|
|
D356AのメーカーはDurelです、この部品の機能は「Electroluminescent Lamp Driver IC」です。 |
部品番号 | D356A |
| |
部品説明 | Electroluminescent Lamp Driver IC | ||
メーカ | Durel | ||
ロゴ | |||
このページの下部にプレビューとD356Aダウンロード(pdfファイル)リンクがあります。 Total 12 pages
General Description:
The DurelÒ D356A is part of a family of highly integrated EL
drivers based on Durel’s patented three-port (3P) topology, which
offers built-in EMI shielding. This high efficiency device is well
suited for backlighting most timepieces and liquid crystal displays
for portable electronic applications.
www.DataSheet4U.com
Data Sheet
D356A
Electroluminescent
Lamp Driver IC
D356A
MSOP-8
Features
• High Efficiency
• Low Voltage Operation
• Small System Footprint
• Capacitor or External Clock LF Control
Applications
• Watches
• Data Organizers/PDAs
• Pagers
• LCD and Keypad Backlighting
Lamp Driver Specifications:
(Using Standard Test Circuit at Ta=25 °C unless otherwise specified.)
Parameter
Symbol Minimum Typical Maximum
Standby Current
10
Supply Current
I
23
Enable Current
50
Output Voltage
Vout
110
135
Lamp Frequency
LF
230 310
Inductor Frequency HF
23
100
30
75
220
390
Unit
nA
mA
uA
Vpp
Hz
kHz
Conditions
E = GND
E = 3.0V
E = 3.0V
CLF=5.0 nF
Standard Test Circuit
1.8mH
(3 Ohms)
1 GND
2 L-
3 VOUT
E8
CLF2 7
CLF1 6
3.0V
GND ON
OFF
5.0nF
4 L+
D356A
V+ 5
0.1µF
Load B
3.0 Vdc
1
1 Page Typical Performance Characteristics Using Standard Test Circuit
www.DataSheet4U.com
450
400
350
300
250
200
150
100
50
0
12 3456
DC Input Voltage
Output Frequency vs. DC Supply
Voltage
7
450
400
350
300
250
200
150
100
50
0
-40
-20
0
20 40 60
Tem perature ( °C)
Output Frequency vs. Ambient
T emp erat ure
80
240
200
160
120
80
40
0
12 345 6
DC Input Voltage
Output Voltage vs. DC Supply Voltage
7
240
200
160
120
80
40
0
-40 -20 0 20 40 60
Tem perature (°C)
Output Voltage vs. Ambient
T emp erat ure
80
50
40
30
20
10
0
1234567
DC Input Voltage
Supply Current vs. DC Supply Voltage
3
50
40
30
20
10
0
-40 -20
0
20 40 60
Tem perature (°C)
Supply Current vs. Ambient
T emp erat ure
80
3Pages Designing With D356A
I. Lamp Frequency Capacitor (CLF) Selection
Selecting the appropriate value of capacitor for the low frequency oscillator (CLF) will set the output frequency of the
D356A inverter. Figure 1 graphically represents the inversely proportional relationship between the CLF capacitor
value and the oscillator frequency. In this example at V+ = 3.0V, LF=1600 nF-Hz/CLF.
www.DataSheet4U.com
900
800
700
600
500
400
300
200
100
0
01234 56789
CLF (nF)
Figure 1: Typical Lamp Frequency vs. CLF Capacitor
10
Alternatively, the lamp frequency may also be controlled with an external clock signal with a 50% duty cycle. The
output lamp frequency will be the same frequency as the input clock signal. For example, if a 250Hz input clock signal
is used, the resulting lamp frequency will be 250Hz. The clock signal input voltage should not exceed V+.
The selection of the CLF value can also affect the brightness of the EL lamp because of its control of the lamp
frequency (LF). Although input voltage and lamp size can change EL lamp frequency as well, LF mainly depends on
the CLF value selected or the frequency of the input clock signal to CLF. The luminance of various sizes of Durel 3
Blue-green EL lamp driven by a D356A at V+ = 3.0V using the same inductor value is shown in Figure 2 with respect
to lamp frequency.
8
7
6
5 2in2 EL Lamp
4 4in2 EL Lamp
3
2 6in2 EL Lamp
1
0
0 200 400 600 800 1000
Lamp Frequency (Hz)
Figure 2: Typical Lamp Luminance vs. Lamp Frequency
6
6 Page | |||
ページ | 合計 : 12 ページ | ||
|
PDF ダウンロード | [ D356A データシート.PDF ] |
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
部品番号 | 部品説明 | メーカ |
D356A | Electroluminescent Lamp Driver IC | Durel |