DataSheet.jp

HFDOM44P-xxxSx の電気的特性と機能

HFDOM44P-xxxSxのメーカーはHanbit Electronicsです、この部品の機能は「44Pin Flash Disk Module」です。


製品の詳細 ( Datasheet PDF )

部品番号 HFDOM44P-xxxSx
部品説明 44Pin Flash Disk Module
メーカ Hanbit Electronics
ロゴ Hanbit Electronics ロゴ 




このページの下部にプレビューとHFDOM44P-xxxSxダウンロード(pdfファイル)リンクがあります。
Total 11 pages

No Preview Available !

HFDOM44P-xxxSx Datasheet, HFDOM44P-xxxSx PDF,ピン配置, 機能
HANBit
HFDOM44P-xxxSx
44Pin Flash Disk Module Min.16MB~Max.512MB, True IDE Interface
Mode, 3.3V/5.0V Operating
Part No. HFDOM44P-xxxSx
1. PRODUCT OVERVIEW
GENERAL DESCRIPTION
The HFDOM44P-xxxSx series 44Pin Flash Disk Module is a flash technology based with True IDE interface flash
memory card. It is constructed with flash disk controller chip and NAND-type (Samsung) flash memory device. The
HFDOM44P-xxxSx series operates in both 3.3-Volt and 5.0-Volt power supplies. It comes in capacity of 16, 32, 64, 128,
www.DataSheet4U.co1m92, 256, 384 MB and up to 512 MB formatted 44Pin type .
By optimizing flash memory management, the life of this HFDOM44P-xxxSx series can be extended to its maximum
level. Because the ECC function is included, the correctness of data transfer between the HFDOM44P-xxxSx series and a
True IDE compatible interface device can be guaranteed.
The HFDOM44P-xxxSx series is fully compatible with applications such as CPU card / board, set top box, industry /
military PC / Notebook, security equipment, measuring instrument and embedded systems.
FEATURES
- True IDE compatible host interface
- Direct plug in for 2.5IDE Connectors
- 44 pin 2.0mm IDE Connector
- Very high performance, very low power consumption
- Automatic error correction
- Support 3 power save mode : stop/idle/active
- Support for CIS implemented with 256 bytes of attribute memory
- 3.3V/5.0V operation voltage
- Host data transfer rate : 20MB/s
- Flash data transfer rate : 10MB/s
- Host Interface bus width : 8/16 bit Access
- Flash Interface bus width : 8 bit Access
- Capacity : Min. 16MB ~ Max. 512MB
- MTBF : 1,000,000 hours, minimum 30,000 insertions
- Operating vibration : 15G peak to peak maximum
- Operating shock : 1,000G maximum
PRODUCT SPECIFICATIONS
Capacities :
16, 32, 64, 128, 192, 256, 384 and up to 512 MB (formatted)
Power consumptions :
Read mode
30 mA (typ), 40 Ma (Max)
Write mode
30 mA (typ), 40 Ma (Max)
Stop mode
30 uA (typ)
Environment conditions :
Operating temperature
Storage temperature
0° C to + 60° C
- 25° C to + 85° C
Relative humidity
Mechanical conditions :
95%(Max)
Weight : Maximum 12.0g
Operating Voltage : 3.3V / 5.0V ± 10%
URL : www.hbe.co.kr
REV 1.0 (August.2002)
1 / 11
HANBit Electronics Co., Ltd.

1 Page





HFDOM44P-xxxSx pdf, ピン配列
HANBit
PHYSYCAL SPECIFICATIONS
HFDOM44P-xxxSx
www.DataSheet4U.com
Jumper
Master Slave
1,2 2,3
Close Close
2.7± 0.1
42.9± 0.1mm
Jumper
3
2
1
2
1
31.0± 0.5mm
9.9± 0.08mm
1.7± 0.08mm
48.4± 0.1mm
52.3± 0.3mm
< View from connector side >
4.4± 0.2mm
< View from Right side >
6.3± 0.2mm
Figure 1.1 44 pin Type Flash Disk Module Dimensions
URL : www.hbe.co.kr
REV 1.0 (August.2002)
3 / 11
HANBit Electronics Co., Ltd.


3Pages


HFDOM44P-xxxSx 電子部品, 半導体
HANBit
HFDOM44P-xxxSx
Signal Descriptions
Table 2.2 Signal Descriptions
Signal Name Dir.
Pin
Description
A[2:0]
-PDIAG
-DASP(LED)
www.DataSheet4U.com
-CS0, -CS1
D[15:00]
GND
-IOR
-IOW
IRQ
-RESET
In True IDE Mode only A[2:0] are used to select the one of eight registers in
I 33,35,36 the Task File, the remaining address lines should be grounded by the host.
This input / output is the Pass Diagnostic signal in the Master / Slave
I/O 34 handshake protocol.
This signal used either to drive an LED whenever the Disk Module is being
I/O 39 accessed or as indication of a second drive present. This signal is active low
when the Disk Module is busy.
CS0 is the chip select for the task file registers while CS2 is used to select
I 37,38 the Alternate Status Register and the Device Control Register.
3,4,5,6,
All Task File operations occur in byte mode on the low order bus D00-D07
while all data transfers are 16 bit using D00-D15.
7,8,9,10,
I/O 11,12,13,
14,15,16,
17,18
2,19,22, Ground.
24,26,
--
30,40,
43
I 25 This is an I/O Read strobe generated by the host.
The I/O Write strobe pulse is used to clock I/O data on the Card Data bus
into the Storage Card controller registers when the Storage Card is
I 23 configured to use the I/O interface. The clocking will occur on the negative to
positive edge of the signal (trailing edge).
O 31 In True IDE Mode signal is the active high Interrupt Request to the host.
I 1 This input pin is the active low hardware reset from the host.
VCC
-- 41,42 +5 V, +3.3 V power.
IORDY
-IOIS16
O 27 This output signal may be used as IORDY.
This output signal is asserted low when this device is expecting a word data
O 32 transfer cycle.
URL : www.hbe.co.kr
REV 1.0 (August.2002)
6 / 11
HANBit Electronics Co., Ltd.

6 Page



ページ 合計 : 11 ページ
 
PDF
ダウンロード
[ HFDOM44P-xxxSx データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
HFDOM44P-xxxSx

44Pin Flash Disk Module

Hanbit Electronics
Hanbit Electronics


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap