DataSheet.jp

TEA1103 の電気的特性と機能

TEA1103のメーカーはNXP Semiconductorsです、この部品の機能は「Fast charge ICs for NiCd and NiMH batteries」です。


製品の詳細 ( Datasheet PDF )

部品番号 TEA1103
部品説明 Fast charge ICs for NiCd and NiMH batteries
メーカ NXP Semiconductors
ロゴ NXP Semiconductors ロゴ 




このページの下部にプレビューとTEA1103ダウンロード(pdfファイル)リンクがあります。

Total 28 pages

No Preview Available !

TEA1103 Datasheet, TEA1103 PDF,ピン配置, 機能
INTEGRATED CIRCUITS
DATA SHEET
TEA1103; TEA1103T;
TEA1103TS
Fast charge ICs for NiCd and NiMH
batteries
Preliminary specification
Supersedes data of 1997 Oct 09
File under Integrated Circuits, IC03
1999 Jan 27

1 Page





TEA1103 pdf, ピン配列
Philips Semiconductors
Fast charge ICs for NiCd and NiMH
batteries
Preliminary specification
TEA1103; TEA1103T;
TEA1103TS
QUICK REFERENCE DATA
SYMBOL
VP
IP
VNTC/VNTC
Vbat/Vbat
IVbat
Vbat(l)
IIB
IIB(max)
IIB(Lmax)
fosc
Vreg
PARAMETER
CONDITIONS
MIN.
supply voltage
supply current
outputs off
temperature rate dependent
(T/t) detection level
voltage peak detection level with
respect to top value
input current battery monitor
VNTC = 2 V;
Tj = 0 to 50 °C
Vbat = 2 V;
Tj = 0 to 50 °C
Vbat = 0.3 to 1.9 V
voltage at pin 19 for detecting low
battery voltage
5.5
battery charge current
maximum battery charge current
fast charge
10
top-off mode
voltage regulation full
NiCd and NiMH battery
maximum load current
no battery
oscillator frequency
regulating voltage
NiCd and NiMH
(pin Vstb open-circuit)
open battery
10
TYP.
4
0.25
0.25
1
0.30
3
10
40
1.325 or
Vstb
1.9
MAX.
11.5
100
200
UNIT
V
mA
%
%
nA
V
µA
µA
µA
µA
kHz
V
V
1999 Jan 27
3


3Pages


TEA1103 電子部品, 半導体
Philips Semiconductors
Fast charge ICs for NiCd and NiMH
batteries
Preliminary specification
TEA1103; TEA1103T;
TEA1103TS
INTRODUCTION
All battery types are initially fast charged with an
adjustable high current. Fast charge termination depends
upon the battery type. With NiCd and NiMH batteries the
main fast charge termination will be the T/t (temperature
detection) and/or peak voltage detection.
The fast charge period is followed by a top-off period for
NiCd and NiMH batteries. During the top-off period the
NiCd and NiMH batteries are charged to maximum
capacity by reduced adjustable charge current.
The top-off period ends after time-out or one hour
respectively.
After the top-off period, the TEA1103x switches over to the
standby mode. For NiCd and NiMH batteries either the
voltage regulation or trickle charge mode can be selected.
The voltage regulation mode is selected when the battery
includes a fixed load. Trickle charge prevents a discharge
of the battery over a long period of time.
Charging principles
CHARGING NiCd/NiMH BATTERIES
Fast charging of the battery begins when the power supply
voltage is applied and at battery insertion.
During fast charge of NiCd and NiMH batteries, the battery
temperature and voltage are monitored. Outside the
initialized temperature and voltage window, the system
switches over to the top-off charge current.
The TEA1103x supports detection of fully charged NiCd
and NiMH batteries by either of the following criteria:
• ∆T/t
Voltage peak detection.
If the system is programmed with T/t and Vpeak or, T/t
or Vpeak as the main fast charge termination, it
automatically switches to voltage peak detection if the
battery pack is not provided with a temperature sensing
input (NTC). In this way both packages, with and without
temperature sensor, can be used randomly independent of
the applied full detection method. Besides T/t and/or
voltage peak detection, fast charging is also protected by
temperature cut-off and time-out.
To avoid false fast charge termination by peak voltage
detection or T/t, full detection is disabled during a short
hold-off period at the start of a fast charge session.
After fast charge termination, the battery is extra charged
by a top-off period. During this period of approximately one
hour, the charge current is lowered thus allowing the
battery to be charged to nearly 100% before the system
switches over to standby.
After the battery has been charged to nearly 100% by the
top-off period, discharge of the battery (caused by a load
or by the self-discharge) can be avoided by voltage
regulation or by trickle charge.
If batteries are charged in combination with a load, the
TEA1103x can be programmed to apply voltage regulation
during the standby mode. In this way, discharge of the
battery caused by self-discharge or by an eventual load is
avoided. The regulating voltage is adjustable to the
voltage characteristic of the battery. For battery safety the
charge current is limited and the temperature is monitored
during voltage regulation. If a trickle charge is applied, the
self-discharge of the battery will be compensated by a
pulsating charge current.
To avoid the so called ‘memory effect’ in NiCd batteries, a
refresh can be manually activated. The discharge current
is regulated by the IC in combination with an external
power transistor. After discharging the battery to 1 V per
cell, the system automatically switches over to fast charge.
FUNCTIONAL DESCRIPTION
Control logic
The main function of the control logic is to support the
communication between several blocks. It also controls
the charge method, initialization and battery full detection.
The block diagram of the TEA1103x is illustrated in Fig.1.
Conditioning charge method and initializations
At system switch-on, or at battery insertion, the control
logic sets the initialization mode in the timer block.
After the initialization time the timer program pins can be
used to indicate the charging state using several LEDs.
The charge method is defined at the same time by the
following methods:
If the FCT pin is floating, the system will charge the
battery according to the charge characteristic of NiCd
and NiMH batteries.
The standby charge method (NiCd and NiMH), trickle
charge or voltage regulation, is defined by the input pin
Vstb. By biasing this voltage with a set voltage, the output
voltage will be regulated to the Vstb set voltage. If this pin
is connected to VS, or no NTC is connected the system
applies trickle charge.
1999 Jan 27
6

6 Page



ページ 合計 : 28 ページ
 
PDF
ダウンロード
[ TEA1103 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
TEA1100

Battery monitor for Nicd and NiMH chargers

NXP Semiconductors
NXP Semiconductors
TEA1100T

Battery monitor for Nicd and NiMH chargers

NXP Semiconductors
NXP Semiconductors
TEA1101

Battery monitor for Nicd and NiMH chargers

NXP Semiconductors
NXP Semiconductors
TEA1101T

Battery monitor for Nicd and NiMH chargers

NXP Semiconductors
NXP Semiconductors


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap