DataSheet.jp

ISL6431EVAL1 の電気的特性と機能

ISL6431EVAL1のメーカーはIntersil Corporationです、この部品の機能は「Advanced Pulse-Width Modulation (PWM) Controller for Home Gateways」です。


製品の詳細 ( Datasheet PDF )

部品番号 ISL6431EVAL1
部品説明 Advanced Pulse-Width Modulation (PWM) Controller for Home Gateways
メーカ Intersil Corporation
ロゴ Intersil Corporation ロゴ 




このページの下部にプレビューとISL6431EVAL1ダウンロード(pdfファイル)リンクがあります。
Total 10 pages

No Preview Available !

ISL6431EVAL1 Datasheet, ISL6431EVAL1 PDF,ピン配置, 機能
TM
Data Sheet
ISL6431
June 2001
File Number 9018
Advanced Pulse-Width Modulation (PWM)
Controller for Home Gateways
The ISL6431 is a high efficiency, fixed frequency,
synchronous buck PWM controller. It is designed for use in
applications that convert 5V to lower distributed voltages
required for set-top box, cable modem, DSL modem and
residential home gateway core processor, memory and
peripheral power supplies.
This device makes simple work out of implementing a
complete control and protection scheme for a DC-DC
stepdown converter. Designed to drive N-channel MOSFETs
in a synchronous buck topology, the ISL6431 integrates the
control, output adjustment, monitoring and protection
functions into a single 8-pin package.
The ISL6431 provides simple, single feedback loop, voltage-
mode control with fast transient response. The output
voltage can be precisely regulated to as low as 0.8V, with a
maximum tolerance of ±1.5% over temperature and line
voltage variations. A fixed frequency oscillator reduces
design complexity, while balancing typical application cost
and efficiency.
The error amplifier features a 15MHz gain-bandwidth
product and 6V/µs slew rate which enables high converter
bandwidth for fast transient performance. The resulting
PWM duty cycles range from 0% to 100%.
Protection from overcurrent conditions is provided by
monitoring the rDS(ON) of the upper MOSFET to inhibit PWM
operation appropriately. This approach simplifies the
implementation and improves efficiency by eliminating the
need for a current sense resistor.
Ordering Information
TEMP. RANGE
PART NUMBER
(oC)
PACKAGE
ISL6431CB
0 to 70 8 Ld SOIC
ISL6431IB
-40 to 85 8 Ld SOIC
ISL6431EVAL1
Evaluation Board
PKG.
NO.
M8.15
M8.15
Features
• Operates from +5V Input
• 0.8V to VIN Output Range
- 0.8V Internal Reference
- ±1.5% Over Line Voltage and Temperature
• Drives N-Channel MOSFETs
• Simple Single-Loop Control Design
- Voltage-Mode PWM Control
• Fast Transient Response
• Lossless, Programmable Overcurrent Protection
- Uses Upper MOSFET’s rDS(ON)
• Small Converter Size
- 300kHz Fixed Frequency Oscillator
- Internal Soft Start
- 8 Lead SOIC Package
• High Conversion Efficiency
• Synchronous/Standard Buck Configuration
Applications
• Cable Modems, Set Top Boxes, and DSL Modems
• DSP and Core Communications Processor Supplies
• Power Supplies for Microprocessors and Embedded
Controllers
• Memory Supplies
• Personal Computer Peripherals
• Industrial Power Supplies
• 5V-Input DC-DC Regulators
• Low-Voltage Distributed Power Supplies
Pinout
BOOT 1
UGATE 2
GND 3
LGATE 4
8 PHASE
7 COMP/OCSET
6 FB
5 VCC
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil and Design is a trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2001, All Rights Reserved

1 Page





ISL6431EVAL1 pdf, ピン配列
ISL6431
Absolute Maximum Ratings
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +6.0V
Absolute Boot Voltage, VBOOT . . . . . . . . . . . . . . . . . . . . . . . +15.0V
Upper Driver Supply Voltage, VBOOT - VPHASE . . . . . . . . . . . +6.0V
Input, Output or I/O Voltage . . . . . . . . . . . GND -0.3V to VCC +0.3V
ESD Classification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 2
Operating Conditions
Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . +5V ±10%
Ambient Temperature Range . . . . . . . . . . . . . . . . . . . -40oC to 85oC
Junction Temperature Range. . . . . . . . . . . . . . . . . . -40oC to 125oC
Thermal Information
Thermal Resistance (Typical, Note 1)
θJA (oC/W)
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . 150oC
Maximum Storage Temperature Range . . . . . . . . . . -65oC to 150oC
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300oC
(SOIC - Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θJA is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications Recommended Operating Conditions, Unless Otherwise Noted VCC = 5.0V±5% and TA = 25oC
PARAMETER
SYMBOL
TEST CONDITIONS
MIN TYP MAX
VCC SUPPLY CURRENT
Nominal Supply
IVCC
ISL6431CB; UGATE and LGATE Open
ISL6431IB; UGATE and LGATE Open
- 3.2 -
2.5 3.2 3.8
POWER-ON RESET
Rising VCC POR Threshold
POR
ISL6431CB
- 4.30 -
ISL6431IB
4.17 4.30 4.50
VCC POR Threshold
Hysteresis
ISL6431CB
ISL6431IB
- 0.20 -
0.01 0.20 0.85
OSCILLATOR
Frequency
fOSC
ISL6431CB; VCC = 5V
ISL6431IB; VCC = 5V
- 300 -
230 300 340
Ramp Amplitude
VOSC
ISL6431CB
ISL6431IB
- 1.5 -
- 1.5 -
REFERENCE
Reference Voltage Tolerance
ISL6431CB
- - 1.5
ISL6431IB
- - 1.5
Nominal Reference Voltage
VREF
ISL6431CB
ISL6431IB
- 0.800 -
- 0.800 -
ERROR AMPLIFIER
DC Gain
ISL6431CB
- 82 -
ISL6431IB
- 82 -
Gain-Bandwidth Product
GBWP ISL6431CB
14 -
-
ISL6431IB
14 -
-
Slew Rate
SR ISL6431CB; COMP = 10pF
- 8.0 -
ISL6431IB; COMP = 10pF
4.5 8.0 9.2
GATE DRIVERS
Upper Gate Source Current
IUGATE-SRC ISL6431CB; VBOOT - VPHASE = 5V, VUGATE = 4V
-
1.0
-
ISL6431IB; VBOOT - VPHASE = 5V, VUGATE = 4V
-
1.0
-
Upper Gate Sink Current
IUGATE-SNK ISL6431CB
- 1.0 -
ISL6431IB
- 1.0 -
Lower Gate Source Current
ILGATE-SRC ISL6431CB; VCC = 5V, VLGATE = 4V
ISL6431IB; VCC = 5V, VLGATE = 4V
- 1.0 -
- 1.0 -
UNITS
mA
mA
V
V
V
V
kHz
kHz
VP-P
VP-P
%
%
V
V
dB
dB
MHz
MHz
V/µs
V/µs
A
A
A
A
A
A
3


3Pages


ISL6431EVAL1 電子部品, 半導体
ISL6431
ISL6431
VIN
UGATE
PHASE
LGATE
Q1
Q2
LO VOUT
CIN
CO
RETURN
FIGURE 3. PRINTED CIRCUIT BOARD POWER AND
GROUND PLANES OR ISLANDS
Figure 3 shows the critical power components of the converter.
To minimize the voltage overshoot, the interconnecting wires
indicated by heavy lines should be part of a ground or power
plane in a printed circuit board. The components shown in
Figure 3 should be located as close together as possible.
Please note that the capacitors CIN and CO may each
represent numerous physical capacitors. Locate the ISL6431
within 3 inches of the MOSFETs, Q1 and Q2. The circuit traces
for the MOSFETs’ gate and source connections from the
ISL6431 must be sized to handle up to 1A peak current.
Figure 4 shows the circuit traces that require additional layout
consideration. Use single point and ground plane construction
for the circuits shown. Minimize any leakage current paths on
the COMP/OCSET pin and locate the resistor, ROSCET close
to the COMP/OCSET pin because the internal current source
is only 20µA. Provide local VCC decoupling between VCC and
GND pins. Locate the capacitor, CBOOT as close as practical
to the BOOT and PHASE pins. All components used for
feedback compensation should be located as close to the IC a
practical.
BOOT
D1
+5V CBOOT
ISL6431
PHASE
VCC
+5V
COMP/OCSET
CVCC
GND
+VIN
Q1 LO
Q2 CO
VOUT
FIGURE 4. PRINTED CIRCUIT BOARD SMALL SIGNAL
LAYOUT GUIDELINES
Feedback Compensation
Figure 5 highlights the voltage-mode control loop for a
synchronous-rectified buck converter. The output voltage
(VOUT) is regulated to the Reference voltage level. The
error amplifier (Error Amp) output (VE/A) is compared with
the oscillator (OSC) triangular wave to provide a pulse-
width modulated (PWM) wave with an amplitude of VIN at
the PHASE node. The PWM wave is smoothed by the output
filter (LO and CO).
OSC
PWM
COMPARATOR
VOSC
-
+
DRIVER
DRIVER
VIN
LO
PHASE CO
VOUT
ZFB
VE/A
-
+
ZIN
ERROR REFERENCE
AMP
ESR
(PARASITIC)
DETAILED COMPENSATION COMPONENTS
C2
C1 R2
ZFB
VOUT
ZIN
C3 R3
COMP
FB
-
+
ISL6431
REFERENCE
R1
FIGURE 5. VOLTAGE-MODE BUCK CONVERTER
COMPENSATION DESIGN
The modulator transfer function is the small-signal transfer
function of VOUT/VE/A . This function is dominated by a DC
Gain and the output filter (LO and CO), with a double pole
break frequency at FLC and a zero at FESR. The DC Gain of
the modulator is simply the input voltage (VIN) divided by the
peak-to-peak oscillator voltage VOSC.
Modulator Break Frequency Equations
FLC=
--------------------1---------------------
2π x LO x CO
FESR= -2---π------x-----E----S--1---R------x-----C-----O--
The compensation network consists of the error amplifier
(internal to the ISL6431) and the impedance networks ZIN
and ZFB. The goal of the compensation network is to provide
a closed loop transfer function with the highest 0dB crossing
frequency (f0dB) and adequate phase margin. Phase margin
is the difference between the closed loop phase at f0dB and
180 degrees. The equations below relate the compensation
network’s poles, zeros and gain to the components (R1, R2,
R3, C1, C2, and C3) in Figure 7. Use these guidelines for
locating the poles and zeros of the compensation network:
1. Pick Gain (R2/R1) for desired converter bandwidth.
2. Place 1ST Zero Below Filter’s Double Pole (~75% FLC).
3. Place 2ND Zero at Filter’s Double Pole.
4. Place 1ST Pole at the ESR Zero.
5. Place 2ND Pole at Half the Switching Frequency.
6

6 Page



ページ 合計 : 10 ページ
 
PDF
ダウンロード
[ ISL6431EVAL1 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
ISL6431EVAL1

Advanced Pulse-Width Modulation (PWM) Controller for Home Gateways

Intersil Corporation
Intersil Corporation
ISL6431EVAL1

Advanced Pulse Width Modulation (PWM) Controller for Broadband Applications

Intersil Corporation
Intersil Corporation


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap