|
|
PDF RPM7140-V4 Data sheet ( Hoja de datos )
| Número de pieza | RPM7140-V4 | |
| Descripción | IR Receiver Module | |
| Fabricantes | ROHM Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de RPM7140-V4 (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
Photo Link Module
IR Receiver Module
RPM7100 series
RPM7100 series
RPM7100 series are remote control receiver modules. Small-sized, light-weight, and low current consumption modules
have been achieved by using resin mold.
!Applications
All household electric appliances such as TV, DVD, air conditioner and audio equipment.
!Features
1) Low current consumption. (0.95mA Typ.)
2) High ripple rejection.
3) 5 types of holders available for each set.
!RPM7100 series
Sub carrier
frequency
Height to lens
36.0kHz
36.7kHz
37.9kHz
40.0kHz
Straight type L forming
RSIP-A3 RSIP-A3 V4
5.5mm
RPM7136
RPM7137
RPM7138
RPM7140
4.8mm
RPM7136-V4
RPM7137-V4
RPM7138-V4
RPM7140-V4
Horizontal board
RSIP-A3 (H13)
15.0mm
∗RPM7136-H13
∗RPM7137-H13
∗RPM7138-H13
∗RPM7140-H13
with holders
Horizontal board
RSIP-A3 (H5)
9.6mm
Vertical board
RSIP-A3 (H4)
15.9mm
RPM7136-H5
RPM7137-H5
RPM7138-H5
RPM7140-H5
RPM7136-H4
RPM7137-H4
RPM7138-H4
RPM7140-H4
Vertical board
RSIP-A3 (H8)
7.2mm
Vertical board
RSIP-A3 (H9)
12.0mm
RPM7136-H8 RPM7136-H9
RPM7137-H8 RPM7137-H9
RPM7138-H8 RPM7138-H9
RPM7140-H8 RPM7140-H9
∗Under development
!Absolute maximum ratings (Ta = 25°C)
Parameter
Symbol
Supply Voltage
VCC
Storage temperature
Tstg
Operating temperature
Output Current
Topr
Io
Limits
6.3
−30 to +100
−10 to +75
2.0
Unit
V
˚C
˚C
mA
!Recommended operating conditions (Ta = 25°C)
Parameter
Symbol Min. Typ.
Supply Voltage
VCC 4.5 5.0
Max.
5.5
Unit
V
1/7
1 page  
Photo Link Module
RPM7100 series
!Notes
(1) All characteristics of the receiver in this specification are specified by supplying burst wave form (Fig.1) with ROHM
standard transmitter (Fig.2 ).
If in case of other burst wave form will be used, please check these spec. Carefully under the evaluations.
(2) When the receiver will be used as the wire-less remote controller, please use the signal method the signal format
which refer to “Measures to prevent mulfunctioning of IR remote-controlled electric home appliances”. (Published July
1987 by Association of Electric Home Appliances)
If using other signal method, signal format, (ex: signal format which not including the leader signal) the receiver might
have chances to miss-function.
(3) Please set up transmitter’s carrier frequency as same as the receiver’s f0 frequency. Otherwise error might be
occurred.
(4) If transmission signal has non-continues carrier, error might be occurred. Continuous carrier is necessary.
T1 T1≠T2
T2
(5) The receiver was designed to use as in-door use only.
Therefore, please understand that the receiver cannot cover all characteristics, in case of using it out-door.
(6) Noise environment (Light noise from inverter Lamp, and other kind of Lamps, Power ripple, electromagnetic noise from
power circuit, and etc) may cause a reduced effective distance.
(7) The receiver may not work properly if receiving signal judgement is done by single pulse due to the
surrounding / environmental noises.
To prevent such misjudgement, please make sure that the receiver is set up to work only when receiving
series of coded signal.
(8) Emitting unit (remote control transmitter) has to be considered about its emitting device function, characteristics and
characteristics of the receiver.
(9) Please connect ‘Holder’ on to the ‘Ground (GND)’ of PCB. If the holder is not connected to the GND, there is a
possibility of worsening the characteristics of product.
(10) Do not supply unnecessary stress to lead.
(11) Please pay careful attention to the lens.
It might have a chance to miss-function when the lens get dust or dirty. And also please do not touch the lens.
(12) In order to prevent products from ESD, human body and solder iron, etc. are required to be grounded.
5/7
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet RPM7140-V4.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| RPM7140-V4 | IR Receiver Module | ROHM Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |