|
|
NL10276BC30-04DのメーカーはNECです、この部品の機能は「TFT COLOR LCD MODULE」です。 |
部品番号 | NL10276BC30-04D |
| |
部品説明 | TFT COLOR LCD MODULE | ||
メーカ | NEC | ||
ロゴ | |||
このページの下部にプレビューとNL10276BC30-04Dダウンロード(pdfファイル)リンクがあります。 Total 24 pages
DATA SHEET
TFT COLOR LCD MODULE
NL10276BC30-04D
38 cm (15.0 inches), 1024 × 768 pixels, 262,144 colors,
LVDS interface, high luminance
DESCRIPTION
The NL10276BC30-04D is a TFT (thin film transistor) active-matrix color liquid crystal display (LCD) comprising
an amorphous silicon TFT attached to each signal electrode, a driving circuit, and a backlight. The NL10276BC30-
04D has a built-in backlight. Backlight includes long-life-lamps and the lamps are replaceable with lamp holders.
The 38 cm (15.0 inch) diagonal display area contains 1024 × 768 pixels and can display 262,144 colors
simultaneously.
FEATURES
• LVDS interface (adapted the THC63LVDF64A, Thine Electronics, Inc. as a receiver)
• Wide viewing angle (with Retardation Film)
• High luminance (350 cd/m2 at IL = 6 mArms/lamp)
• Low reflection
• Incorporated edge-type backlight (four lamps/two holders)
• Replaceable lamp holders (part No. 150LHS12)
• Recommended inverter: Part No. 150PW081
APPLICATIONS
• PC monitors
The information in this document is subject to change without notice.
Please confirm the delivery specification before starting to design your system.
Document No. EN0488EJ1V0DS00 (1st edition)
Date Published September 2000 P CP(N)
Printed in Japan
©
2000
1 Page BLOCK DIAGRAM
I/F
LCD module
NL10276BC30-04D
D0+/–
D1+/–
D2+/–
CK+/–
VCC
GND
FG
DC/DC
Converter
Power supply
for drivers
VHIGH1
VHIGH2
VHIGH3
VHIGH4
VLOW2
VLOW1
H-driver
3072 lines
TFT LCD panal
768lines
H: 1024 × 3 (R, G, B)
V: 768
Backlight
(Edge light type)
Note GND is connected to FG (frame ground) in the LCD module. These grounds should be connected in
customer equipment.
Data Sheet EN0488EJ1V0DS00
3
3Pages NL10276BC30-04D
SUPPLY VOLTAGE SEQUENCE
VCC
0V
4.75 V
tr < 80 ms
Signals Note 1
0V
Valid peiod
0.5 V
t > 200 ms
10 < t < 35 ms
0 < t < 35 ms
Note: 1 Terminations of the signal lines are resistance 100 Ω.
Remark: 1. Logic signals (synchronous signals and control signals) must be “0” voltage (V), when VCC is not
input. If input voltage to signal lines is higher than 0.3 V, the internal circuit will be damaged.
2. The supply voltage for input signals should be the same as VCC.
3. Turn on the backlight within the LCD operation period. When the backlight turns on before LCD
operation or the LCD operation turns off before the backlight turns off, the display may
momentarily become white.
4. When the power is off, please keep whole signals at low level or high impedance.
5.ý This LCD module uses a fuse as follows.
Fuse
Type name
VCC ICP-S1.2
Producer
Rohm
Rating
50 V/1.2 A
Before the power supply for the module is designed, a fuse protection should be considered. The
power supply should be use more than 2.0 times of the fuse rating. In case of small power
capacity, the module should be evaluate enough.
6 Data Sheet EN0488EJ1V0DS00
6 Page | |||
ページ | 合計 : 24 ページ | ||
|
PDF ダウンロード | [ NL10276BC30-04D データシート.PDF ] |
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
部品番号 | 部品説明 | メーカ |
NL10276BC30-04 | TFT COLOR LCD MODULE | NEC |
NL10276BC30-04D | TFT COLOR LCD MODULE | NEC |
NL10276BC30-04F | TFT COLOR LCD MODULE | NEC |