DataSheet.jp

UTCUR3325 の電気的特性と機能

UTCUR3325のメーカーはUnisonic Technologiesです、この部品の機能は「LINEAR INTEGRATED CIRCUIT」です。


製品の詳細 ( Datasheet PDF )

部品番号 UTCUR3325
部品説明 LINEAR INTEGRATED CIRCUIT
メーカ Unisonic Technologies
ロゴ Unisonic Technologies ロゴ 




このページの下部にプレビューとUTCUR3325ダウンロード(pdfファイル)リンクがあります。
Total 6 pages

No Preview Available !

UTCUR3325 Datasheet, UTCUR3325 PDF,ピン配置, 機能
UTCUR3325 LINEAR INTEGRATED CIRCUIT
2 CHANNEL LOW-DROPOUT
VOLTAGE REGULATOR
FEATURES
*Dual Output: 3.3V/1A, 2.5V/1A.
*Output Voltage Precision of ±2%.
*Output consists of PNP power transistor with
low-dropout voltage.
*Built-in over current protection circuit (OCP).
*Built-in Thermal Shut Down Circuit (TSD).
*Ideal for Hard Disk Drives applications.
1
TO-252-5
1: Vcc 2: NC 3: GND 4: Vo1 5: VO2
PIN DISCRIPTION
PIN NO.
PIN NAME
1 Vcc
2 N.C.
3 GND
4 Vo1
5 Vo2
Power Supply
Not internally connected
Ground
3.3V Output
2.5V Output
FUNCTION
UTC
UNISONIC TECHNOLOGIES CO., LTD. 1
QW-R102-017,C

1 Page





UTCUR3325 pdf, ピン配列
UTCUR3325 LINEAR INTEGRATED CIRCUIT
ABSOLUTE MAXIMUM RATINGS (Ta=25)
PARAMETER
SYMBOL
Supply Voltage
Vcc
Power dissipation
PD
Operating temperature range
Topr
Storage temperature range
Tstg
Junction temperature
Tj
* PD derated at 8mW/for temperatures above Ta=25
RATINGS
18
1000*
-40 ~ +85
-55 ~ +150
150
UNIT
V
mW
°C
°C
°C
OPERATING RATINGS(Ta=25)
PARAMETER
Input Voltage
3.3V Output current
2.5V Output current
SYMBOL
Vcc
Io1
Io2
MIN
MAX
UNIT
3.0 16.0
V
1A
1A
ELECTRICAL CHARACTERISTICS
(Refer to the test circuit, Ta=25, VCC=5V unless otherwise specified.)
PARAMETER
SYMBOL TEST CONDITIONS
Bias Current
IB Io1=0mA, Io2=0mA
3.3V Output
Output Voltage 1
Dropout Voltage 1
Vo1 Io1=500mA
VD1 Io1=500mA, Vcc=3.135V
Peak Output Current 1
Io1
Ripple Rejection 1
Line Regulation 1
R.R.1
VLINE1
f=120Hz, ein=1Vrms
Io1=200mA
Vcc=4V ~ 16V, Io1=500mA
Load Regulation 1
Temperature Coefficient of Output
Voltage 1*
VLOAD1
TCVO1
Io1=0mA ~ 1A
Io1=5mA, TJ=0 ~ 125
Short circuit Output Current 1
IOS1 Vcc=16V
2.5V Output
Output Voltage 2
Vo2 Io2=500mA
Peak Output Current 2
Io2
Ripple Rejection 2
Line Regulation 2
Load Regulation 2
Temperature Coefficient of Output
Voltage 2*
R.R.2
VLINE2
VLOAD2
TCVO2
f=120Hz, ein=1Vrms
Io2=200mA
Vcc=4V ~ 16V, Io2=500mA
Io2=0mA ~ 1A
Io2=5mA, TJ=0 ~ 125
Short circuit Output Current 2
IOS2 Vcc=16V
* Design Guarantee. (Outgoing inspection is not done on all products.)
This product is not designed for protection against radioactive rays.
MIN TYP MAX UNIT
0.8 1.5 mA
3.234 3.30 3.366
0.25 0.5
1.0 1.7
50 58
5
30
±0.01
30
75
270
V
V
A
dB
mV
mV
%/
mA
2.450 2.50 2.550
1.0 1.7
50 58
5 30
30 75
±0.01
270
V
A
dB
mV
mV
%/
mA
Note: All characteristic are measured with a capacity across the input (0.33μF) and the output (22μF).
Measurement is done at TATJ, and variations in the parameter of all measurement (except for Temperature
Coefficient of Output Voltage)caused by temperature change are not considered.
UTC
UNISONIC TECHNOLOGIES CO., LTD. 3
QW-R102-017,C


3Pages


UTCUR3325 電子部品, 半導体
UTCUR3325 LINEAR INTEGRATED CIRCUIT
serially as ESR. For the bypass capacitor, a 0.33μF capacitor placed as close to Vcc pin and GND pin as possible
is recommended.
Over- current Protection Circuit
The over-current protection circuits are built in at the outputs. They protect the IC from being damaged when the
load is short-circuited or subjected to an over current condition. This protection circuits perform holdback current
limiting.
Thermal Protection Circuit
A thermal shut down circuit (T.S.D.) is built into the IC to prevent damage due to overheating, Therefore, all the
outputs are turned off when the T.S.D. circuit is activated and are turned on when the temperature recedes to the
specified level. However, the T.S.D. circuit is only for extreme conditions and the regulator circuit should still be
designed for the IC not to exceed TJ(max)=150.
Grounding
It is recommended that every capacitor (bypass and output capacitors) is grounded to PIN3 using single-point
connections.
Electromagnetic Fields
The IC is susceptible to strong electromagnetic fields and may cause malfunction. Therefore, caution should be
used when placing it on the PCB.
Protection Diodes
It is recommended that protection diodes be used when the output is connected to an inductive load.
UTC assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or
other parameters) listed in products specifications of any and all UTC products described or contained
herein. UTC products are not designed for use in life support appliances, devices or systems where
malfunction of these products can be reasonably expected to result in personal injury. Reproduction in
whole or in part is prohibited without the prior written consent of the copyright owner. The information
presented in this document does not form part of any quotation or contract, is believed to be accurate
and reliable and may be changed without notice.
UTC
UNISONIC TECHNOLOGIES CO., LTD. 6
QW-R102-017,C

6 Page



ページ 合計 : 6 ページ
 
PDF
ダウンロード
[ UTCUR3325 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
UTCUR3325

LINEAR INTEGRATED CIRCUIT

Unisonic Technologies
Unisonic Technologies


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap