DataSheet.jp

MC14006BCL の電気的特性と機能

MC14006BCLのメーカーはMotorola Semiconductorsです、この部品の機能は「18-Bit Static Shift Register」です。


製品の詳細 ( Datasheet PDF )

部品番号 MC14006BCL
部品説明 18-Bit Static Shift Register
メーカ Motorola Semiconductors
ロゴ Motorola Semiconductors ロゴ 




このページの下部にプレビューとMC14006BCLダウンロード(pdfファイル)リンクがあります。
Total 6 pages

No Preview Available !

MC14006BCL Datasheet, MC14006BCL PDF,ピン配置, 機能
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
MC14002B (see Page 6-5)
MC14002UB (see Page 6-14)
MC14006B
18-Bit Static Shift Register
The MC14006B shift register is comprised of four separate shift register
sections sharing a common clock: two sections have four stages, and two
sections have five stages with an output tap on both the fourth and fifth
stages. This makes it possible to obtain a shift register of 4, 5, 8, 9, 10, 12,
13, 14, 16, 17, or 18 bits by appropriate selection of inputs and outputs. This
part is particularly useful in serial shift registers and time delay circuits.
Output Transitions Occur on the Falling Edge of the Clock Pulse
Fully Static Operation
Can be Cascaded to Provide Longer Shift Register Lengths
Supply Voltage Range = 3.0 Vdc to 18 Vdc
Capable of Driving Two Low–power TTL Loads or One Low–power
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎSchottky TTL Load Over the Rated Temperature Range
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎPin–for–Pin Replacement for CD4006B
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎMAXIMUM RATINGS* (Voltages Referenced to VSS)
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎSymbol
Parameter
Value
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVDD DC Supply Voltage
– 0.5 to + 18.0
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVin, Vout Input or Output Voltage (DC or Transient) – 0.5 to VDD + 0.5
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎlin, lout Input or Output Current (DC or Transient),
per Pin
± 10
Unit
V
V
mA
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎPD Power Dissipation, per Package†
500 mW
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎTstg Storage Temperature
– 65 to + 150
_C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎTL Lead Temperature (8–Second Soldering)
260 _C
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ* Maximum Ratings are those values beyond which damage to the device may occur.
†Temperature Derating:
Plastic “P and D/DW” Packages: – 7.0 mW/_C From 65_C To 125_C
Ceramic “L” Packages: – 12 mW/_C From 100_C To 125_C
L SUFFIX
CERAMIC
CASE 632
P SUFFIX
PLASTIC
CASE 646
D SUFFIX
SOIC
CASE 751A
ORDERING INFORMATION
MC14XXXBCP
MC14XXXBCL
MC14XXXBD
Plastic
Ceramic
SOIC
TA = – 55° to 125°C for all packages.
TRUTH TABLE
(Single Stage)
X = Don’t Care
Dn C
0
1
x
Qn+1
0
1
Qn
1
DP1
13 4
Q4 DP5
BLOCK DIAGRAM
11
Q8
12 5
10 6
Q9 DP10 Q13 DP14
8
Q17
9
Q18
VDD = PIN 14
VSS = PIN 7
NC = PIN 2
D
4
STAGES
C
D
4
STAGES
C
D
1
STAGE
C
D
4
STAGES
C
D
4
STAGES
C
D
1
STAGE
C
CLOCK 3
* Transmission Gate
DATA
(C)
1
#
IN OUT
2
(C)
REV 3
1/94
©MMOotoTrOolaR, IOncL. A199C5MOS LOGIC DATA
LOGIC DIAGRAM
(ONE REGISTER STAGE)
CC
*
C
D+1
#Inverter used only on the first stage of
C each four–stage element.
Input to output is
(A) A bidirectional low impedance when control input 1 is “low” and control input 2 is “high”.
(B) An open circuit when control input 1 is “high” and control input 2 is “low”.
MC14006B
25

1 Page





MC14006BCL pdf, ピン配列
ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ*SÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎOPCCCSHTWrehlllouooooteltIttttttdcccuppÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎTPTPTTPkkkpfauToLLLLLLCgtPPPTirHHHHHHmamHRuuuiÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ,,,m,,,tellliiIutttsssstttoNTTTePPPleeeenaHHHGHHHsÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎWFRaDLLLLLLnrgiCesie===ddi===lveqaHtÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎeF(((hu(((ya010010Anaen...T...l557n576Raldi55mcÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ6TrnnnACeFyinsnemssnahCf/ss//soplppea//lÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ/TrpFpFFprTEFFat)F))ihmc))C)RCCetÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎCCeCLeLLIt*SLLyrL+*++ipTs+++i2ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ52tcIi915C752ac.270lS5nn.c5sÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎnsn*nhsssna(CsraÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎLct=er5ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎis0tipcFsÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ,oTnAlÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎy=at2ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ255__CCÎÎÎÎ)ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎS.tyttttttTPPTTTWtmftsLcHLHLHhuÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎHHlbHHLLLo, lÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎVÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ555555511111111111111D.......050505050505050000000DÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎM211897————————————000028i005n000ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎTÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎΖ––1311y58817225464——10008p..51025500000030000.050ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ# ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎM21621246——18———————5400026...a5052000000xÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎMUÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎεnnnnnnHssssssiztÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ
#Data labelled “Typ” is not to be used for design purposes but is intended as an indication of the IC’s potential performance.
** When shift register sections are cascaded, the maximum rise and fall times of the clock input should be equal to or less than the rise and fall times
** of the data outputs driving data inputs, plus the propagation delay of the output driving stage for the output capacitance load.
This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However,
precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance
circuit. For proper operation, Vin and Vout should be constrained to the range VSS (Vin or Vout) VDD.
Unused inputs must always be tied to an appropriate logic voltage level (e.g., either VSS or VDD). Unused outputs must
be left open.
VDD = – VGS
Vout
14
CLOCK Q4
DP1
DP5
DP10
Q8
Q9
Q13
Q17
DP14 Q18
7 VSS
IOH
EXTERNAL
POWER
SUPPLY
Figure 1. Typical Output Source Current
Characteristics Test Circuit
VDD = VGS
Vout
14
CLOCK Q4
DP1
Q8
Q9
DP5 Q13
DP10 Q17
DP14 Q18
VSS
IOL
EXTERNAL
POWER
SUPPLY
Figure 2. Typical Output Sink Current
Characteristics Test Circuit
MOTOROLA CMOS LOGIC DATA
MC14006B
27


3Pages


MC14006BCL 電子部品, 半導体
–A–
14
1
G
OUTLINE DIMENSIONS
D SUFFIX
PLASTIC SOIC PACKAGE
CASE 751A–03
ISSUE F
8
–B– P 7 PL
0.25 (0.010) M B M
7
C R X 45 _
F
–T–
SEATING
PLANE
D 14 PL
K
0.25 (0.010) M T B S A S
M
J
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION.
4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.127 (0.005) TOTAL
IN EXCESS OF THE D DIMENSION AT
MAXIMUM MATERIAL CONDITION.
MILLIMETERS
INCHES
DIM MIN MAX MIN MAX
A 8.55 8.75 0.337 0.344
B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
F 0.40 1.25 0.016 0.049
G 1.27 BSC
0.050 BSC
J 0.19 0.25 0.008 0.009
K 0.10 0.25 0.004 0.009
M 0_ 7_ 0_ 7_
P 5.80 6.20 0.228 0.244
R 0.25 0.50 0.010 0.019
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided
in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters,
including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent
rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant
into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a
situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application,
Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or
unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered
trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454
MFAX: [email protected] – TOUCHTONE 602–244–6609
INTERNET: http://Design–NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MC14006B
30
*MC14006B/D*MOTOROLA CMOS LMOCG14I0C06DBA/DTA

6 Page



ページ 合計 : 6 ページ
 
PDF
ダウンロード
[ MC14006BCL データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
MC14006BCL

18-Bit Static Shift Register

Motorola Semiconductors
Motorola Semiconductors
MC14006BCP

18-Bit Static Shift Register

Motorola Semiconductors
Motorola Semiconductors


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap