|
|
PDF MJF15031 Data sheet ( Hoja de datos )
| Número de pieza | MJF15031 | |
| Descripción | COMPLEMENTARY SILICON POWER TRANSISTORS 8 AMPERES 150 VOLTS 36 WATTS | |
| Fabricantes | Motorola Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MJF15031 (archivo pdf) en la parte inferior de esta página. Total 6 Páginas | ||
|
No Preview Available !
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
Complementary Power
Transistors
For Isolated Package Applications
Designed for general–purpose amplifier and switching applications, where the
mounting surface of the device is required to be electrically isolated from the heatsink
or chassis.
• Electrically Similar to the Popular MJE15030 and MJE15031
• 150 VCEO(sus)
• 8 A Rated Collector Current
• No Isolating Washers Required
• Reduced System Cost
• High Current Gain–Bandwidth Product
fT = 30 MHz (Min) @ IC = 500 mAdc
• UL Recognized, File #E69369, to 3500 VRMS Isolation
Order this document
by MJF15030/D
MJFN1P5N030
MJFP1N5P031
COMPLEMENTARY
SILICON
POWER TRANSISTORS
8 AMPERES
150 VOLTS
36 WATTS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎMAXIMUM RATINGS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎRating
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎCollector–Emitter Voltage
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎCollector–Base Voltage
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎEmitter–Base Voltage
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎRMS Isolation Voltage (1)
(for 1 sec, R.H. < 30%,
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎTA = 25_C)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎCollector Current — Continuous
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎΗ Peak
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎBase Current
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎTotal Power Dissipation* @ TC = 25_C
Derate above 25_C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎTotal Power Dissipation @ TA = 25_C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎDerate above 25_C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎOperating and Storage Junction Temperature Range
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎTHERMAL CHARACTERISTICS
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎCharacteristic
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎThermal Resistance, Junction to Ambient
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎThermal Resistance, Junction to Case*
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎLead Temperature for Soldering Purpose
CASE 221D–02
TO–220 TYPE
Test No. 1 Per Fig. 11
Test No. 2 Per Fig. 12
Test No. 3 Per Fig. 13
Symbol
VCEO
VCB
VEB
VISOL
IC
IB
PD
PD
TJ, Tstg
Symbol
RθJA
RθJC
TL
Value
150
150
5
4500
3500
1500
8
16
2
36
0.29
2
0.016
– 65 to + 150
Unit
Vdc
Vdc
Vdc
VRMS
Adc
Adc
Watts
W/_C
Watts
W/_C
_C
Max Unit
62.5 _C/W
3.5 _C/W
260 _C
* Measurement made with thermocouple contacting the bottom insulated mounting surface (in a location beneath the die), the device mounted on
a heatsink with thermal grease and a mounting torque of ≥ 6 in. lbs.
(1) Proper strike and creepage distance must be provided.
©MMoototorroollaa, IBncip. 1o9la95r Power Transistor Device Data
1
1 page  
TEST CONDITIONS FOR ISOLATION TESTS*
MOUNTED
FULLY ISOLATED
CLIP PACKAGE
LEADS
MOUNTED
FULLY ISOLATED
CLIP
PACKAGE
0.107” MIN
LEADS
MJF15030 MJF15031
MOUNTED
FULLY ISOLATED
PACKAGE
0.107” MIN
LEADS
HEATSINK
0.110” MIN
HEATSINK
Figure 11. Clip Mounting Position
for Isolation Test Number 1
Figure 12. Clip Mounting Position
for Isolation Test Number 2
* Measurement made between leads and heatsink with all leads shorted together
HEATSINK
Figure 13. Screw Mounting Position
for Isolation Test Number 3
MOUNTING INFORMATION
4–40 SCREW
PLAIN WASHER
CLIP
HEATSINK
COMPRESSION WASHER
NUT
HEATSINK
Figure 14. Typical Mounting Techniques*
Laboratory tests on a limited number of samples indicate, when using the screw and compression washer mounting technique, a screw
torque of 6 to 8 in . lbs is sufficient to provide maximum power dissipation capability. The compression washer helps to maintain a con-
stant pressure on the package over time and during large temperature excursions.
Destructive laboratory tests show that using a hex head 4–40 screw, without washers, and applying a torque in excess of 20 in . lbs will
cause the plastic to crack around the mounting hole, resulting in a loss of isolation capability.
Additional tests on slotted 4–40 screws indicate that the screw slot fails between 15 to 20 in . lbs without adversely affecting the pack-
age. However, in order to positively ensure the package integrity of the fully isolated device, Motorola does not recommend exceeding 10
in . lbs of mounting torque under any mounting conditions.
** For more information about mounting power semiconductors see Application Note AN1040.
Motorola Bipolar Power Transistor Device Data
5
5 Page | ||
| Páginas | Total 6 Páginas | |
| PDF Descargar | [ Datasheet MJF15031.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MJF15030 | COMPLEMENTARY SILICON POWER TRANSISTORS 8 AMPERES 150 VOLTS 36 WATTS | Motorola Semiconductors |
| MJF15030 | COMPLEMENTARY SILICON POWER TRANSISTORS |  ON |
| MJF15030 | SILICON POWER TRANSISTOR |  SavantIC |
| MJF15031 | COMPLEMENTARY SILICON POWER TRANSISTORS 8 AMPERES 150 VOLTS 36 WATTS | Motorola Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |