DataSheet.jp

TL081 の電気的特性と機能

TL081のメーカーはNational Semiconductorです、この部品の機能は「WIDE BANDWIDTH JFET INPUT OPERATIONAL AMPLIFIER」です。


製品の詳細 ( Datasheet PDF )

部品番号 TL081
部品説明 WIDE BANDWIDTH JFET INPUT OPERATIONAL AMPLIFIER
メーカ National Semiconductor
ロゴ National Semiconductor ロゴ 




このページの下部にプレビューとTL081ダウンロード(pdfファイル)リンクがあります。

Total 8 pages

No Preview Available !

TL081 Datasheet, TL081 PDF,ピン配置, 機能
December 1995
TL081 Wide Bandwidth JFET
Input Operational Amplifier
General Description
The TL081 is a low cost high speed JFET input operational
amplifier with an internally trimmed input offset voltage
(BI-FET IITM technology) The device requires a low supply
current and yet maintains a large gain bandwidth product
and a fast slew rate In addition well matched high voltage
JFET input devices provide very low input bias and offset
currents The TL081 is pin compatible with the standard
LM741 and uses the same offset voltage adjustment circuit-
ry This feature allows designers to immediately upgrade the
overall performance of existing LM741 designs
The TL081 may be used in applications such as high speed
integrators fast D A converters sample-and-hold circuits
and many other circuits requiring low input offset voltage
low input bias current high input impedance high slew rate
and wide bandwidth The devices has low noise and offset
voltage drift but for applications where these requirements
Typical Connection
are critical the LF356 is recommended If maximum supply
current is important however the TL081C is the better
choice
Features
Y Internally trimmed offset voltage
Y Low input bias current
Y Low input noise voltage
Y Low input noise current
Y Wide gain bandwidth
Y High slew rate
Y Low supply current
Y High input impedance
Y Low total harmonic distortion AV e 10
RL e 10k VO e 20 Vp-p
BW e 20 Hzb20 kHz
Y Low 1 f noise corner
Y Fast settling time to 0 01%
15 mV
50 pA
25 nV 0Hz
0 01 pA 0Hz
4 MHz
13 V ms
1 8 mA
1012X
k0 02%
50 Hz
2 ms
Simplified Schematic
Connection Diagram
TL H 8358 – 1
Dual-In-Line Package
TL H 8358 – 2
BI-FET IITM is a trademark of National Semiconductor Corp
C1995 National Semiconductor Corporation TL H 8358
Order Number TL081CP
See NS Package Number N08E
TL H 8358 – 4
RRD-B30M125 Printed in U S A

1 Page





TL081 pdf, ピン配列
Typical Performance Characteristics
Input Bias Current
Input Bias Current
Supply Current
Positive Common-Mode Input
Voltage Limit
Negative Common-Mode Input
Voltage Limit
Positive Current Limit
Negative Current Limit
Voltage Swing
Output Voltage Swing
Gain Bandwidth
Bode Plot
Slew Rate
TL H 8358 – 5
3


3Pages


TL081 電子部品, 半導体
Application Hints (Continued)
common-mode range again puts the input stage and thus
the amplifier in a normal operating mode
Exceeding the positive common-mode limit on a single input
will not change the phase of the output however if both
inputs exceed the limit the output of the amplifier will be
forced to a high state
The amplifier will operate with a common-mode input volt-
age equal to the positive supply however the gain band-
width and slew rate may be decreased in this condition
When the negative common-mode voltage swings to within
3V of the negative supply an increase in input offset voltage
may occur
The TL081 is biased by a zener reference which allows nor-
mal circuit operation on g4V power supplies Supply volt-
ages less than these may result in lower gain bandwidth and
slew rate
The TL081 will drive a 2 kX load resistance to g10V over
the full temperature range of 0 C to a70 C If the amplifier
is forced to drive heavier load currents however an in-
crease in input offset voltage may occur on the negative
voltage swing and finally reach an active current limit on
both positive and negative swings
Precautions should be taken to ensure that the power sup-
ply for the integrated circuit never becomes reversed in po-
larity or that the unit is not inadvertently installed backwards
in a socket as an unlimited current surge through the
Detailed Schematic
resulting forward diode within the IC could cause fusing of
the internal conductors and result in a destroyed unit
Because these amplifiers are JFET rather than MOSFET
input op amps they do not require special handling
As with most amplifiers care should be taken with lead
dress component placement and supply decoupling in or-
der to ensure stability For example resistors from the out-
put to an input should be placed with the body close to the
input to minimize ‘‘pick-up’’ and maximize the frequency of
the feedback pole by minimizing the capacitance from the
input to ground
A feedback pole is created when the feedback around any
amplifier is resistive The parallel resistance and capaci-
tance from the input of the device (usually the inverting in-
put) to AC ground set the frequency of the pole In many
instances the frequency of this pole is much greater than
the expected 3 dB frequency of the closed loop gain and
consequently there is negligible effect on stability margin
However if the feedback pole is less than approximately 6
times the expected 3 dB frequency a lead capacitor should
be placed from the output to the input of the op amp The
value of the added capacitor should be such that the RC
time constant of this capacitor and the resistance it parallels
is greater than or equal to the original feedback pole time
constant
TL H 8358 – 8
6

6 Page



ページ 合計 : 8 ページ
 
PDF
ダウンロード
[ TL081 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
TL080

JFET-Input Operational Amplifier

Texas Instruments
Texas Instruments
TL081

TL081 Wide Bandwidth JFET Input Operational Amplifier (Rev. A)

Texas Instruments
Texas Instruments
TL081

GENERAL PURPOSE J-FET SINGLE OPERATIONAL AMPLIFIER

STMicroelectronics
STMicroelectronics
TL081

WIDE BANDWIDTH JFET INPUT OPERATIONAL AMPLIFIER

National Semiconductor
National Semiconductor


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap