DataSheet.jp

DF7-4S-3.96DSA の電気的特性と機能

DF7-4S-3.96DSAのメーカーはHiroseです、この部品の機能は「3.96 mm Pitch Miniature Connectors for Internal Power Supplies (UL /C-UL and TUV Listed)」です。


製品の詳細 ( Datasheet PDF )

部品番号 DF7-4S-3.96DSA
部品説明 3.96 mm Pitch Miniature Connectors for Internal Power Supplies (UL /C-UL and TUV Listed)
メーカ Hirose
ロゴ Hirose ロゴ 




このページの下部にプレビューとDF7-4S-3.96DSAダウンロード(pdfファイル)リンクがあります。
Total 16 pages

No Preview Available !

DF7-4S-3.96DSA Datasheet, DF7-4S-3.96DSA PDF,ピン配置, 機能
3.96 mm Pitch Miniature Connectors for Internal Power Supplies (UL,C-UL and TÜV Listed)
DF7 Series
Complete
Locking
Function
Prevention of
Incorrect Connections
Completely
enclosed
locking system
Full barrier
between adjacent
contacts.
sFeatures
1. Complete Locking Function
Reliable interior lock protects mated connectors from
accidental disconnection.
2. Increased Contact Retention of Crimped
Contacts and Prevention of Incomplete
Insertion
Separate contact retainer increases the contact
retention, assures and visually confirms the complete
contact insertion.
3. Molded-in Contact Retention Tabs
Handling of terminated contacts during the assembly and
termination is easier and avoids entangling of wires,
since there are no protruding metal tabs.
4. Incorrect Insertion Prevention
Connectors are polarized to assure correct mating with
corresponding parts.
5.Solder Crack Prevention
Glass reinforced resin is used in the pin header bodies to
prevent solder cracks caused by the heat shrinkage.
6. Prevention of Incorrect Board Placement
Built-in locating posts assure correct connector
placement and orientation on the board.(2-12 pos.)
7. Supports Sealing after Installation.
Sealing compound can be applied to the board installed
connector for distance of 6 mm max. from the mounting
surface (9 mm max. for single position).
8.Cost Effective Tooling
The same crimping tools are used to terminate socket
and pin contacts.
9. Prevention of Short Circuits between
Adjacent Contacts
Each contact is completely surrounded by the insulator
housing, electrically isolating it from adjacent contacts.
Guide post
Board Eyelet mounting
One pos. type can also be mounted
to boards that have eyelets.
Continued.
2004.7
1

1 Page





DF7-4S-3.96DSA pdf, ピン配列
sProduct Specifications
Ratings
Current
rating
Voltage
rating
Row
1
2
No. of contacts AWG16 AWG18 AWG20 AWG22 AWG24 AWG26
2~10 10A
7A
5A
4A
4A
3A Operating temperature range -35ç to 85ç (Note 1)
4 10A 9A 7A 6A 4A 3A Operating humidity range
20% to 80%
6 9A 8A 6A 5A 4A 3A
8 9A 8A 6A 5A 4A 3A
Storage temperature range -10çto 60ç (Note 2)
10 8A 7A 5A 4A 4A 3A
Storage humidity range 40% to 70% (Note 2)
12 8A 7A 5A 4A 4A 3A
Specificatoin
AC630V
UL/C-UL/TÜV File No.and Recognition No
UL/C-UL
AC/DC 600V
UL :E52653
TÜV
AC/DC 600V(7.92mm pitch)
AC/DC 300V (3.96mm pitch)
C-UL
TÜV
:E52653
:R9750437
Item Specification
11. Contact resistance Contact resistance(Initial value)
12. Insulator resistance 1000 M ohms min.
13. Withstanding voltage No flashover or Insulator breakdown
14. Insertion-Extraction force
0.3N min., 4.5N max.
(per contact)
15. Durability
30 cycles
(mating/unmating)
16. Vibration
No momentary disconnections of 1 µs min.
17. Shock
No electrical discontinuity of 1 µs. min.
18. Humidity
Contact resistance 20 m ohms max.
19. Temperature cycle Contact resistance of 20 m ohms max.
10. Resistance to
soldering heat
No deformation of the insulator parts affecting
performance
Condition
10 m ohms max. 20mV max., 1mA
500 V DC
1500 V AC for 1 minute
Measured with a steel pin of 0.64 x 1.2 ± 0.002 mm
Contact resistance of 20 m ohms max.
Frequency 10 to 55 Hz, single amplitude of 0.75 mm, 3 axis, 2
hours
Acceleration of 490 m/s2, 11 ms duration, sine half-wave
waveform, 3 cycles in each of the 3 axis.
Temperature 40ç ± 2ç, 90% to 95% RH, 96 hours
(-55ç: 30 minutes ¡ 5 to 35ç: 5 minutes ¡ 85ç: 30 minutes ¡ 5
to 35ç: 5 minutes) for 5 cycles
Flow solder temperature 250ç, 10 seconds
Manual soldering: Soldering iron temperature 300ç, 3 seconds
Note 1: Includes temperature rise caused by the current flow.
Note 2: The term “storage” refers to products stored for long period of time prior to mounting and use. Operating Temperature Range
and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation.
sMaterials
Product Part Material
Sockets
Headers
In-line plug
Retainer
Crimp contacts
Insulator
Insulator
Contact
Insulator
Insulator
Contacts
Polyamide
Polyamide
(Glass reinforced)
High conductivity copper alloy
Polyamide
Polyamide
High conductivity copper alloy
Note: Hirose Electric's plating incorporates anti-whisking compounds.
Finish
Color: White
Color: Beige (Single row)
Color: Grey (Double row)
Tin-lead plating (Note)
Color: White
Color: Black
Tin plating (Note)
Remarks
UL94V-0
UL94V-0
----------------
UL94V-0
UL94V-0
----------------
3


3Pages


DF7-4S-3.96DSA 電子部品, 半導体
s In-line plug (Panel lock type)
Shown with terminated
and installed contacts.
Shown with terminated
and installed contacts.
1 Pos.
1 Pos.
Part Number
DF7- 1EP-3.96C
DF7- 2EP-3.96C
DF7- 3EP-3.96C
DF7- 4EP-3.96C
DF7- 5EP-3.96C
DF7- 6EP-3.96C
DF7- 7EP-3.96C
DF7- 8EP-3.96C
DF7- 9EP-3.96C
DF7-10EP-3.96C
CL No.
CL680-0134-4
CL680-0018-3
CL680-0019-6
CL680-0020-5
CL680-0021-8
CL680-0022-0
CL680-0023-3
CL680-0024-6
CL680-0025-9
CL680-0026-1
Number of contacts
1
2
3
4
5
6
7
8
9
10
A
6.44
10.40
14.36
18.32
22.28
26.24
30.20
34.16
38.12
42.08
B
-------------
3.96
7.92
11.88
15.84
19.80
23.76
27.72
31.68
35.64
Note1: Bag packaging (100 pieces/bag). Order by number of bags.
Note2: Refer to page 10 for retainer.
2 to 10 Pos.
12.44
6.44
2 to 10 Pos.
3
P=3.96
A
B
3
C
13.96
17.40
21.36
25.32
29.28
33.24
37.20
41.16
45.12
49.08
A1
Cavity No.
No. of contacts indicator
A1
No. of contacts
indicator
10
9.5
Cavity No.
B
Contact No.1
indicator
13.96
B Panel Cutout
1 Pos.
(11.32+X)+00.1
6.84+00.1
2.0
1.6
1.2
0.8
6
X
1.44
0.96
0.48
0
Y
0.88
0.96
1.44
1.92
C
2 to 10 Pos.
(C-Y)+00.1
(A+0.4)+00.1
10±0.2

6 Page



ページ 合計 : 16 ページ
 
PDF
ダウンロード
[ DF7-4S-3.96DSA データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
DF7-4S-3.96DS

3.96 mm Pitch Miniature Connectors for Internal Power Supplies (UL /C-UL and TUV Listed)

Hirose
Hirose
DF7-4S-3.96DSA

3.96 mm Pitch Miniature Connectors for Internal Power Supplies (UL /C-UL and TUV Listed)

Hirose
Hirose


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap