DataSheet.jp

715P の電気的特性と機能

715PのメーカーはVishay Siliconixです、この部品の機能は「Polypropylene Film Capacitors ORANGE DROP」です。


製品の詳細 ( Datasheet PDF )

部品番号 715P
部品説明 Polypropylene Film Capacitors ORANGE DROP
メーカ Vishay Siliconix
ロゴ Vishay Siliconix ロゴ 




このページの下部にプレビューと715Pダウンロード(pdfファイル)リンクがあります。

Total 7 pages

No Preview Available !

715P Datasheet, 715P PDF,ピン配置, 機能
www.DataSheet4U.com
Polypropylene Film Capacitors
ORANGE DROP®, Low Loss
Type 715P
Vishay Sprague
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55°C to + 85°C standard; up to
+ 105°C when working voltage is reduced to 50% of the
+ 85°C rating.
Insulation Resistance: After a 2 minute charge at rated
voltage or 500 V, whichever is less.
At + 25°C: 400,000 Megohm for C .5µF.
200,000 Megohm - Microfarads for C > .5 Microfarads.
At + 85°C: 20,000 Megohm for C .5 Microfarads.
10,000 Megohm - Microfarads for C > .5 Microfarads.
At + 105°C: 2000 Megohm for C .5µF.
1000 Megohm - Microfarads for C > .5 Microfarads.
Capacitance, Tolerance and Dissipation Factor:
Capacitors shall be measured at a frequency of 1000Hz
at + 25°C or else be referred to measurements made at
that frequency and temperature. The maximum dissipation
factor shall be 0.1%.
Dielectric Withstanding Voltage: Capacitors rated below
1000 volts shall withstand a DC potential of 250% of rated
voltage applied between terminals for not more than
5 seconds. Capacitors rated 1000 volts and above shall
withstand a DC potential of 200% of rated voltage applied
between the terminals for not more than 5 seconds. The
test voltage must be applied and discharged through a
resistor of one ohm per volt.
Polypropylene plastic film is employed as the dielectric in Type
715P ORANGE DROP® capacitors. Type 715P capacitors
are ideal for applications where high AC current flow is found,
as in certain solid-state TV vertical circuits,
r-f generators and pulse-forming networks where dielectric
heating is often a problem.
The polypropylene dielectric film is similar to polystyrene in
that it can handle high AC currents due to its low loss but with
the added advantage of an operating temperature to
+ 105°C.
Capacitance change with temperature is less than 3% over
the entire operating temperature range. The temperature
coefficient is negative and virtually linear at 180PPM/°C over
the temperature range of + 25°C to + 105°C. This characteristic
means the Type 715P is suitable for matching with positive TC
resistors and inductors to maintain circuit stability.
Type 715P ORANGE DROP® capacitors are conformally
coated with a flame retardant epoxy.
Performance characteristics, as well as curves showing typical
variation in electrical characteristics as a function of temperature
and frequency, are given.
Humidity Test: Condition capacitors with no voltage
applied for 72 hours at 95% relative humidity and + 75°C.
Remove capacitors from humidity chamber, wipe surface
dry of moisture and dry in circulating air for 4 hours.
Measure insulation resistance after a two minute charge at
+ 25°C and rated voltage or 500 VDC, whichever is less.
Minimum product of insulation resistance and capacitance
shall be 50,000 Megohm-microfarads after test but need
not exceed 100,000 Megohm. Not more than one failure
in 12 units tested shall be permitted.
DC Life Test: Capacitors are capable of withstanding a
500 hour life test at + 85°C at 150% of rated working
voltage. After test, capacitance shall not have changed by
more than 5% of initial value, insulation resistance shall
not have decreased by more than 50% of the initial limit
and dissipation factor shall not have increased to more
than 0.1%.
AC Life Test: Capacitors shall withstand the maximum
60Hz voltage for a period of 500 hours at + 85°C.
Rated DC Voltage
200
400, 600
800, 1200, 1600
Maximum 60Hz Voltage
155
200
500
Not more than one failure allowed in 12 units tested.
Document Number: 42018
Revision 13-Nov-03
For technical questions, contact [email protected]
www.vishay.com
47

1 Page





715P pdf, ピン配列
Type 715P
Vishay Sprague
PERFORMANCE CHARACTERISTICS
1000
5
200
100
5
2
10
1
1000
600 V
.22µF .027µF
.0082µF
.12µF
2 5 10 2
5 100 2 5 1000
FREQUENCY - kHz
475
2
100
5
.027µF
.047.0µ0F82µ.0F027µ.F0.01053µ9FµF
2
1200 V
10
1
2
5 10 2
5 100 2 5 1000
FREQUENCY - kHz
1000
450
200
100
.056µF
.018µF
.1µF
.0056µF
5
2 800 V
10
12
1000
5 10 2
5 100 2 5 1000
FREQUENCY - kHz
500
2
.033µF
.01µF .0018µF
100 .0056µF
5 .018µF
2
1600 V
10
1
2
5 10 2
5 100 2 5 1000
FREQUENCY - kHz
STANDARD RATINGS* in inches [millimeters]
µF
± 10% TOLERANCE
PART NUMBER
200 VDC/155 VAC**
L
SIZE
D
.012
715P12392J
0.75 [19.05]
0.37 [9.40]
.015
715P15392J
0.75 [19.05]
0.37 [9.40]
.018
715P18392J
0.75 [19.05]
0.37 [9.40]
.022
715P22392J
0.75 [19.05]
0.37 [9.40]
.027
715P27392J
0.75 [19.05]
0.42 [10.67]
.033
715P33392J
0.75 [19.05]
0.42 [10.67]
.039
715P39392K
0.95 [24.13]
0.40 [10.16]
.047
715P47392K
0.95 [24.13]
0.40 [10.16]
.056
715P56392K
0.95 [24.13]
0.45 [11.43]
.068
715P68392K
0.95 [24.13]
0.45 [11.43]
.082
715P82392L
1.30 [33.02]
0.45 [11.43]
.1
715P10492L
1.30 [33.02]
0.45 [11.43]
.12
715P12492L
1.30 [33.02]
0.55 [13.97]
.15
715P15492L
1.30 [33.02]
0.55 [13.97]
.18
715P18492L
1.30 [33.02]
0.62 [15.75]
.22
715P22492L
1.30 [33.02]
0.62 [15.75]
.27
715P27492M
1.70 [43.18]
0.65 [16.51]
.33
715P33492M
1.70 [43.18]
0.65 [16.51]
.39
715P39492M
1.70 [43.18]
0.75 [19.05]
.47
715P47492M
1.70 [43.18]
0.75 [19.05]
* Shaded items, when ordered as ± 5% tolerance with D3 leads, are standard capacitors in stock and available through the Sprague® Distribution
Network. To complete the Type 715P Part Number, add the "D3" suffix and change the capacitance tolerance code number from a "9" to a "5"
to indicate ± 5% (i.e., 715P10456LD3). Any other Part Number, value or type may easily be ordered as a Special.
** 60Hz rms.
Document Number: 42018
Revision 13-Nov-03
For technical questions, contact [email protected]
www.vishay.com
49


3Pages


715P 電子部品, 半導体
Type 715P
Vishay Sprague
STANDARD MARKING FORMAT
SAMPLE MARKING
715P200 V
1239 9340
DESCRIPTION
715P
200 V
1239
9940
Sprague® Identification
Type Number
DC Voltage Rating, Volts
Capacitance and Tolerance Code
Weekly Date Code
(i.e. 40th week for 1999)
ORDERING INFORMATION
TOLERANCE CODES
PER EIA STANDARDS
9 = ± 10%
5 = ± 5%
2 = ± 2%
715P
TYPE
123
CAPACITANCE
92
TOLERANCE DC VOLTAGE
RATING @ + 85°C
J
CASE
CODE
D
TERMINAL
3
LEAD LENGTH
This is expressed in
picofarads. The first
two digits are
significant. The
third is the number
of zeros to follow.
Values must
conform to decade
rating for the
tolerance specified.
9 = ± 10%
5 = ± 5%
2 = ± 2%
This is expressed
in hundreds of
volts.
Example: 715P
R5 = 50 volts.
See
Dimensional
Configurations.
A = Straight lead.
B = Hairpin crimped.
D = Hockey crimped.
1 = 0.187" ± 0.030"
[4.750 ± 0.762]
2 = 0.250" ± 0.030"
[6.350 ± 0.762]
3 = 1.250" [31.750]
Minimum
www.vishay.com
52
For technical questions, contact [email protected]
Document Number: 42018
Revision 13-Nov-03

6 Page



ページ 合計 : 7 ページ
 
PDF
ダウンロード
[ 715P データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
7150-1

30mA Low Power LDO

Holtek
Holtek
7151

Submicro Axial Lead Lamp/Micro Axial Lead Lamps/Axial Lead Lamps

Gilway Technical Lamp
Gilway Technical Lamp
7153

T- Subminiature Lamps

Gilway Technical Lamp
Gilway Technical Lamp
7154

Submicro Axial Lead Lamp/Micro Axial Lead Lamps/Axial Lead Lamps

Gilway Technical Lamp
Gilway Technical Lamp


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap