DataSheet.jp

EK62 PDF Datasheet ( 特性, スペック, ピン接続図 )

部品番号 EK62
部品説明 EVALUATION KIT
メーカ Apex Microtechnology
ロゴ Apex Microtechnology ロゴ 



Total 2 pages
		

No Preview Available !

EK62 Datasheet, EK62 PDF,ピン配置, 機能
www.DataSheet4U.com
MICROTECHNOLOGY
&7"-6"5*0/,*5'034"&91)"4&#-%$.0503%3*7&3
EK62
)551888"1&9.*$305&$)$0.  "1&9  
INTRODUCTION
ASSEMBLY
The EK62 evaluation kit is designed to provide a convenient
way to breadboard design ideas for the SA305EX three Ø BLDC
motor driver IC. The PB119 evaluation board is pre-wired for
all required and recommended external components including
the ones for power supply bypassing and current sensing. The
PB119 also includes a breadboard area for constructing your
application circuit.
1. Solder surface mount ceramic capacitors C1 and C4 on the
component side of the board.
2. Solder the SIP socket into the board. Insert the IC fully into
the socket, noting the pin 1 location on the IC and the circuit
board.
3. Add 3 resistors for current sense. Refer to SA305U data-
sheet for acceptable values and power dissipation ratings
of current sense resistors.
PARTS LIST
4. Install the banana jacks for signals and power. Please note
that the banana jacks need to be installed on both sides of
Ref Apex P/N
Description/Vendor Qty
the board as shown in figure (only for low voltage signals
N/A HS14
Heat Sink
1
029372326215 SIP Socket
Loranger
1
N/A PB119
PC board
1
Many 571-0100
Y
Banana Jack
Deltron
22
C1, C4 OX7R105KWN
1 µF cap
2
Novacap 1825B105K201N
RC2, C5 140-ESRL100V100 100µF cap,
Xicon
2
AN/A TW12
Thermal Washer, Apex 1 Box
N/A 91920A865
Standoffs
McMaster-Carr
4
INRecommended Components (included in EK kit)
D1-D6 SB5100-T
Diode, 100V, 5A
6
PRELIMSCHEMATIC
and Vdd on the bottom end of the board).
5. Mount the electrolytic capacitors C2 and C5 in the specified
location in the board.
6. Solder the diodes D1-D6 provided with the kit for high cur-
rent applications.
7. Mount the standoffs in the four holes provided in the
board.
8. If a heat sink is used, position the thermal washer behind
the package tab of the IC in such a way that the hole on
the washer coincides with the hole on the tab and the heat
sink. Attach the IC to the heat sink in such a way that the
pins hang out of the heat sink. In the PC board remove the
two standoffs on the top of the board. Carefully insert the
part with the heat sink into the socket.
APEX MICROTECHNOLOGY CORPORATION • TELEPHONE (520) 690-8600 • FAX (520) 888-3329 • ORDERS (520) 690-8601 • EMAIL prodlit@apexmicrotech.com


1 Page





ページ 合計 : 2 ページ
PDF
ダウンロード
[ EK62.PDF ]

共有リンク

Link :

おすすめデータシート

部品番号部品説明メーカ
EK60

EVALUATION KIT

Apex Microtechnology
Apex Microtechnology
EK62

EVALUATION KIT

Apex Microtechnology
Apex Microtechnology
EK6703

TFT LCD Timing Controller

Fiti
Fiti

www.DataSheet.jp    |   2019   |  メール    |   最新    |   Sitemap