DataSheet.jp

ADAM-4510 の電気的特性と機能

ADAM-4510のメーカーはADAMです、この部品の機能は「(ADAM-4510 / ADAM-4520) Converter」です。


製品の詳細 ( Datasheet PDF )

部品番号 ADAM-4510
部品説明 (ADAM-4510 / ADAM-4520) Converter
メーカ ADAM
ロゴ ADAM ロゴ 




このページの下部にプレビューとADAM-4510ダウンロード(pdfファイル)リンクがあります。

Total 4 pages

No Preview Available !

ADAM-4510 Datasheet, ADAM-4510 PDF,ピン配置, 機能
SERIAL COMMUNICATION INTERFACE FOR INDUSTRIAL AUTOMATION
ADAM-4510/4510S
RS-422/485 Repeater
ADAM-4520
Isolated RS-232 to RS-422/485
Converter
Introduction
Most industrial computer systems come as standard
with RS-232 serial ports. Though widely accepted,
RS-232 has limited transmission speed, range and
networking capabilities. The RS-422 and RS-485
standards overcome these limitations by using
differential voltage lines for data and control signals.
The ADAM-4520 isolated converter lets you take
advantage of RS-422 and RS-485 on systems
originally equipped with RS-232. It transparently
converts RS-232 signals into isolated RS-422 or RS-
485 signals. You don't need to change your PC's
hardware or your software. The ADAM-4520 lets you
easily build an industrial grade, long distance
www.DcaomtamSuhneiceatti4oUn s.cyostmem with standard PC hardware.
The ADAM-4510/4510S repeater simply amplifies, or
boosts, existing RS-485 signals to enable them to
cover longer distances. It extends the communication
distance by 4000 ft (1200 m) or extends the number of
connected nodes by 32.
Intelligent RS-485 control
The RS-485 standard supports half-duplex
communication. This means that just two wires are
needed to both transmit and receive data. Handshak-
ing signals (such as RTS, Request To Send) are
normally used to control the direction of the data flow.
A special I/O circuit in the ADAM-4510/4510S and
ADAM-4520 automatically senses the direction of the
data flow and switches the transmission direction. No
handshaking signals are necessary—you can build an
RS-485 network with just two wires. This RS-485
control is completely transparent to the user. Software
written for half-duplex RS-232 works without
modification.
Isolation (ADAM-4510S/4520 only)
The ADAM-4510S/4520's Opto-isolators provide 3000
VDC of isolation to protect the host computer from
ground loops and destructive voltage spikes on the
RS-485 data lines.
Surge protection (RS-485 only)
ADAM-4510/4510S and ADAM-4520 offer internal
surge-protection on their data lines. Internal high
speed transient suppressors on each data line protect
the modules from dangerous voltages levels or spikes.
Tough industrial design
You can power the ADAM-4510/4510S and ADAM-
4520 with any unregulated power source between +10
and +30 VDC.
Their industrial-grade plastic shells can be mounted
on a DIN-rail, panel or in a piggybacked stack. You
make signal connections through plug-in screw
terminal blocks, guaranteeing easy installation,
maintenance and modification
Features
• Automatic internal RS-485 bus supervision
• No external flow control signals required for RS-
485
• Minimum 3000 VDC isolation protection
(ADAM-4510S/4520)
• Transient suppression on RS-485 data lines
• Baudrate up to 115.2 Kbps
• Networking up to 4000 feet
• Reserved space for termination resistors
• Power and data flow indicator for troubleshooting
• Power requirement: +10 to +30 VDC
• Mounts easily on DIN-rail or panel
Specifications
Common
Power requirement:
Unregulated +10 to +30 VDC with protection from
power reversals
Case: ABS with captive mounting hardware
Accessories (Supplied):
NYLON DIN-rail Mounting Adapter
SECC Panel Mounting Bracket
Plug-in screw terminal wiring:
Accepts AWG 1-#12 to #22 (0.5 to 2.5 mm) wires
ADAM-4510/4510S specifications
Baudrate (bps): 1200, 2400, 4800, 9600, 19.2 K, 38.4
K, 57.6 K, 115.2 K, RS-422 (switchable)
Isolation Voltage: 3000 VDC (4510S only)
ADAM and the ADAM logo are trademarks of Advantech.
Part no. 2000000191 3rd Edition Printed in Taiwan Mar 1998

