|
|
PDF ISL90462 Data sheet ( Hoja de datos )
| Número de pieza | ISL90462 | |
| Descripción | Digitally Controlled Potentiometer | |
| Fabricantes | Intersil Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ISL90462 (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
|
No Preview Available !
®
www.DataSheet4U.com
Data Sheet
ISL90462
Single Volatile 32-tap XDCP
October 7, 2005
FN8230.3
Digitally Controlled Potentiometer
(XDCP™)
The Intersil ISL90462 is a digitally controlled potentiometer
(XDCP). Configured as a variable resistor, the device
consists of a resistor array, wiper switches, a control section,
and volatile memory. The wiper position is controlled by a 2-
pin Up /Down interface.
The potentiometer is implemented by a resistor array
composed of 31 resistive elements and a wiper switching
network. Between each element and at either end are tap
points accessible to the wiper terminal. The position of the
wiper element is controlled by the CS and U/D inputs.
The device can be used in a wide variety of applications
including:
• LCD contrast control
• Parameter and bias adjustments
• Industrial and Automotive Control
• Transducer adjustment of pressure, temperature, position,
chemical, and optical sensors
• Laser Diode driver biasing
• Gain control and offset adjustment
Features
• Volatile Solid-State Potentiometer
• 2-pin UP/DN Interface
• DCP Terminal Voltage, 2.7V to 5.5V
• Tempco 35ppm/°C Typical
• 32 Wiper Tap Points
• Low Power CMOS
- Active current, 25µA max.
- Supply current 0.3µA
• Available RTOTAL Values = 10kΩ, 50kΩ, 100kΩ
• Temperature Range -40°C to +85°C
• Packages
- 6 Ld SC-70, SOT-23
• Pb-Free Plus Anneal Available (RoHS Compliant)
Pinout
ISL90462
(SOT23, SC70)
TOP VIEW
VDD
RH
GND
U/D
RW
CS
Ordering Information
PART NUMBER
ISL90462WIE627-TK
PART MARKING
AJS
RTOTAL (K)
10
TEMP RANGE (°C) PACKAGE (Tape and Reel) PKG. DWG. #
-40 to +85
6 Ld SC-70
P6.049
ISL90462WIE627Z-TK (See Note) DEK
-40 to +85
6 Ld SC-70 (Pb-free)
P6.049
ISL90462WIH627-TK
AKB
-40 to +85
6 Ld SOT-23
P6.064
ISL90462WIH627Z-TK (See Note) DEL
-40 to +85
6 Ld SOT-23 (Pb-free)
P6.064
ISL90462UIE627-TK
AJU
50
-40 to +85
6 Ld SC-70
P6.049
ISL90462UIE627Z-TK (See Note) DEI
-40 to +85
6 Ld SC-70 (Pb-free)
P6.049
ISL90462UIH627-TK
AKD
-40 to +85
6 Ld SOT-23
P6.064
ISL90462UIH627Z-TK (See Note) DEJ
-40 to +85
6 Ld SOT-23 (Pb-free)
P6.064
ISL90462TIE627-TK
AJT
100
-40 to +85
6 Ld SC-70
P6.049
ISL90462TIE627Z-TK (See Note) DEG
-40 to +85
6 Ld SC-70 (Pb-free)
P6.049
ISL90462TIH627-TK
AKC
-40 to +85
6 Ld SOT-23
P6.064
ISL90462TIH627Z-TK See Note) DEH
-40 to +85
6 Ld SOT-23 (Pb-free)
P6.064
NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are
RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed
the Pb-free requirements of IPC/JEDEC J STD-020
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
XDCP is a trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2005. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
1 page  
ISL90462
CS
tCU
tIH
tIC
U/D
tCI tIL
tSETTLE
RW
FIGURE 2. SERIAL INTERFACE TIMING DIAGRAM DECREMENT
Pin Descriptions
RH and RW
The ISL90462 contains a digital potentiometer with one
terminal tied to the ground pin (GND) of the device. The RH
pin is the other potentiometer terminal, and the RW pin is the
wiper terminal. The position of the wiper is controlled by the
CS- and U/D- inputs, with a movement "up" connecting the
wiper closer to the RH pin, and movement "down"
connection the wiper closer to the GND pin.
Up/Down (U/D)
The U/D input controls the direction of the wiper movement
and whether the counter is incremented or decremented.
Chip Select (CS)
The device is selected when the CS input is LOW. The
current counter value is stored in volatile memory when CS
is returned HIGH. When CS is high, the device is placed in
low power standby mode.
Principles of Operation
There are two sections of the ISL90462: the input control,
counter and decode section; and the resistor array. The input
control section operates just like an up/down counter. The
output of this counter is decoded to turn on a single
electronic switch connecting a point on the resistor array to
the wiper output. The resistor array is comprised of 31
individual resistors connected in series. At either end of the
array and between each resistor is an electronic switch that
transfers the connection at that point to the wiper. The RH
and RW terminals are uncommitted, and can for a variable
voltage divider if RH is connected to a voltage source.
The direction of the wiper movement is defined when the
device is selected. If during CS transition from High to Low
the U/D input is LOW, the wiper will move down on each
rising edge of U/D toggling. Similarly, the wiper will move up
on each rising edge of U/D toggling if, during CS transition
from High to Low, the U/D input is High.
The wiper, when at either fixed terminal, acts like its
mechanical equivalent and does not move beyond the last
position. That is, the counter does not wrap around when
clocked to either extreme.
If the wiper is moved several positions, multiple taps are
connected to the wiper for tSETTLE (U/D to RW change).
The 2-terminal resistance value for the device can
temporarily change by a significant amount if the wiper is
moved several positions.
5 FN8230.3
October 7, 2005
5 Page | ||
| Páginas | Total 7 Páginas | |
| PDF Descargar | [ Datasheet ISL90462.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ISL90460 | Digitally Controlled Potentiometer | Intersil Corporation |
| ISL90461 | Single Volatile 32-Tap XDCP | Intersil Corporation |
| ISL90462 | Digitally Controlled Potentiometer | Intersil Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |