DataSheet.jp

IR21844 の電気的特性と機能

IR21844のメーカーはInternational Rectifierです、この部品の機能は「HALF-BRIDGE DRIVER」です。


製品の詳細 ( Datasheet PDF )

部品番号 IR21844
部品説明 HALF-BRIDGE DRIVER
メーカ International Rectifier
ロゴ International Rectifier ロゴ 




このページの下部にプレビューとIR21844ダウンロード(pdfファイル)リンクがあります。

Total 8 pages

No Preview Available !

IR21844 Datasheet, IR21844 PDF,ピン配置, 機能
Data Sheet No. PD60174-D
IR2184(4)(S)
Features
Floating channel designed for bootstrap operation
Fully operational to +600V
Tolerant to negative transient voltage
dV/dt immune
Gate drive supply range from 10 to 20V
Undervoltage lockout for both channels
3.3V and 5V input logic compatible
Matched propagation delay for both channels
Logic and power ground +/- 5V offset.
Lower di/dt gate driver for better noise immunity
Output source/sink current capability 1.4A/1.8A
Description
HALF-BRIDGE DRIVER
Packages
14-Lead PDIP
IR21844
8-Lead SOIC
IR2184S
8-Lead PDIP
IR2184
14-Lead SOIC
IR21844S
The IR2184(4)(S) are high voltage,
high speed power MOSFET and IGBT
IR2181/IR2183/IR2184 Feature Comparison
drivers with dependent high and low
side referenced output channels. Pro-
prietary HVIC and latch immune
CMOS technologies enable rugge-
dized monolithic construction. The
logic input is compatible with standard
CMOS or LSTTL output, down to 3.3V
logic. The output drivers feature a high
Part
2181
21814
2183
21834
2184
21844
Input
logic
HIN/LIN
HIN/LIN
IN/SD
Cross-
conduction
prevention
logic
no
yes
yes
Dead-Time
Ground Pins
none
Internal 500ns
Program 0.4 ~ 5 us
Internal 500ns
Program 0.4 ~ 5 us
COM
VSS/COM
COM
VSS/COM
COM
VSS/COM
Ton/Toff
180/220 ns
180/220 ns
680/270 ns
pulse current buffer stage designed for
minimum driver cross-conduction. The floating channel can be used to drive an N-channel power MOSFET or
IGBT in the high side configuration which operates up to 600 volts.
Typical Connection
VCC
VCC
VB
IN IN HO
SD SD VS
COM
LO
IR2184
(Refer to Lead Assignments for correct
configuration). This/These diagram(s) show
electrical connections only. Please refer to
our Application Notes and DesignTips for
proper circuit board layout.
up to 600V
TO
LOAD
HO
VCC
VCC
VB
IN IN VS
SD SD
DT
VSS
VSS COM
RDT LO
IR21844
up to 600V
TO
LOAD
www.irf.com
1

1 Page





IR21844 pdf, ピン配列
IR2184(4) (S)
Dynamic Electrical Characteristics
VBIAS (VCC, VBS) = 15V, VSS = COM, CL = 1000 pF, TA = 25°C, DT = VSS unless otherwise specified.
Symbol
Definition
Min. Typ. Max. Units Test Conditions
ton
toff
tsd
MTon
Turn-on propagation delay
Turn-off propagation delay
Shut-down propagation delay
Delay matching, HS & LS turn-on
— 680 900
— 270 400
VS = 0V
VS = 0V or 600V
— 180 270
— 0 90 nsec
MToff Delay matching, HS & LS turn-off
— 0 40
tr
tf
DT
MDT
Turn-on rise time
— 40
Turn-off fall time
— 20
Deadtime: LO turn-off to HO turn-on(DTLO-HO) & 280 400
HO turn-off to LO turn-on (DTHO-LO)
4
5
Deadtime matching = DTLO - HO - DTHO-LO
—0
—0
60
35
520
6 µsec
50
nsec
600
VS = 0V
VS = 0V
RDT= 0
RDT = 200k
RDT=0
RDT = 200k
Static Electrical Characteristics
VBIAS (VCC, VBS) = 15V, VSS = COM, DT= VSS and TA = 25°C unless otherwise specified. The VIL, VIH and IIN
parameters are referenced to VSS /COM and are applicable to the respective input leads: IN and SD. The VO, IO and Ron
parameters are referenced to COM and are applicable to the respective output leads: HO and LO.
Symbol
VIH
VIL
VSD,TH+
VSD,TH-
VOH
VOL
ILK
IQBS
IQCC
IIN+
IIN-
VCCUV+
VBSUV+
VCCUV-
VBSUV-
VCCUVH
VBSUVH
IO+
Definition
Logic “1” input voltage for HO & logic “0” for LO
Logic “0” input voltage for HO & logic “1” for LO
SD input positive going threshold
SD input negative going threshold
High level output voltage, VBIAS - VO
Low level output voltage, VO
Offset supply leakage current
Quiescent VBS supply current
Quiescent VCC supply current
Logic “1” input bias current
Logic “0” input bias current
VCC and VBS supply undervoltage positive going
threshold
VCC and VBS dupply undervoltage negative going
threshold
Hysteresis
Output high short circuit pulsed vurrent
IO- Output low short circuit pulsed current
Min. Typ. Max. Units Test Conditions
2.7 — —
VCC = 10V to 20V
— — 0.8
VCC = 10V to 20V
2.7 — —
VCC = 10V to 20V
— — 0.8 V VCC = 10V to 20V
— — 1.2
IO = 0A
— — 0.1
IO = 0A
— — 50
VB = VS = 600V
µA
20 60 150
VIN = 0V or 5V
0.4 1.0 1.6 mA
VIN = 0V or 5V
— 5 20
IN = 5V, SD = 0V
µA
—1 2
IN = 0V, SD = 5V
8.0 8.9 9.8
7.4 8.2 9.0
0.3 0.7 —
V
1.4 1.9 —
1.8 2.3 —
A
VO = 0V,
PW 10 µs
VO = 15V,
PW 10 µs
www.irf.com
3


3Pages


IR21844 電子部品, 半導体
IR2184(4) (S)
8-Lead PDIP
01-6014
01-3003 01 (MS-001AB)
D
A5
6
E
8765
12 34
B
H
0.25 [.010]
A
F OOT PRINT
8X 0.72 [.028]
6.46 [.255]
6X e
e1
A
C
3X 1.27 [.050]
y
8X 1.78 [.070]
K x 45°
INCHES
DIM
MIN MAX
A .0532 .0688
A1 .0040 .0098
b .013 .020
c .0075 .0098
D .189 .1968
E .1497 .1574
e .050 BAS IC
e 1 .025 BAS IC
H .2284 .2440
K .0099 .0196
L .016 .050
y 0°
8°
MIL L IME T E RS
MIN MAX
1.35 1.75
0.10 0.25
0.33 0.51
0.19 0.25
4.80 5.00
3.80 4.00
1.27 BAS IC
0.635 BAS IC
5.80 6.20
0.25 0.50
0.40 1.27
0° 8°
8X b
A1
0.25 [.010] C A B
0.10 [.004]
8X L 8X c
7
NOT ES:
1. DIMENS IONING & T OLERANCING PE R ASME Y14.5M-1994.
2. CONT ROLLING DIMENSION: MILLIMET ER
3. DIMENS IONS ARE SHOWN IN MILLIME TE RS [INCHES].
4. OUT LINE CONF ORMS T O JEDEC OUTLINE MS-012AA.
8-Lead SOIC
5 DIMENSION DOES NOT INCLUDE MOLD PROT RUS IONS.
MOLD PROTRUSIONS NOT T O E XCEED 0.15 [.006].
6 DIMENSION DOES NOT INCLUDE MOLD PROT RUS IONS.
MOLD PROTRUSIONS NOT T O E XCEED 0.25 [.010].
7 DIMENSION IS T HE LE NGTH OF LEAD FOR SOLDE RING TO
A SUBS TRAT E.
01-6027
01-0021 11 (MS-012AA)
6 www.irf.com

6 Page



ページ 合計 : 8 ページ
 
PDF
ダウンロード
[ IR21844 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
IR2184

HALF-BRIDGE DRIVER

International Rectifier
International Rectifier
IR21844

HALF-BRIDGE DRIVER

International Rectifier
International Rectifier
IR21844PBF

HALF-BRIDGE DRIVER

International Rectifier
International Rectifier
IR21844S

HALF-BRIDGE DRIVER

International Rectifier
International Rectifier


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap