|
|
TEA0677TのメーカーはNXP Semiconductorsです、この部品の機能は「Dual pre-amplifier and equalizer for reverse tape decks」です。 |
部品番号 | TEA0677T |
| |
部品説明 | Dual pre-amplifier and equalizer for reverse tape decks | ||
メーカ | NXP Semiconductors | ||
ロゴ | |||
このページの下部にプレビューとTEA0677Tダウンロード(pdfファイル)リンクがあります。 Total 13 pages
INTEGRATED CIRCUITS
DATA SHEET
TEA0677T
Dual pre-amplifier and equalizer for
reverse tape decks
Product specification
File under Integrated Circuits, IC01
August 1993
1 Page This text is here in white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here in
_white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader.This text is here inThis text is here in
white to force landscape pages to be rotated correctly when browsing through the pdf in the Acrobat reader. white to force landscape pages to be ...
Instead of potentiometers at EQ AMP
fixed resistors may be used. The value
depends on applied heads.
Fig.1 Block and application diagram.
3Pages Philips Semiconductors
Dual pre-amplifier and equalizer for
reverse tape decks
Product specification
TEA0677T
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX. UNIT
AV open-loop gain
pins INA1/INA2 to pin OUTA
pins INB1/INB2 to pin OUTB
N equivalent noise voltage input
(RMS value)
(S+N)/N signal-plus-noise to noise ratio
f = 10 kHz
80 86
f = 400 Hz
104 110
unweighted;
− 0.7
20 Hz to 20 kHz;
Rsource = 0 Ω
internal gain 40 dB
linear;
68
74
− dB
− dB
1.4 µV
− dB
CCIR/ARM weighted;
DC output voltage; pins 1 (OUTA)
and 16 (OUTB)
see Fig.4
reference to VREF;
tape head DC coupled
−
−
±0.15 V
IOGND
IOVCC
ZO
DC output current capability
DC output current capability
output impedance
to ground
to VCC
−2 −
300 −
− 80
− mA
− µA
100 Ω
Switching thresholds
Equalization (pin 19)
VEQS
voltage at pin EQS
IEQ70
70 µs input current
IEQ120
120 µs input current
Head switch (pin 14)
−
−
−250
−
−
−
5
−150
−1000
V
µA
µA
VIN1 inputs INA1 and INB1 active
IIN1 maximum input current
VIN2 inputs INA2 and INB2 active
IIN2 maximum input current
note 1
0.65VCC 0.775VCC 1.0VCC V
−150 90
150 µA
0.1VCC 0.225VCC 0.35VCC V
−50 −90
−150 µA
Note to the characteristics
1. For an application with a fixed EQ time constant of 120 µs the equalizing network may be applied completely
external. In this application the 8.2 kΩ resistor has to be changed to 14 kΩ and the internal resistor REQ = 5.8 kΩ
must be short-circuited by fixing the EQ-switch input at the 70 µs position (pin 19; EQS left open-circuit). To activate
the inputs INA1 and INB1 pin 10 (HS) may be left open-circuit. In this event the DC level at pin 10 (HS) is 0.775 VCC.
General note
It is recommended to switch off VCC with a gradient of 400 V/s at maximum to avoid plops on tape in the event of contact
between tape and tape head while switching off.
August 1993
6
6 Page | |||
ページ | 合計 : 13 ページ | ||
|
PDF ダウンロード | [ TEA0677T データシート.PDF ] |
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
部品番号 | 部品説明 | メーカ |
TEA0677 | Dual pre-amplifier and equalizer for reverse tape decks | NXP Semiconductors |
TEA0677T | Dual pre-amplifier and equalizer for reverse tape decks | NXP Semiconductors |