DataSheet.jp

FM-TX2-XXX の電気的特性と機能

FM-TX2-XXXのメーカーはrfsolutionsです、この部品の機能は「FM TRANSMITTER & RECEIVER MODULES」です。


製品の詳細 ( Datasheet PDF )

部品番号 FM-TX2-XXX
部品説明 FM TRANSMITTER & RECEIVER MODULES
メーカ rfsolutions
ロゴ rfsolutions ロゴ 




このページの下部にプレビューとFM-TX2-XXXダウンロード(pdfファイル)リンクがあります。
Total 9 pages

No Preview Available !

FM-TX2-XXX Datasheet, FM-TX2-XXX PDF,ピン配置, 機能
FM TRANSMITTER & RECEIVER
MODULES. (2ND GENERATION)
FEATURES
MINIATURE PACKAGE
PLUG IN COMPATIBLE WITH FM-TX1 / RX1
EMC CONFORMANT TO ETS 300-683
TYPE APPROVED TO ETS 300-220
DATA RATES TO 40KBIT/S
www.DataSheet4U.coUmSABLE RANGE TO 300 METRES
418 & 433.92MHZ VERSIONS.
SINGLE SUPPLY VOLTAGE 5V OR 3V
FULLY SCREENED
FM-TX2-XXX
FM-RX2-XXX
Transmitter - TX2
2 STAGE SAW CONTROLLED, FM
MODULATED AT UPTO 40KBIT/S
OPERATION FROM 2.2 TO 6 VOLTS
10mW ON 433.92MHZ (EUROPE) , 1mW ON
418MHZ (UK)
HIGH EFFICIENCY, >15% , DC --> RF
IMPROVED FREQUENCY AND DEVIATION
ACCURACY
2ND HARMONIC, < -60DBC
Receiver - RX2
DOUBLE CONVERSION FM SUPERHET
SAW FRONT END FILTER, IMAGE
REJECTION 50DB
SUPPLY 3.0 TO 6.0 VOLTS @ 13MA
40KBIT/S, -F VERSION , -100 DBM
SENSITIVITY @ 1PPM BER
14KBIT/S. -A VERSION , -107 DBm
SENSITIVITY @ 1PPM BER
LO LEAKAGE, < -60 DBM
Description
The TX2 and RX2 data link modules are a miniature PCB mounting UHF radio transmitter and receiver pair
which enable the simple implementation of a data link at upto 40 Kbit/s at distances upto 75 metres in-building
and 300 metres open ground.
Available for operation at 433.92 MHz in Europe and 418.00 MHz in the U.K., both modules combine full
screening with extensive internal filtering to ensure EMC compliance by minimising spurious radiations and
susceptibilities. The TX2 and RX2 modules will suit one-to-one and multi-node wireless links in applications
including car and building security, EPOS and inventory tracking, remote industrial process monitoring and
computer networking. Because of their small size and low power requirements, both modules are ideal for use
in portable, battery-powered applications such as hand-held terminals.
DS000022 Rev D July ‘99
©1999 REG No 277 4001, ENGLAND.
Page 1

1 Page





FM-TX2-XXX pdf, ピン配列
FM TRANSMITTER & RECEIVER
MODULES. (2ND GENERATION)
RX2 receiver:
FM-TX2-XXX
FM-RX2-XXX
www.DataSheet4U.com
fig. 3: RX2 block diagram
Pin description
RF in
(pin 1)
50RF input from the antenna,
it is DC isolate internally. (see
antenna section of RX2
applications note for suggested
antenna/feeds).
RF GND
(pin 2)
RF ground pin, internally
connected to the module screen
and pin 4 (0V). This pin should
be connected to the RF return
path (e.g. coax braid, main PCB
ground plane etc.)
fig. 4: physical dimensions
CD (pin 3)
The Carrier Detect may be used to drive an external PNP transistor to obtain a logic
level carrier detect signal, see test circuit / applications note. If not required it should
be connected to pin 5 (Vcc).
0volt
(pin 4)
Supply ground connection, connected to pin 1 and screen.
Vcc (pin 5)
+ve supply pin. +3.0V to +6.0V @ <17mA . The supply must be clean < 2mVP-P ripple. A
10µF de-coupling capacitor and 10series resistor is recommended if a clean supply is
not available.
AF (pin 6)
This is a buffered and filtered analogue output from the FM demodulator. It has a
standing DC bias of 1.2V and 400mV P-P base band signal. It is useful as a test point or
to drive linear decoders. Load impedance should be > 2kand < 100pF.
RXD
(pin 7)
This digital output from the internal data slicer is a squared version of the signal on
pin 6 (AF). It may be used to drive external decoders. The data is true data, i.e. as fed
to the transmitter. Load impedance should be > 1kand < 1nF
DS000022 Rev D July ‘99
©1999 REG No 277 4001, ENGLAND.
Page 3


3Pages


FM-TX2-XXX 電子部品, 半導体
FM TRANSMITTER & RECEIVER
MODULES. (2ND GENERATION)
Module test circuits
FM-TX2-XXX
FM-RX2-XXX
www.DataSheet4U.com
fig.5: TX2 test circuit
fig.6: RX2 test circuit
The PNP transistor enables a CMOS compatible Carrier Detect signal to be derived from pin 3. If no CD signal required
pin 3 should be connected directly to pin 5 (Vcc)
Module mounting considerations
The modules may be mounted horizontally or vertically on an area of ground plane preferably
close to the antenna to minimise feed length. The receiver and it’s antenna should be kept away
from sources of interference (micro’s, SMPS etc.). The modules may be potted if required in a
viscous compound which can not enter the screen can..
Warning: Do NOT wash the modules. They are not hermetically sealed.
DS000022 Rev D July ‘99
©1999 REG No 277 4001, ENGLAND.
Page 6

6 Page



ページ 合計 : 9 ページ
 
PDF
ダウンロード
[ FM-TX2-XXX データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
FM-TX2-XXX

FM TRANSMITTER & RECEIVER MODULES

rfsolutions
rfsolutions


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap