|
|
Número de pieza | UAF42 | |
Descripción | UNIVERSAL ACTIVE FILTER | |
Fabricantes | Burr-Brown Corporation | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de UAF42 (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
No Preview Available ! ®APPLICATION BULLETIN
Mailing Address: PO Box 11400 • Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd. • Tucson, AZ 85706
Tel: (602) 746-1111 • Twx: 910-952-111 • Telex: 066-6491 • FAX (602) 889-1510 • Immediate Product Info: (800) 548-6132
FILTER DESIGN PROGRAM FOR
THE UAF42 UNIVERSAL ACTIVE FILTER
By Johnnie Molina and R. Mark Stitt (602) 746-7592
Although active filters are vital in modern electronics, their
design and verification can be tedious and time consuming.
To aid in the design of active filters, Burr-Brown provides a
series of FilterPro™ computer-aided design programs. Us-
ing the FILTER42 program and the UAF42 it is easy to
design and implement all kinds of active filters. The UAF42
is a monolithic IC which contains the op amps, matched
resistors, and precision capacitors needed for a state-variable
filter pole-pair. A fourth, uncommitted precision op amp is
also included on the die.
Filters implemented with the UAF42 are time-continuous,
free from the switching noise and aliasing problems of
switched-capacitor filters. Other advantages of the state-
variable topology include low sensitivity of filter parameters
to external component values and simultaneous low-pass,
high-pass, and band-pass outputs. Simple two-pole filters
can be made with a UAF42 and two external resistors—see
Figure 1.
The DOS-compatible program guides you through the de-
sign process and automatically calculates component values.
Low-pass, high-pass, band-pass, and band-reject (or notch)
filters can be designed.
Active filters are designed to approximate an ideal filter
response. For example, an ideal low-pass filter completely
eliminates signals above the cutoff frequency (in the stop-
band), and perfectly passes signals below it (in the pass-
band). In real filters, various trade-offs are made in an
attempt to approximate the ideal. Some filter types are
optimized for gain flatness in the pass-band, some trade-off
gain variation or ripple in the pass-band for a steeper rate of
attenuation between the pass-band and stop-band (in the
transition-band), still others trade-off both flatness and rate
of roll-off in favor of pulse-response fidelity. FILTER42
supports the three most commonly used all-pole filter types:
Butterworth, Chebyshev, and Bessel. The less familiar In-
verse Chebyshev is also supported. If a two-pole band-pass
or notch filter is selected, the program defaults to a resonant-
circuit response.
Butterworth (maximally flat magnitude). This filter has the
flattest possible pass-band magnitude response. Attenuation
is –3dB at the design cutoff frequency. Attenuation beyond
the cutoff frequency is a moderately steep –20dB/decade/
pole. The pulse response of the Butterworth filter has mod-
erate overshoot and ringing.
Chebyshev (equal ripple magnitude). (Other transliterations
of the Russian Heby]ov are Tschebychev, Tschebyscheff
or Tchevysheff). This filter response has steeper initial rate
of attenuation beyond the cutoff frequency than Butterworth.
RF1
15.8kΩ
RF2
15.8kΩ
13
R2
50kΩ
87
R1
50kΩ
C1
1000pF
14
C2
1000pF
R3
2 50kΩ
VIN
A1
R4
50kΩ
A2
NOTE: A UAF42 and two external resistors make a unity-gain, two-pole, 1.25dB ripple
Chebyshev low-pass filter. With the resistor values shown, cutoff frequency is 10kHz.
FIGURE 1. Two-Pole Low-Pass Filter Using UAF42.
©1991 Burr-Brown Corporation
AB-035C
1
A3 1 VO
UAF42
11
Printed in U.S.A. July, 1993
1 page PP1
12
R3
2 50kΩ
VIN
3
RQ
HP Out
R2A
RF1
13
R2
50kΩ
BP Out
C1A RF2
87
R1
50kΩ
C1
1000pF
C2A
14
C2
1000pF
LP Out
1
A1 A2 A3
R4
50kΩ
UAF42
11
FIGURE 7. PP1 Noninverting Pole-Pair Subcircuit Using Internal Gain-Set Resistor R3.
PP2
HP Out
R2A
RF1
BP Out
C1A
RF2
LP Out
C2A
12 13
R2
50kΩ
87
R1
50kΩ
C1
1000pF
14 1
C2
1000pF
RG
VIN
3
A1
R4
50kΩ
A2
A3
RQ UAF42
11
FIGURE 8. PP2 Noninverting Pole-Pair Subcircuit Using External Gain-Set Resistor RG.
5
5 Page 11
11 Page |
Páginas | Total 14 Páginas | |
PDF Descargar | [ Datasheet UAF42.PDF ] |
Número de pieza | Descripción | Fabricantes |
UAF41 | Diode-Pentode | ETC |
UAF42 | UNIVERSAL ACTIVE FILTER | Burr-Brown Corporation |
UAF42 | Diode-Pentode | ETC |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |