DataSheet.jp

ISP1109 の電気的特性と機能

ISP1109のメーカーはNXP Semiconductorsです、この部品の機能は「Universal Serial Bus transceiver with carkit support」です。


製品の詳細 ( Datasheet PDF )

部品番号 ISP1109
部品説明 Universal Serial Bus transceiver with carkit support
メーカ NXP Semiconductors
ロゴ NXP Semiconductors ロゴ 




このページの下部にプレビューとISP1109ダウンロード(pdfファイル)リンクがあります。

Total 30 pages

No Preview Available !

ISP1109 Datasheet, ISP1109 PDF,ピン配置, 機能
ISP1109
Universal Serial Bus transceiver with carkit support
Rev. 01 — 14 July 2005
Product data sheet
1. General description
The ISP1109 is a Universal Serial Bus (USB) transceiver device that supports
CEA936A, Mini-USB Analog Carkit Interface. It is fully compliant with Universal Serial
Bus Specification Rev. 2.0. The ISP1109 can transmit and receive serial data at full-speed
(12 Mbit/s) and low-speed (1.5 Mbit/s) data rates.
The ISP1109 is available in HVQFN32 package.
2. Features
s Fully complies with Universal Serial Bus Specification Rev. 2.0
s Supports CEA936A, Mini-USB Analog Carkit Interface
s Can transmit and receive serial data at full-speed (12 Mbit/s) and low-speed
(1.5 Mbit/s) data rates
s Supports Serial Parallel Interface (SPI) (up to 26 MHz) and I2C-bus (up to 400 kHz)
serial interface to access control and status registers
s Supports Universal Asynchronous Receiver-Transmitter (UART) pass-through on the
DP and DM lines
s Built-in analog switches to support analog audio signals multiplexed on the DP and DM
lines
s Supports On-The-Go (OTG) Session Request Protocol (SRP)
s Supports Power-down mode, in which the whole chip consumes less than 20 µA
power current
s 3.0 V to 5.25 V power supply input range (VCC)
s Supports wide range digital interfacing I/O voltage (VCC(I/O)) of 1.65 V to 3.6 V
s ±12 kV ESD protection at pins DP, DM, ID, VBUS, VCC, GNDA and GNDD
s Supports charger current switching (ISET) detection
s Full industrial grade operation from 40 °C to +85 °C
s Available in a small HVQFN32 (5 x 5 mm2) halogen-free and lead-free package.
3. Applications
s Mobile phones.

1 Page





ISP1109 pdf, ピン配列
Philips Semiconductors
5. Block diagram
ISP1109
USB transceiver with carkit support
VCC(I/O)
RESET_N
SPI_I2C_SEL
SPI_MISO
SPI_MOSI/
I2C_SDA
SPI_CLK/
I2C_SCL
SPI_CS/
I2C_ADR
INT_N
UART_TXD
UART_RXD
DAT/VP
SE0/VM
OE_N
RCV
VP
VM
SPEED
SUSPEND
GNDD
Fig 1. Block diagram.
8, 19
5
9
10
11
12
13
4
LEVEL
SHIFTER
25
26
18
17
20
16
15
14
6
7
die pad
CLOCK AND
TIMER
SPI
INTERFACE
REGISTERS
ISP1109
POWER
BLOCK
ID DET
3
21
30
31
28
29
I2C-BUS
INTERFACE
SERIAL CONTROLLER
DP_PU/
DP_INT
DETECTOR
ISET
27
CONTROL
DIF TX
23
22
+
DIF RX
SE DETECTOR
SE
D+
SE
D
32
AUDIO
SWITCH
1
2
24
004aaa486
VCC
REG3V3
VBUS
VREF
ID_PU
ID
ISET
DP
DM
MIC
SPKR_R
SPKR_L
GNDA
9397 750 13355
Product data sheet
Rev. 01 — 14 July 2005
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
3 of 59


3Pages


ISP1109 電子部品, 半導体
Philips Semiconductors
ISP1109
USB transceiver with carkit support
Table 2: Pin description…continued
Symbol [1] [2] Pin
Type [3] Reset Description
state
SPI_CLK/
I2C_SCL
12
I/OD
high-Z
SPI_CLK input — SPI clock input
I2C_SCL input and output — serial I2C-bus clock;
when used as an I2C-bus clock, the pad is
open-drain; connect to VCC(I/O) through a 3.3 k
resistor.
SPI_CS/
I2C_ADR
13
I
- SPI_CS input — SPI chip select input
I2C_ADR input — LSB address offset of the
I2C-bus slave address.
input
VM
14 O
- single-ended DM receiver output; leave this pin
open when not in use
push-pull output
VP
15 O
- single-ended DP receiver output; leave this pin
open when not in use
push-pull output
RCV
16 O
0 differential receiver output; leave this pin open
when not in use
push-pull output
SE0/VM
17
I/O high-Z SE0 input and output — SE0 functions in
DAT_SE0 USB mode
VM input and output — VM functions in VP_VM
USB mode.
bidirectional pad
DAT/VP
18
I/O high-Z DAT input and output — DAT functions in
DAT_SE0 USB mode
VP input and output — VP functions in VP_VM
USB mode.
bidirectional pad
VCC(I/O)
19
P
- supply voltage for the I/O interface logic signals
(1.65 V to 3.6 V)
OE_N 20 I
- enable differential transmitter input
input
REG3V3
21
P
- regulated output voltage 3.3 V; a 0.1 µF external
capacitor is required
DM
22
AI/O
high-Z this pin can be programmed as:
USB D(data minus pin)
transparent UART RxD or
transparent audio SPKR_L.
DP
23
AI/O
high-Z this pin can be programmed as:
USB D+ (data plus pin)
transparent UART TxD or
transparent audio SPKR_R or MIC.
GNDA 24 P
- analog ground
9397 750 13355
Product data sheet
Rev. 01 — 14 July 2005
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
6 of 59

6 Page



ページ 合計 : 30 ページ
 
PDF
ダウンロード
[ ISP1109 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
ISP1102

Advanced Universal Serial Bus transceiver

NXP Semiconductors
NXP Semiconductors
ISP1102BS

Advanced Universal Serial Bus transceiver

NXP Semiconductors
NXP Semiconductors
ISP1102W

Advanced Universal Serial Bus transceiver

NXP Semiconductors
NXP Semiconductors
ISP1103

Universal Serial Bus transceiver

NXP Semiconductors
NXP Semiconductors


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap