switch
■ A knife-edge mechanism in the optical system
provides greater precision for a more stable out-
put without faulty contact operation.
■ Reduced size and weight (34 mm at operating
section and 60 g total).
■ Wear-resistive ceramic parts used in the mea-
www.DataSheet4U.csoumrement section.
■ Two different output types available.
D5F
Ordering Information
■ List of Models
Output configuration
PNP open collector
(+ common)
NPN open collector
(– common)
Contact form
SPST-NC
SPST-NO
Operation indicator
ON when not operated
ON when operated
Cable length
1m
3m
1m
3m
Model
D5F-2B10
D5F-2B30
D5F-3C10
D5F-3C30
Specifications
■ Ratings
Power supply voltage
Output current
Power consumption
Leakage current
Residual voltage
12/24 VDC10%, ripple (p–p): 10% max.
100 mA max.
30 mA max.
0.15 mA max.
2 V max.
■ Characteristics
Degree of protection
Life expectancy (see note 2)
Operating speed
Max. operating frequency
Insulation resistance
Dielectric strength
Vibration resistance
Shock resistance
Repeat accuracy
Ambient temperature (see note 4)
Ambient humidity
Weight
IP67
Mechanical: 5,000,000 operations min.
Electrical: 5,000,000 operations min.
1 mm/s to 50 cm/s
60 operations/minute max.
100 MW min. (at 500 VDC) between each terminal and ground
1,100 VAC between each terminal and ground
Malfunction: 10 to 500 Hz, 1.3-mm double amplitude
Malfunction: 300 m/s2 min.
1 mm max. (see note 3)
Operating: –10C to 60C (with no icing)
Operating: 30% to 95%
Switch body: approx. 50 g; Cord: 23 g/m
Note:
1. The above figures are initial values.
2. Life expectancy values are calculated at an operating temperature of 5C to 35C, and an operating humidity of 40% to 70%.
Contact your OMRON sales representative for more detailed information on other operating environments.
3. Measurements were conducted repeatedly at the same point. The value is 1 mm max. for 200 measurements. For other condi-
tions in detail, contact your OMRON sales representative.
4. The ambient operating temperature varies depending on the current. Refer to the following Engineering Data.
280
1 Page D5F
■ Repeat Accuracy (Reference Data)
D5F-2B10
No. 1 ON
No. 2 ON
No. 1 OFF
www.DataSheet4U.com
No. 3 ON
No. 3 OFF
No. 2 OFF
No. 4 ON
No. 4 OFF
D5F
282
3Pages D5F D5F
Precautions
■ Correct Use
Do not impose any force exceeding 29.42 N on the cord, other-
wise the cord may break. Make sure that the bending radius of
the cord is at least 20 mm.
Connections
Take the residual voltage (2 V max.) into consideration when con-
necting a load or power supply.
When the internal circuit of the D5F is open, there will be a leak-
age current of 0.15 mA maximum and a residual voltage on the
load. Check the release voltage of the load before use.
Handling
Do not drop or impose external force, such as shock, on the D5F.
www.DataSheet4OUth.ceormwise, the D5F may malfunction or lose its accuracy.
Operating Environment
The operating environment has a significant effect on the D5F.
Consult your OMRON representative before using the D5F in
environments with different cutting oil, solvent, or gas.
Noise
If the power supply line is affected by excessive noise, the D5F
may lose its accuracy.
Refer to the following and if the noise level is excessively high,
take a proper countermeasure, such as the use of a noise filter.
Level
1 kV p-p
1.5 kV p-p
Influence on accuracy
3 mm max.
5 mm max.
Make sure that the ripple rate of the power supply is 10% maxi-
mum.
Operation
Do not press two or more plungers at the simultaneously, other-
wise the D5F may break.
Example: Two-directional Operation
Incorrect
Precautions
Light Source Burnout
The D5F does not use any contacts. Therefore no contact failures
will result. If the LED light source burns out due to noise or any
other cause, the following will result.
#D5F-2B 0: The output transistor is kept turned OFF.
#D5F-3C 0: The output transistor is kept turned ON.
Take the above into consideration and install a stopper mecha-
nism so that the machine will not be damaged or the Switch will
not be pressed excessively if the output transistor does not oper-
ate properly.
Adhesive Agent
The ceramic chips are glued with epoxy resin that may deteriorate
due to cutting oil or warm solvent. In the worst case, the chips
may fall off. The chips can withstand certain cutting oils or ace-
tone. Check the operating environment before using the D5F.
POHL-Electronic
Neuendorf Straße 18b
16761 Hennigsdorf
www.pohl-electronic.de
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Cat. No. C117-E1-1
285
6 Page | |||
ページ | 合計 : 6 ページ | ||
|
PDF ダウンロード | [ D5F-2B10 データシート.PDF ] |
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
部品番号 | 部品説明 | メーカ |
D5F-2B10 | High Precision Optical Switch | Omron |