1 Page





ADAM-4510 pdf, ピン配列
SW2
Switch 2 sets the baudrate. The options range from
1200 bps to 115.2 Kbps. The factory default is 9600
bps. Be aware that when you change the baudrate,
you have to change the baudrate for all the connected
modules accordingly. If the RS-422 mode is ON, the
baudrate doesn't need to be set.
Default settings
Both Modules are not addressable by the host
computer, the baud rate and data format must be set
using SW1 and SW2 located inside the module. The
default settings are:
* Default settings for both modules
Function
Baud rate
Setting
9600 bps
Data format
10bits
ADAM-4510/4510S RS-422/RS-485 Repeater
Module
The following tables illustrate the switch settings for
the Repeater Module.
www.DataSheet4U.com
ADAM-4510/4510S Data format settings (SW1)
Data Format
9bits
12
¡¡
* 10bits
11bits
¡l
12bits
ll
¡= Open l= Closed * = Default
ADAM-4510/4510S Baud rate settings (SW2)
Baud Rate 1 2 3 4 5 6 7 8 9
1200 bps
2400 bps
4800 bps
*9600 bps
19.2 Kbps
38.4 Kbps
57.6 Kbps
115.2 Kbps
RS-422
¡= Open
l ¡ ¡ ¡ ¡ ¡¡ ¡¡
¡ l ¡ ¡ ¡ ¡¡ ¡¡
¡ ¡ l ¡ ¡ ¡¡ ¡¡
¡ ¡ ¡ l ¡ ¡¡ ¡¡
¡ ¡ ¡ ¡ l ¡¡ ¡¡
¡ ¡ ¡ ¡ ¡ l¡ ¡¡
¡ ¡ ¡ ¡ ¡ ¡l ¡¡
¡ ¡ ¡ ¡ ¡ ¡¡ l¡
¡ ¡ ¡ ¡ ¡ ¡¡ ¡l
l= Closed * = Default
ADAM-4520 RS-232/RS-485 Converter
Module
The following tables illustrate the switch settings for
the Converter Module.
ADAM-4520 Data format settings (SW1)
Data Format
9bits
12
¡¡
*10bits
11bits
¡l
12bits
ll
¡= Open l= Closed * = Default
ADAM-4520 Baud rate settings (SW2)
Baud Rate 1 2 3 4 5 6 7 8 9 10
RTS control l ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡
1200 bps ¡ l ¡ ¡ ¡ ¡ ¡ ¡ ¡ ¡
2400 bps
4800 bps
*9600 bps
19.2 Kbps
¡¡l¡¡¡¡¡¡¡
¡¡¡l¡¡¡¡¡¡
¡¡¡¡l¡¡¡¡¡
¡¡¡¡¡l¡¡¡¡
38.4 Kbps ¡ ¡ ¡ ¡ ¡ ¡ l ¡ ¡ ¡
57.6 Kbps ¡ ¡ ¡ ¡ ¡ ¡ ¡ l ¡ ¡
115.2 Kbps
RS-422
¡= Open
¡¡¡¡¡¡¡¡l¡
¡¡¡¡¡¡¡¡¡l
l= Closed * = Default
Power supply
For the ease of use in industrial environments the
ADAM modules are designed to accept industry
standard +24 VDC unregulated power. Operation is
guaranteed when using any power supply between
+10 and +30 VDC. Power ripples must be limited to 5 V
peak to peak while the voltage in all cases must be
maintained between +10 and +30 VDC. All power
supply specifications are referenced at module
connector.
The power cables should be selected according to the
number of modules connected and the length of the
power lines. When using a network with long cables,
we advise the use of thicker wire to limit the line
voltage drop. In addition to serious voltage drops, long
voltage lines can also cause interference with
communication wires.
ADAM-4510/4510S/4520 User's Manual


3Pages





ページ 合計 : 4 ページ
 
PDF
ダウンロード
[ ADAM-4510 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
ADAM-4510

(ADAM-4510 / ADAM-4520) Converter

ADAM
ADAM
ADAM-4510S

(ADAM-4510 / ADAM-4520) Converter

ADAM
ADAM


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap