DataSheet.jp

ISL6269B の電気的特性と機能

ISL6269BのメーカーはIntersil Corporationです、この部品の機能は「High-Performance Notebook PWM Controller」です。


製品の詳細 ( Datasheet PDF )

部品番号 ISL6269B
部品説明 High-Performance Notebook PWM Controller
メーカ Intersil Corporation
ロゴ Intersil Corporation ロゴ 




このページの下部にプレビューとISL6269Bダウンロード(pdfファイル)リンクがあります。

Total 16 pages

No Preview Available !

ISL6269B Datasheet, ISL6269B PDF,ピン配置, 機能
DATASHEET
High-Performance Notebook PWM Controller With
Audio-Frequency Clamp
ISL6269B
The ISL6269B IC is a Single-phase Synchronous-Buck PWM
controller featuring Intersil's Robust Ripple Regulator R3™
Technology that delivers truly superior dynamic response to
input voltage and output load transients. Integrated MOSFET
drivers and bootstrap diode result in fewer components and
smaller implementation area.
Intersil’s R3™ Technology combines the best features of
fixed-frequency PWM and hysteretic PWM while eliminating
many of their shortcomings. R3™ Technology employs an
innovative modulator that synthesizes an AC ripple voltage
signal VR, analogous to the output inductor ripple current. The
AC signal VR enters a window comparator where the lower
threshold is the error amplifier output VCOMP and the upper
threshold is a programmable voltage reference VW, resulting in
generation of the PWM signal. The voltage reference VW sets
the steady-state PWM frequency. Both edges of the PWM can be
modulated in response to input voltage transients and output
load transients, much faster than conventional fixed-frequency
PWM controllers. Unlike a conventional hysteretic converter, the
ISL6269B has an error amplifier that provides ±1% voltage
regulation at the FB pin.
The ISL6269B has a 1.5ms digital soft-start and can be
started into a pre-biased output voltage. A resistor divider is
used to program the output voltage setpoint. The ISL6269B
can be configured to operate in Continuous Conduction Mode
(CCM) or Diode Emulation Mode (DEM), which improves
light-load efficiency. In CCM the controller always operates as a
synchronous rectifier, however when DEM is enabled, the
low-side MOSFET is permitted to stay off, blocking negative
current flow into the low-side MOSFET from the output
inductor.
Features
• High performance R3™ Technology
• Fast transient response
• ±1% regulation accuracy: -10°C to +100°C and
-40° to +100°C
• Wide input voltage range: +5V to +25V
• Output voltage range: +0.6V to +3.3V
• Wide output load range: 0A to 25A
• Selectable diode emulation mode for increased light load
efficiency
• Programmable PWM frequency: 200kHz to 600kHz
• Pre-biased output start-up capability
• Integrated MOSFET drivers and bootstrap diode
• Internal digital soft-start
• Power-good monitor
• PWM minimum frequency above audible spectrum
• Fault protection
- Undervoltage protection
- Soft crowbar overvoltage protection
- Low-side MOSFET rDS(ON) overcurrent protection
- Over-temperature protection
- Fault identification by PGOOD pull-down resistance
• Pb-free (RoHS compliant)
Applications
• PCI express graphical processing unit
• Auxiliary power rail
• VRM
• Network adapter
November 17, 2014
FN6280.3
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas LLC 2006-2007, 2014. All Rights Reserved
Intersil (and design) and R3 Technology are trademarks owned by Intersil Corporation or one of its subsidiaries.
All other trademarks mentioned are the property of their respective owners.

1 Page





ISL6269B pdf, ピン配列
ISL6269B
Functional Pin Descriptions
GND (Bottom Pad)
Signal common of the IC. Unless otherwise stated, signals are
referenced to the GND pin, not the PGND pin.
VIN (Pin 1)
The VIN pin measures the converter input voltage which is a
required input to the R3™ PWM modulator. Connect across the
drain of the high-side MOSFET to the GND pin.
VCC (Pin 2)
The VCC pin is the input bias voltage for the IC. Connect +5V from
the VCC pin to the GND pin. Decouple with at least 1µF of a MLCC
capacitor from the VCC pin to the GND pin.
FCCM (Pin 3)
The FCCM pin configures the controller to operate in Forced
Continuous Conduction Mode (FCCM) or Diode Emulation Mode
(DEM.) DEM is disabled when the FCCM pin is pulled above the
rising threshold voltage VFCCMTHR, conversely DEM is enabled
when the FCCM pin is pulled below the falling threshold voltage
VFCCMTHF.
EN (Pin 4)
The EN pin is the on/off switch of the IC. The soft-start sequence
begins when the EN pin is pulled above the rising threshold
voltage VENTHR and VVCC is above the power-on reset (POR) rising
threshold voltage VVCC_THR. When the EN pin is pulled below the
falling threshold voltage VENTHF PWM immediately stops.
COMP (Pin 5)
The COMP pin is the output of the control-loop error amplifier.
Compensation components for the control-loop connect across
the COMP and FB pins.
FB (Pin 6)
The FB pin is the inverting input of the control-loop error
amplifier. The converter output voltage regulates to 600mV from
the FB pin to the GND pin. Program the desired output voltage
with a resistor network connected across the VO, FB and GND
pins. Select the resistor values such that FB to GND is 600mV
when the converter output voltage is at the programmed
regulation value.
FSET (Pin 7)
The FSET pin programs the PWM switching frequency. Program
the desired PWM frequency with a resistor and a capacitor
connected across the FSET and GND pins.
VO (Pin 8)
The VO pin measures the converter output voltage and is used
exclusively as an input to the R3™ PWM modulator. Connect at
the physical location where the best output voltage regulation is
desired.
ISEN (Pin 9)
The ISEN pin programs the threshold of the OCP overcurrent fault
protection. Program the desired OCP threshold with a resistor
connected across the ISEN and PHASE pins. The OCP threshold is
programmed to detect the peak current of the output inductor.
The peak current is the sum of the DC and AC components of the
inductor current.
PGND (Pin 10)
The PGND pin conducts the turn-off transient current through the
LG gate driver. The PGND pin must be connected to complete the
pull-down circuit of the LG gate driver. The PGND pin should be
connected to the source of the low-side MOSFET through a low
impedance path, preferably in parallel with the trace connecting
the LG pin to the gate of the low-side MOSFET. The adaptive
shoot-through protection circuit, measures the low-side MOSFET
gate-source voltage from the LG pin to the PGND pin.
LG (Pin 11)
The LG pin is the output of the low-side MOSFET gate driver.
Connect to the gate of the low-side MOSFET.
PVCC (Pin 12)
The PVCC pin is the input voltage bias for the LG low-side
MOSFET gate driver. Connect +5V from the PVCC pin to the PGND
pin. Decouple with at least 1µF of an MLCC capacitor across the
PVCC and PGND pins.
BOOT (Pin 13)
The BOOT pin stores the input voltage for the UG high-side
MOSFET gate driver. Connect an MLCC capacitor across the BOOT
and PHASE pins. The boot capacitor is charged through an
internal boot diode connected from the PVCC pin to the BOOT pin,
each time the PHASE pin drops below PVCC minus the voltage
dropped across the internal boot diode.
UG (Pin 14)
The UG pin is the output of the high-side MOSFET gate driver.
Connect to the gate of the high-side MOSFET.
PHASE (Pin 15)
The PHASE pin detects the voltage polarity of the PHASE node
and is also the current return path for the UG high-side MOSFET
gate driver. Connect the PHASE pin to the node consisting of the
high-side MOSFET source, the low-side MOSFET drain and the
output inductor.
PGOOD (Pin 16)
The PGOOD pin is an open-drain output that indicates when the
converter is able to supply regulated voltage. Connect the PGOOD
pin to +5V through a pull-up resistor.
Submit Document Feedback
3
FN6280.3
November 17, 2014


3Pages


ISL6269B 電子部品, 半導体
ISL6269B
Absolute Maximum Ratings
SEN, VIN to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +28V
VCC, PGOOD to GND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3V to +7.0V
PVCC to PGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +7.0V
GND to PGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +0.3V
EN, FCCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to GND, VCC +3.3V
VO, FB, COMP, FSET . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to GND, VCC +0.3V
PHASE to GND (DC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +28V
(<100ns Pulse Width, 10µJ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -5.0V
BOOT to GND, or PGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +33V
BOOT to PHASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +7V
UG (DC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to PHASE, BOOT +0.3V
(<200ns Pulse Width, 20µJ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -4.0V
LG (DC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to PGND, PVCC +0.3V
(<100ns Pulse Width, 4µJ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -2.0V
Recommended Operating Conditions
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to +85°C
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7V to 5.5V
Thermal Information
Thermal Resistance (Typical, Notes 4, 5) JA (°C/W) JC (°C/W)
QFN Package . . . . . . . . . . . . . . . . . . . . . . . .
48
11.5
Junction Temperature Range . . . . . . . . . . . . . . . . . . . . . . . -55C to +150C
Operating Temperature Range
ISL6269BCRZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-10°C to +100°C
ISL6269BIRZ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +100°C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to +150C
Pb-Free Reflow Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see TB493
Recommended Operating Conditions
Ambient Temperature Range
ISL6269BCRZ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-10°C to +100°C
ISL6269BIRZ. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +100°C
Supply Voltage (VIN to GND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V to 25V
VCC to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V ±5%
PVCC to PGND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5V ±5%
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
4. JA is measured in free air with the component mounted on a high effective thermal conductivity test board with “direct attach” features. See Tech
Brief TB379.
5. For JC, the “case temp” location is the center of the exposed metal pad on the package underside.
Electrical Specifications These specifications apply for TA = -40°C to +100°C, unless otherwise stated. All typical specifications
TA = +25°C, VCC = 5V, PVCC = 5V, VIN = 15V
PARAMETER
SYMBOL
TEST CONDITIONS
MIN TYP MAX UNIT
VIN
VIN Input Bias Current
VIN Shutdown Current
VCC and PVCC
VCC Input Bias Current
VCC Shutdown Current
PVCC Shutdown Current
VCC POR THRESHOLD
Rising VCC POR Threshold Voltage
Falling VCC POR Threshold Voltage
IVIN
IVIN_SHDN
EN = 5V, VIN = 5V
EN = 5V, VIN = 25V
EN = GND, VIN = 25V
IVCC EN = 5V, FCCM = GND, FB = 0.65V
IVCC_SHDN EN = GND, VCC = 5V
IPVCC_SHDN EN = GND, PVCC = 5V
VVCC_THR TA = -10°C to +100°C
VVCC_THF TA = -10°C to +100°C
6.5 10 µA
26 35 µA
0.1 1.0 µA
1.7 2.5 mA
0.1 1.0 µA
0.1 1.0 µA
4.35
4.33
4.10
4.08
4.45
4.45
4.20
4.20
4.55
4.55
4.30
4.30
V
V
V
V
REGULATION
Reference Voltage
Regulation Accuracy
VREF
FB connected to COMP
0.6 V
-1 +1 %
PWM
Frequency Range
fSW
fAUDIO
FCCM = 5V
FCCM = GND, TA = -10°C to +100°C
FCCM = GND
200 600 kHz
19 28
kHz
18 28
kHz
Frequency-Set Accuracy
VO Range
fSW = 300kHz
VVO
-12
0.60
+12
3.30
%
V
Submit Document Feedback
6
FN6280.3
November 17, 2014

6 Page



ページ 合計 : 16 ページ
 
PDF
ダウンロード
[ ISL6269B データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
ISL6269

Single Phase PWM Controller

Intersil Corporation
Intersil Corporation
ISL6269A

High-Performance Notebook PWM Controller

Intersil Corporation
Intersil Corporation
ISL6269B

High-Performance Notebook PWM Controller

Intersil Corporation
Intersil Corporation


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap