|
|
PDF HLP190 Data sheet ( Hoja de datos )
| Número de pieza | HLP190 | |
| Descripción | Range of Hybrid Linear Potentiometers | |
| Fabricantes | ETC | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de HLP190 (archivo pdf) en la parte inferior de esta página. Total 2 Páginas | ||
|
No Preview Available !
HLP 190
PERFORMANCE
Electrical stroke E
mm
Resistance ±10%
kΩ
Independent linearity
±%
Power dissipation at 20˚C
W
Applied voltage maximum Vdc
Electrical output
Resolution
Phasing between elements
Operational temperature
°C
Output smoothness
Insulation resistance
Operating mode
Wiper circuit impedance
Operating force maximum
gf
Life at 250mm per second
Shaft velocity maximum mm/s
Shaft seal
OPTIONS
Electrical stroke length
Resistance
Independent linearity
Intermediate taps
Upper temperature limit
Radiation hard models
AVAILABILITY
Instruments normally available
from stock
ORDERING CODES
The HLP190 range of hybrid linear potentiometers provides the facility for single
or dual electrical output with a body diameter of only 19mm. Stroke lengths are
from 25mm to 150mm, with a choice of body clamp (BS) or flange (FS)
mounting. This model is supplied with a spring loaded shaft, biased to the fully
extended position. Suited to a wide range of industrial applications for medium
stroke length requirements.
25 50 75 100 125 150
1 23 456
0.25 0.25 0.15 0.15 0.15 0.15
0.5 1.0 1.5 2.0 2.5 3.0
22 44 67 74 74 74
Single or dual - minimum of 0.5% to 99.5% applied volts
Virtually infinite
0.5mm total in retracted position (multi output units)
–30 to +100
To MIL-R-39023 grade C 0.1%
Greater than 100MΩ at 500Vdc
Voltage divider only - see Circuit Recommendations on page 2
Minimum of 100MΩ x track resistance or 0.5MΩ (whichever is greater)
450 475 500 525 550 600
6
Typically greater than 50 x 10 cycles at 25mm stroke length
1000
None fitted
Non standard electrical stroke lengths can be specified
500Ω to 5kΩ per 25mm of stroke length
25mm and 50mm stroke to ±0.075%; 75mm stroke upwards to ±0.05%
Can be specified (limited by a maximum of 14 flying leads)
May be extended in certain applications; please discuss with our engineers.
Can be built to special order
HLP190/FS, single electrical output, 25 to 150mm stroke length, standard resistance
BS = Body clamp mounting
with spring shaft
FS = Flange mounting
with spring shaft
Electrical outputs 1 = Single
2 = Dual
Stroke length mm
Resistance
HLP190/..... /..... /..... /.....
HLP190/SA, /BC and /FL models have been superseded by the
new SLS190 range.
Please see separate brochure for details.
Tope Co., Ltd. Tel: (02) 8228-0658 Fax: (02) 8228-0659 e-mail: [email protected] http://www.sensor.com.tw
1 page | ||
| Páginas | Total 2 Páginas | |
| PDF Descargar | [ Datasheet HLP190.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| HLP190 | Range of Hybrid Linear Potentiometers | ETC |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |