IRPLLNR1 Datasheet PDF - IXYS Corporation
| Part Number | IRPLLNR1 | |
| Description | POWIRLIGHT REFERENCE DESIGN : LINEAR BALLAST | |
| Manufacturers | IXYS Corporation | |
| Logo |  |
|
|
There is a preview and IRPLLNR1 download ( pdf file ) link at the bottom of this page. Total 15 Pages | ||
Preview 1 page No Preview Available !
www.DataSheet4U.com
Reference Design Data Sheet (August, 1997)
IRPLLNR1
POWIRLIGHTTM REFERENCE DESIGN : LINEAR BALLAST
Features
• Drive 2X40WT12
• Universal Input (90-255Vac)
• High Power Factor (0.99) & Low THD
• High-Frequency Operation (40kHz)
• Lamp Filament Preheating
• Lamp Fault Protection with Auto-Restart
• Over Temperature Protection
• IR2153 HVIC Ballast Controller
Description
The IRPLLNR1 is a high efficiency, high
power factor, non-dimmable electronic ballast
designed for linear fluorescent lamp types.
The design contains an active power factor
correction circuit for universal voltage input
and a ballast control circuit using the IR2153
for controlling the lamp. Other features
include EMI filtering, transient protection and
lamp fault protection. The IRPLLNR1 is
intended as a reference design to be used as
development tool to speed up customers’
time to market.
Block Diagram
EMI Filter
Rectifier
PFC
Half-Bridge Output Stage Lamps
Line
PFC Control
IR2153
Fault Logic
Reference Design Data Sheet intended for design information only.
Subjected to changes without prior notice.
1
|
| |
 
www.DataSheet4U.com
IRPLLNR1
Fault Protection
The shutdown circuitry consists of 2 quad comparator ICs (IC2 and IC4), a current detection
filter (R21, R22, C16 and D12), a pull-up lamp removal circuit (R23, R24, R25, R26, D16 and
C22), and over-current sensing resistors (R47, R48, R49, R43, R44, R46, D10 and D19). A
more detailed diagram of the logic circuitry is given in the Ballast Control Logic and Timing
sections of this paper. The current detection filter rectifies and integrates a measurement of
the lamp resonant current from the source of the lower MOSFET of the half-bridge and
compares it against a fixed threshold voltage. Should the current exceed the threshold in the
event of over-current due to a non-strike condition of the lamp or non-zero voltage switching of
the half-bridge due to an open circuit or broken lamp cathodes, the CT pin of the IR2153 is
latched below the internal shutdown threshold (1/6 Vcc) and the ballast is shutdown.
In the event of a lamp exchange, the latch is reset with the pull-up network at the lamp,
and the CT pin of the IR2153 is held below the internal shutdown threshold in an unlatched
state (see Timing Diagram). When a new lamp is re-inserted, the ballast performs an auto
restart without a recycling of the input line voltage. During a lamp removal, the frequency is
also reset to the preheat frequency to avoid damage to the half-bridge switches due to below-
resonance operation which can occur upon re-insertion of the lamp. For a dual lamp ballast, a
second pull-up network is added to the second lamp (R27, R28, R29, R30) and is ‘OR-ed’
together with the first lamp. If either lamp is removed during running, the ballast is shutdown.
In the event of a broken upper cathode by either lamp during normal operation, non zero-
voltage switching occurs at the half-bridge and will be detected by the current detection filter at
source of the lower MOSFET of the half-bridge. Both half-bridge MOSFETs are latched off.
Should the DC bus decrease below a fixed threshold voltage during an undervoltage
condition of the line voltage, the frequency is shifted back up to the preheat frequency to fulfill
zero-voltage switching of the half-bridge, and the latch is disabled. This prevents latch-up
during a fast cycling of the line voltage or a brown out.
IRPLLNR1
Reference Design Data Sheet intended for design information only.
Subjected to changes without prior notice.
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for IRPLLNR1 electronic component. |
| Information | Total 15 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ IRPLLNR1.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| IRPLLNR1 | The function is POWIRLIGHT REFERENCE DESIGN : LINEAR BALLAST. IXYS Corporation | |
| IRPLLNR3 | The function is Universal Input Linear Fluorescent Ballast using the IR2167. International Rectifier |  |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
IRPL
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||