|
|
PDF IRMCF343 Data sheet ( Hoja de datos )
| Número de pieza | IRMCF343 | |
| Descripción | Sensorless Motor Control IC | |
| Fabricantes | International Rectifier | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de IRMCF343 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
Data Sheet No. PD60313
IRMCF343
Sensorless Motor Control IC for Appliances
www.DataSheet4U.com
Features
MCETM (Motion Control Engine) - Hardware based
computation engine for high efficiency sinusoidal
sensorless control of permanent magnet AC motor
Integrated Power Factor Correction control
Supports both interior and surface permanent
magnet motors
Built-in hardware peripheral for single shunt
current feedback reconstruction
No external current or voltage sensing operational
amplifier required
Three/two-phase Space Vector PWM
Three-channel analog output (PWM)
Embedded 8-bit high speed microcontroller (8051)
for flexible I/O and man-machine control
JTAG programming port for emulation/debugger
Serial communication interface (UART)
I2C/SPI serial interface
Watchdog timer with independent analog clock
Three general purpose timers/counters
Two special timers: periodic timer, capture timer
External EEPROM and internal RAM facilitate
debugging and code development
Pin compatible with IRMCK343, OTP-ROM version
1.8V/3.3V CMOS
Product Summary
Maximum crystal frequency
60 MHz
Maximum internal clock (SYSCLK) frequency 128 MHz
Sensorless control computation time
MCETM computation data range
11 μsec typ
16 bit signed
Program RAM loaded from external EEPROM 48K bytes
Data RAM
8K bytes
GateKill latency (digital filtered)
2 μsec
PWM carrier frequency counter
16 bits/ SYSCLK
A/D input channels
5
A/D converter resolution
12 bits
A/D converter conversion speed
2 μsec
8051 instruction execution speed
2 SYSCLK
Analog output (PWM) resolution
8 bits
UART baud rate (typ)
57.6K bps
Number of I/O (max)
23
Package (lead-free)
QFP64
Description
IRMCF343 is a high performance RAM based motion control IC designed primarily for appliance applications. IRMCF343 is
designed to achieve low cost and high performance control solutions for advanced inverterized appliance motor control.
IRMCF343 contains two computation engines. One is Motion Control Engine (MCETM) for sensorless control of permanent
magnet motors; the other is an 8-bit high-speed microcontroller (8051). Both computation engines are integrated into one
monolithic chip. The MCETM contains a collection of control elements such as Proportional plus Integral, Vector rotator, Angle
estimator, Multiply/Divide, Low loss SVPWM, Single Shunt IFB. The user can program a motion control algorithm by
connecting these control elements using a graphic compiler. Key components of the sensorless control algorithms, such as the
Angle Estimator, are provided as complete pre-defined control blocks implemented in hardware. A unique analog/digital circuit
and algorithm to fully support single shunt current reconstruction is also provided. The 8051 microcontroller performs 2-cycle
instruction execution (60MIPS at 120MHz). The MCE and 8051 microcontroller are connected via dual port RAM to process
signal monitoring and command input. An advanced graphic compiler for the MCETM is seamlessly integrated into the
MATLAB/Simulink environment, while third party JTAG based emulator tools are supported for 8051 developments. IRMCF343
comes with a small QFP64 pin lead-free package.
This document is the property of International Rectifier and may not be copied or distributed without expressed consent.
1 page  
IRMCF343
2 IRMCF343 Block Diagram and Main Functions
IRMCF343 block diagram is shown in Figure 2.
Figure 2. IRMCF343 Internal Block Diagram
IRMCF343 contains the following functions for sensorless AC motor control applications:
• Motion Control Engine (MCETM)
o Proportional plus Integral block
o Low pass filter
o Differentiator and lag (high pass filter)
o Ramp
o Limit
o Angle estimate (sensorless control)
o Inverse Clark transformation
o Vector rotator
o Bit latch
This document is the property of International Rectifier and may not be copied or distributed without expressed consent.
5
5 Page 
4.5 Test Interface Group
TSTMOD
P5.3/TDI
P5.1/TMS
TCK
P5.2/TDO
Must be tied to VSS, used only for factory testing.
Input, JTAG test data input
Input, JTAG test mode select
Input, JTAG test clock
Output, JTAG test data output
IRMCF343
This document is the property of International Rectifier and may not be copied or distributed without expressed consent.
11
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet IRMCF343.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| IRMCF341 | High Performance Appliance Motor Control IC | International Rectifier |
| IRMCF343 | Sensorless Motor Control IC | International Rectifier |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |