DataSheet.jp

IH5016MPD の電気的特性と機能

IH5016MPDのメーカーはIntersil Corporationです、この部品の機能は「Virtual Ground Analog Switch」です。


製品の詳細 ( Datasheet PDF )

部品番号 IH5016MPD
部品説明 Virtual Ground Analog Switch
メーカ Intersil Corporation
ロゴ Intersil Corporation ロゴ 




このページの下部にプレビューとIH5016MPDダウンロード(pdfファイル)リンクがあります。
Total 3 pages

No Preview Available !

IH5016MPD Datasheet, IH5016MPD PDF,ピン配置, 機能
IH5009-5012, 5014,
5016-5020, 5022, 5024
MaF••y 1eSEIn9awat9ecti9tuhgcrrhCaeethessadnALnnoealgloCicgoCmSNaipgOlllneCaRtoeleEsrn-OCUeItnrOBmpateSMtlaorOAiMfla2:pLEc0pEceNVlTseiDocnEwlaEttiasPtDtihpoRPpRneMO@asEoDkPs1hU-ttL-aoC8Ar-0rTPCi0seE-.a4cMk4o2Em-N7T7DTtipnh4rhdeie7meussnaIHtcerryie5rad0ildp0eaf9tsoniirdgsoVenanmrniioeirlbsiettjaeauorcsyfatyiav-altneopa,-Gpulpolisecgrearo,fstoiwoiurnmnitenscax.hnpdeAcesenltAhswaiovennuerdgeahsvdlweeoloirtsswcgiaghtncilSefiootdysrwtthboiasiovtfiteahcll h
• Switching Speeds Less Than 0.5µs
not been sacrificed.
• ID(OFF) Less Than 500pA Typical at 70oC
• Effective rDS(ON) - 5to 50
• Commercial and Military Temperature Range
Operation
Each package contains up to four channels of analog gating
and is designed to eliminate the need for an external driver.
The odd numbered devices are designed to be driven
directly from TTL open collector logic (15 volts) while the
even numbered devices are driven directly from low level
TTL logic (5 volts). Each channel simulates a SPDT switch.
SPST switch action is obtained by leaving the diode cathode
unconnected; for SPDT action, the cathode should be
grounded (0V). The parts are intended for high performance
multiplexing and commutating usage. A logic “0” turns the
channel ON and a logic “1” turns the channel OFF.
Part Number Information
PART
NUMBER
CHANNELS
LOGIC
LEVEL
PKG
PACKAGE NO.
IH5009
4 +15 DD, PD
IH5010
4 +5 DD, PD
IH5011
4 +15 DE, PE
IH5012
4 +5 DE, PE
IH5014
3 +5 DD, PD
IH5016
3 +5 DE, PE
IH5017
2 +15 PA
IH5018
2 +5 DD, PA
IH5019
2 +15 DE, PA
IH5020
2 +5 DE, PA
IH5022
1 +5 DD, PA
IH5024
1 +5 PA
NOTE: Mil-Temperature range (-55oC to 125oC) available in ceramic
packages only.
IH50XX
M DE
PACKAGE
PA - 8 LEAD PDIP
PD - 14 LEAD PDIP
PE - 16 LEAD PDIP
DD - 14 LEAD CERDIP
DE - 16 LEAD CERDIP
TEMPERATURE RANGE
M = MILITARY (-55oC to 125oC)
C = COMMERCIAL (0oC to 70oC)
BASIC PART NUMBER
CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures.
Copyright © Harris Corporation 1999
4-1
File Number 3129.1

1 Page





IH5016MPD pdf, ピン配列
IH5009 Series
Absolute Maximum Ratings
Positive Analog Signal Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 30V
Negative Analog Signal Voltage . . . . . . . . . . . . . . . . . . . . . . . . .-15V
Diode Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10mA
Power Dissipation (Note) . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mW
Thermal Information
Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC
Operating Conditions
Temperature Range
5009C Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0oC to 70oC
5009M Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation
of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE: Dissipation rating assumes device is mounted with all leads welded or soldered to printed circuit board in ambient temperature below
75oC. For higher temperature, derate at rate of 5m/WoC.
Electrical Specifications (Per Channel)
PARAMETER
(NOTE 1)
SYMBOL
(NOTE 4)
TEST
CONDITIONS
(NOTE 2)
TYPE
-55oC (M)
0oC (C)
MIN/MAX
25oC
TYP MIN/MAX
125oC (M)
70oC (C)
MIN/MAX
UNITS
Input Current-ON
Input Current-OFF
Input Current-OFF
Channel Control
Voltage-ON
IIN(ON)
IIN(OFF)
ALL
5V Logic Ckts
IIN(OFF) 15V Logic Ckts
VIN(ON) 5V Logic Ckts
VIN = 0V, ID = 2mA
VIN = +4.5V,
VA = ±10V
VIN = +11V,
VA = ±10V
Note 3
- 0.01 ±0.5
- 0.04 ±0.5
- 0.04 ±0.5
0.5 - 0.5
100 µA
20 nA
20 nA
0.5 V
Channel Control
Voltage-ON
VIN(ON) 15V Logic Ckts Note 3
1.5 - 1.5
1.5 V
Channel Control
Voltage-OFF
VIN(OFF) 5V Logic Ckts
Note 3
-
- 4.5
4.5 V
Channel Control
Voltage-OFF
VIN(OFF) 15V Logic Ckts Note 3
- - 11.0 11.0 V
Leakage Current-OFF ID(OFF)
Leakage Current-OFF ID(OFF)
Leakage Current-ON ID(ON)
5V Logic Ckts
15V Logic Ckts
5V Logic Ckts
VIN = +4.5V,
VA = ±10V
VIN = +11V,
VA = ±10V
VIN = 0V, IS = 1mA
- 0.02 ±0.5
20 nA
- 0.02 ±0.5
20 nA
- 0.30 ±1.0 1000 (M) nA
200 (C)
Leakage Current-ON ID(ON)
15V Logic Ckts VIN = 0V, IS = 1mA
- 0.10 ±0.5 500 (M) nA
100 (C)
Leakage Current-ON ID(ON)
5V Logic Ckts
VIN = 0V, IS = 2mA
-
- 1.0
10 µA
Leakage Current-ON ID(ON)
15V Logic Ckts VIN = 0V, IS = 2mA
-
- 2.0 100 µA
Drain-Source
ON-Resistance
rDS(ON) 5V Logic Ckts
ID = 2mA, VIN = 0.5V
150
90
150
385 (M)
240 (C)
Drain-Source
ON-Resistance
rDS(ON) 15V Logic Ckts ID = 2mA, VIN = 1.5V
100
80
100
250 (M)
160 (C)
Turn-ON Time
Turn-OFF Time
Cross Talk
t(ON)
t(OFF)
CT
All
All
All
f = 100Hz
- 150 500
- 300 500
- 120 -
- ns
- ns
- dB
NOTES:
1. (OFF) and (ON) subscript notation refers to the conduction state of the FET switch for the given test.
2. Refer to Figure 1 for definition of terms.
3. VIN(ON) and VIN(OFF) are test conditions guaranteed by the tests of rDS(ON) and ID(OFF) respectively.
4. “5V Logic CKTS” applies to even-numbered devices. “15V Logic CKTS” applies to odd-numbered devices.
4-3


3Pages





ページ 合計 : 3 ページ
 
PDF
ダウンロード
[ IH5016MPD データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
IH5016MPA

Virtual Ground Analog Switch

Intersil Corporation
Intersil Corporation
IH5016MPD

Virtual Ground Analog Switch

Intersil Corporation
Intersil Corporation
IH5016MPE

Virtual Ground Analog Switch

Intersil Corporation
Intersil Corporation


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap