|
|
UGN3189のメーカーはAllegro MicroSystemsです、この部品の機能は「(UGN3185 - UGN3189) HALL-EFFECT LATCHES FOR HIGH-TEMPERATURE OPERATION」です。 |
部品番号 | UGN3189 |
| |
部品説明 | (UGN3185 - UGN3189) HALL-EFFECT LATCHES FOR HIGH-TEMPERATURE OPERATION | ||
メーカ | Allegro MicroSystems | ||
ロゴ | |||
このページの下部にプレビューとUGN3189ダウンロード(pdfファイル)リンクがあります。 Total 8 pages
3185 THRU
3189
HALL-EFFECT LATCHES
FOR HIGH-TEMPERATURE OPERATION
V
CC
12
3
Dwg. PH-003A
Pinning is shown viewed from branded side.
These Hall-effect latches are extremely temperature-stable and stress-
resistant sensors especially suited for operation over extended temperature
ranges to +150°C. Superior high-temperature performance is made possible
through a novel Schmitt trigger circuit that maintains operate and release
point symmetry by compensating for temperature changes in the Hall ele-
ment. Additionally, internal compensation provides magnetic switch points
that become more sensitive with temperature, hence offsetting the usual
degradation of the magnetic field with temperature. The symmetry capability
makes these devices ideal for use in pulse-counting applications where duty
cycle is an important parameter. The four basic devices (3185, 3187, 3188,
and 3189) are identical except for magnetic switch points.
Each device includes on a single silicon chip a voltage regulator, qua-
dratic Hall-voltage generator, temperature compensation circuit, signal
amplifier, Schmitt trigger, and a buffered open-collector output to sink up to
25 mA. The on-board regulator permits operation with supply voltages of 3.8
to 24 volts.
The first character of the part number suffix determines the device
operating temperature range. Suffix ‘E–’ is for -40°C to +85°C, and suffix
‘L–’ is for -40°C to +150°C. Three package styles provide a magnetically
optimized package for most applications. Suffix ‘–LT’ is a miniature SOT89/
TO-243AA transistor package for surface-mount applications; suffix ‘–UA’ is
a three-lead ultra-mini-SIP.
ABSOLUTE MAXIMUM RATINGS
at TA = +25°C
Supply Voltage, VCC ............................ 30 V
Reverse Battery Voltage, VRCC ........... -30 V
Magnetic Flux Density, B ........... Unlimited
Output OFF Voltage, VOUT .................. 30 V
Reverse Output Voltage, VOUT .......... -0.5 V
Continuous Output Current, IOUT ..... 25 mA
Operating Temperature Range, TA
Suffix ‘E–’ ................... -40°C to +85°C
Suffix ‘L–’ ................. -40°C to +150°C
Storage Temperature Range,
TS ............................... -65°C to +170°C
FEATURES
s Symmetrical Switch Points
s Superior Temperature Stability
s Operation From Unregulated Supply
s Open-Collector 25 mA Output
s Reverse Battery Protection
s Activate With Small, Commercially Available Permanent Magnets
s Solid-State Reliability
s Small Size
s Resistant to Physical Stress
Always order by complete part number: the prefix ‘A’ + the basic four-digit
part number + a suffix to indicate operating temperature range +
a suffix to indicate package style, e.g., A3185ELT .
1 Page 3185 THRU 3189
HALL-EFFECT LATCHES
FOR HIGH-TEMPERATURE
OPERATION
TYPICAL OPERATING CHARACTERISTICS
A3185* SWITCH POINTS
300
A3187* SWITCH POINTS
150
200 OPERATE POINT
100
0
VCC = 12 V
100
OPERATE POINT
50
0
VCC = 12 V
-100
-200
RELEASE POINT
-300
-50 -25 0 25 50 75 100 125 150
AMBIENT TEMPERATURE IN °C
Dwg. GH-026
OUTPUT SATURATION VOLTAGE
300
I OUT = 20 mA
VCC = 4.5–24 V
200
-50
-100
RELEASE POINT
-150
-50
-25
7.0
0 25 50 75 100
AMBIENT TEMPERATURE IN °C
SUPPLY CURRENT
125 150
Dwg. GH-027
VCC = 12 V
6.0
B ≥ B OP
100
0
-50 -25
10
0 25 50 75 100
AMBIENT TEMPERATURE IN °C
SUPPLY CURRENT
125 150
Dwg. GH-029
5.0
B ≤ BRP
4.0
-50
-25
20
0 25 50 75 100
AMBIENT TEMPERATURE IN °C
OPERATE POINT
125 150
Dwg. GH-028
8.0
6.0 B ≥ B OP
B ≤ BRP
4.0
15
10
5.0
TA = +25°C
2.0
TA = +25°C
0
0
0 5 10 15 20 25
-5.0
0
5 10 15 20 25
SUPPLY VOLTAGE IN VOLTS
Dwg. GH-030
SUPPLY VOLTAGE IN VOLTS
Dwg. GH-037
* Complete part number includes a suffix denoting operating temperature range (E or L) and package type (LT or UA).
www.allegromicro.com
3Pages 3185 THRU 3189
HALL-EFFECT LATCHES
FOR HIGH-TEMPERATURE
OPERATION
PACKAGE DESIGNATOR ‘UA’
Dimensions in Inches
(controlling dimensions)
Dimensions in Millimeters
(for reference only)
0.164
0.159
4.17
4.04
0.062
45° 0.058
1.57
45° 1.47
0.122
0.117
0.085 1 2 3 0.031
MAX
0.640
0.600
45°
0.0173
0.0138
SEE NOTE
0.0189
0.0142
0.050
BSC
Dwg. MH-014E in
NOTES: 1.
2.
3.
4.
5.
6.
Tolerances on package height and width represent
allowable mold offsets. Dimensions given are
measured at the widest point (parting line).
Exact body and lead configuration at vendor’s option
within limits shown.
Height does not include mold gate flash.
Recommended minimum PWB hole diameter to clear
transition area is 0.035" (0.89 mm).
Where no tolerance is specified, dimension is nominal.
Supplied in bulk pack (500 pieces per bag).
3.10
2.97
2.16 1 2 3 0.79
MAX
16.26
15.24
45°
0.44
0.35
SEE NOTE
0.48
0.36
1.27
BSC
Dwg. MH-014E mm
Radial Lead Form (order A318xxUA-LC)
0.620"
0.500"
(15.7 mm
12.7 mm)
123
0.108"
(2.74 mm)
0.100"
(2.5 mm)
Dwg. MH-026
NOTE: Lead-form dimensions are the nominals produced on the
forming equipment. No dimensional tolerance is implied or
guaranteed for bulk packaging (500 pieces per bag).
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
6 Page | |||
ページ | 合計 : 8 ページ | ||
|
PDF ダウンロード | [ UGN3189 データシート.PDF ] |
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
部品番号 | 部品説明 | メーカ |
UGN3185 | (UGN3185 - UGN3189) HALL-EFFECT LATCHES FOR HIGH-TEMPERATURE OPERATION | Allegro MicroSystems |
UGN3187 | (UGN3185 - UGN3189) HALL-EFFECT LATCHES FOR HIGH-TEMPERATURE OPERATION | Allegro MicroSystems |
UGN3188 | (UGN3185 - UGN3189) HALL-EFFECT LATCHES FOR HIGH-TEMPERATURE OPERATION | Allegro MicroSystems |
UGN3189 | (UGN3185 - UGN3189) HALL-EFFECT LATCHES FOR HIGH-TEMPERATURE OPERATION | Allegro MicroSystems |