DataSheet.jp


Datasheet HI-8591 PDF ( 特性, スペック, ピン接続図 )

部品番号 HI-8591
部品説明 ARINC 429 LINE RECEIVER
メーカ Holt Integrated Circuits
ロゴ Holt Integrated Circuits ロゴ 
プレビュー
Total 7 pages
		
11

No Preview Available !

HI-8591 Datasheet, HI-8591 PDF,ピン配置, 機能
August 2006
HI-8591
ARINC 429 LINE RECEIVER
DESCRIPTION
The HI-8591 is an ARINC 429 bus interface receiver
designed to operate from a single 3.3 V or 5 V supply. The
part is designed with high-impedance inputs to minimize
bus loading, and has an exceptional input common-mode
performance in excess of +/- 30V, making it immune to
ground offsets around the aircraft. The RINA and RINB
inputs of the standard HI-8591 may be connected directly
to the ARINC 429 bus. To enable external lightning protec-
tion circuitry to be added, the HI-8591-40 variant is avail-
able. The HI-8591-40 requires only the addition of external
40 KW, ¼ watt resistors in series with RINA and RINB to
allow the part to meet the lightning protection requirements
of DO-160D level 3.
The typical 10 volt differential ARINC 429 signal is trans-
lated and input to a window comparator and latch. The
comparator levels are set just below the standard 6.5 volt
minimum ARINC data threshold and just above the stan-
dard 2.5 volt maximum ARINC null threshold.
The TESTA and TESTB inputs bypass the analog inputs for
testingwww.DataSheet4U.com purposes. Also if TESTA and TESTB are both taken
high, the digital outputs are forced to zero.
See Holt Application Note AN-300 for more information on
lightning protection.
FEATURES
! ARINC 429 line receiver interface in a
small outline package
! 3.3V single rail supply voltage
! +/-30 V common-mode performance
! >140 KOhm input impedance
! Lightning protection simplified with the
ability to add 40 KOhm external series
resistors
! Receiver input hysteresis at least 2 volt
! Test inputs bypass analog inputs and
force digital outputs to a one, zero or
null state
PIN CONFIGURATIONS
VCC - 1
TESTA - 2
RINB - 3
RINA - 4
8 - TESTB
7 - ROUTB
6 - ROUTA
5 - GND
HI-8591PSI, HI-8591PST & HI-8591PSM
HI-8591PSI-40, HI-8591PST-40 & HI-8591PSM-40
8 - PIN PLASTIC NARROW BODY SOIC
TESTA 1
RINB 2
RINA 3
NC 4
12 ROUTB
11 NC
10 ROUTA
9 NC
HI-8591PCI, HI-8591PCT, HI-8591PCI-40 & HI-8591PCT-40
16- pin 4mm x 4mm Chip-scale package
SUPPLY VOLTAGES
vcc = 3.3V ± 10%, 5.0V ± 10%
FUNCTION TABLE
RINA
-1.25V to 1.25V
-3.25V to -6.5V
3.25V to 6.5V
X
X
X
RINB
-1.25V to 1.25V
3.25V to 6.5V
-3.25V to -6.5V
X
X
X
TESTA
0
0
0
0
1
1
TESTB ROUTA ROUTB
0 00
0 01
0 10
1 01
0 10
1 00
PIN DESCRIPTION TABLE
SYMBOL
VCC
TESTA
RINB
RINA
GND
ROUTA
ROUTB
TESTB
FUNCTION
SUPPLY
LOGIC INPUT
ARINC INPUT
ARINC INPUT
POWER
LOGIC OUTPUT
LOGIC OUTPUT
LOGIC INPUT
DESCRIPTION
3.3V or 5V SUPPLY
CMOS
RECEIVER B INPUT
RECEIVER A INPUT
GROUND
RECEIVER CMOS OUTPUT A
RECEIVER CMOS OUTPUT B
CMOS
(DS8591, Rev. D)
HOLT INTEGRATED CIRCUITS
www.holtic.com
08/06

1 Page



HI-8591 pdf, ピン配列
HI-8591
ABSOLUTE MAXIMUM RATINGS
RECOMMENDED OPERATING CONDITIONS
Voltages referenced to Ground
Supply voltages
VCC......................................-0.3V to +7V
ARINC input - pins 3 & 4
Voltage at either pin.........+120V to -120V
DC current per input pin.................... ±10mA
Supply Voltages
VCC..............................3.3V to 5V ± 10%
Temperature Range
Industrial Screening........-40°C to +85°C
Hi-Temp Screening.......-55°C to +125°C
Military Screening.........-55°C to +125°C
Power dissipation at 25°C
plastic DIP............0.7W
ceramic DIP..........0.5W
Solder Temperature .........275°C for 10 sec
Storage Temperature........-65°C to +150°C
DC ELECTRICAL CHARACTERISTICS
NOTE: Stresses above absolute maximum
ratings or outside recommended operating con-
ditions may cause permanent damage to the
device. These are stress ratings only. Opera-
tion at the limits is not recommended.
OPERATING TEMPERATURE RANGE, VCC = 3.3V ± 10% or 5.0V ± 10% UNLESS OTHERWISE STATED
PARAMETERS
SYMBOL
TEST CONDITIONS
MIN TYP MAX UNITS
ARINC input voltage
one or zero
null
common mode
logic input voltage
high
low
ARINC input resistance
RINA to RINB
RINA or RINB to GND
RINA or RINB to VCC
VDIN
VNIN
VCOM
Differential volt., pins 3 & 4
"""
with respect to ground
VIH
VIL
R DIFF
R GND
R VCC
Supplies floating
""
""
6.5
-
-30.0
10 13 volts
- 2.5 volts
- +30.0 volts
70% VCC
-
- - volts
- 30% VCC volts
- 140 - KW
- 140 - KW
- 100 - KW
logic input current
source
sink
logic output drive voltage
one
IIH VIN = 2.0V
IIL VIN = 0.8V
VOH1
VOH2
VCC = 5V ± 10% IOH = 5mA
VCC= 3.3V ± 10% IOH = 1.5mA
-
-
2.4
2.4
- 20.0 µA
- 20.0 µA
--V
--V
zero
VOL1 VCC = 5V ± 10% IOH = 5mA
- - 0.5 V
VOL2 VCC = 3.3V ± 10% IOH = 1.5mA
-
- 0.4 V
Current drain
operating
ICC1 pins 2, 8 = 0V; pins 3, 4 open
- 1.5 5.0 mA
HOLT INTEGRATED CIRCUITS
3


3Pages


HI-8591 電子部品, 半導体
HI-8591 PACKAGE DIMENSIONS
inches (millimeters)
8-PIN PLASTIC SMALL OUTLINE (SOIC) - NB
(Narrow Body)
.1935 ± .0035
(4.915 ± .085)
.236 ± .008
(5.994 ± .203)
PIN 1
.1535 ± .0035
(3.90 ± .09)
Package Type: 8HN
.0086 ± .0012
(.2184 ± .0305)
.0165 ± .0035
(.4191 ± .0889)
Detail A
.055 ± .005
(1.397 ± .127)
.050 ± .010
(1.27 ± .254)
0° to 8°
.033 ± .017
(.8382 ± .4318)
Detail A
.0069 ± .0029
(.1753 ± .0737)
8-PIN CERDIP
.380 ± .004
(9.652 ± .102)
.005 MIN.
(.127 MIN.)
.248 ± .003
(6.299 ± .076)
.039 ± .006
(.991 ± .154)
.200 MAX.
(5.080 MAX.)
.100 ± .008
(2.540 ± .203)
.015 MIN.
(.381 MIN.)
Base Plane
.163 ± .037
(4.140 ± .940)
.056 ± .006
(1.422 ± .152)
Seating Plane
.018 ± .006
(.457 ± .152)
Package Type: 8D
.314 ± .003
(7.976 ± .076)
.350 ± .030
(8.890 ± .762)
.010 ± .006
(.254 ± .152`)
HOLT INTEGRATED CIRCUITS
6

6 Page





ページ 合計 : 7 ページ
PDF
ダウンロード
[ HI-8591.PDF ]

共有リンク

Link :

おすすめデータシート

部品番号部品説明メーカ
HI-8590

There is a function of ARINC 429 LINE DRIVER AND DUAL RECEIVER.

Holt Integrated Circuits
Holt Integrated Circuits
HI-8591

There is a function of ARINC 429 LINE RECEIVER.

Holt Integrated Circuits
Holt Integrated Circuits
HI-8592

There is a function of (HI-8592 - HI-8594) Single-Rail ARINC 429 Differential Line Driver.

Holt Integrated Circuit
Holt Integrated Circuit
HI-8593

There is a function of (HI-8592 - HI-8594) Single-Rail ARINC 429 Differential Line Driver.

Holt Integrated Circuit
Holt Integrated Circuit

多くを見つけるデータシート

部品番号部品説明メーカ
82S129

The 82S126 and 82S129 are field programmable, which means that custom patterns are immediately available by following the Signetics Generic fusing procedure. 1K-bit TTL Bipolar PROM, Address access time : 50ns max.

NXP
NXP
D1695

This part is a darlington connection NPN silicon epitaxial transistor. The 2SD1695 is a Darlington connection transistor and incorporates a dumper diode between the collector and emitter and a constant voltage diode and protection elements between the collector and base. This transistor is ideal for drives in solenoid and actuators.

NEC
NEC
FDMS86368

N-Channel Power Trench, 80V, 80A, 4.5mΩ.

Fairchild
Fairchild
2SC2456

Here is a Color TV Horizontal Driver, Vceo=300V, TO-126 Package.

Toshiba
Toshiba

www.DataSheet.jp    |   2018   |  メール    |   最新    |   Sitemap