|
|
PDF ISL4485 Data sheet ( Hoja de datos )
| Número de pieza | ISL4485 | |
| Descripción | 15kV ESD Protected/ 20Mbps/ 5V/ Low Power/ RS-485/RS-422 Transceiver | |
| Fabricantes | Intersil Corporation | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ISL4485 (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
®
Data Sheet
December 2003
ISL4485E
FN6049.1
±15kV ESD Protected, 20Mbps, 5V, Low
Power, RS-485/RS-422 Transceiver
The Intersil ISL4485E is a high speed, BiCMOS 5V
powered, single transceiver that meets both the RS-485 and
RS-422 standards for balanced communication. Each driver
output/receiver input is protected against ±15kV ESD
strikes, without latch-up. Unlike competitive devices, this
Intersil device is specified for 10% tolerance supplies (4.5V
to 5.5V).
The excellent differential output voltage coupled with high
drive-current output stages allow 20Mbps operation over
twisted pair networks up to 450 feet in length. The 25kΩ
receiver input resistance presents a “single unit load” to the
RS-485 bus, allowing up to 32 transceivers on the network.
Receiver (Rx) inputs feature a “fail-safe if open” design,
which ensures a logic high Rx output if Rx inputs are
floating.
Driver (Tx) outputs are short circuit protected, even for
voltages exceeding the power supply voltage. Additionally,
on-chip thermal shutdown circuitry disables the Tx outputs to
prevent damage if power dissipation becomes excessive.
The half duplex configuration multiplexes the Rx inputs and
Tx outputs to allow transceivers with Rx and Tx disable
functions in 8 lead packages.
Ordering Information
PART NO.
(BRAND)
ISL4485EIB
(4485EIB)
ISL4485EIB-T
(4485EIB)
TEMP.
RANGE (oC)
PACKAGE
-40 to 85 8 Ld SOIC
-40 to 85 8 Ld SOIC
Tape & Reel
PKG. DWG. #
M8.15
M8.15
Pinout
ISL4485E (SOIC)
TOP VIEW
RO 1
RE 2
DE 3
DI 4
R
D
8 VCC
7 B/Z
6 A/Y
5 GND
Features
• High Data Rates. . . . . . . . . . . . . . . . . . . . . up to 20Mbps
• RS-485 I/O Pin ESD Protection . . . . . . . . . . ±15kV HBM
- Class 3 ESD Level on all Other Pins . . . . . . >7kV HBM
• Operates from a Single +5V Supply (10% Tolerance)
• 1 Unit Load Allows up to 32 Devices on the Bus
• Low Quiescent Current . . . . . . . . . . . . . . . . . . . . . 590µA
• -7V to +12V Common Mode Input Voltage Range
• Three State Rx and Tx Outputs
• 30ns Propagation Delays, 2ns Skew
• Current Limiting and Thermal Shutdown for driver
Overload Protection
Applications
• SCSI “Fast 20” Drivers and Receivers
• Data Loggers
• Security Networks
• Building Environmental Control Systems
• Industrial/Process Control Networks
• Level Translators
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2003. All Rights Reserved.
All other trademarks mentioned are the property of their respective owners.
1 page  
ISL4485E
Test Circuits and Waveforms (Continued)
VCC
DE
DI
SIGNAL
GENERATOR
Z
D
Y
CL = 100pF
RDIFF
CL = 100pF
DI
OUT (Y)
OUT (Z)
1.5V
tPLH
50%
tPHL
50%
1.5V
3V
0V
tPHL
50%
VOH
VOL
tPLH
50%
VOH
VOL
DIFF OUT (Y - Z)
90%
10%
tR
90%
10%
tF
+VOD
-VOD
SKEW = |CROSSING PT. OF Y↑ & Z↓ - CROSSING PT. OF Y↓ & Z↑|
FIGURE 2A. TEST CIRCUIT
FIGURE 2B. MEASUREMENT POINTS
FIGURE 2. DRIVER PROPAGATION DELAY AND DIFFERENTIAL TRANSITION TIMES
DE
SIGNAL
GENERATOR
DI
Z
D
Y
CL
500Ω
VCC
SW GND
PARAMETER OUTPUT
tHZ Y/Z
tLZ Y/Z
tZH Y/Z
tZL Y/Z
RE
X
X
X
X
DI SW CL (pF)
1/0 GND
15
0/1 VCC
15
1/0 GND 100
0/1 VCC 100
DE
tZH
OUT (Y, Z)
tZL
OUT (Y, Z)
1.5V
1.5V
3V
0V
tHZ
OUTPUT HIGH
2.3V
VOH - 0.5V VOH
0V
tLZ
2.3V
OUTPUT LOW
VCC
VOL + 0.5V VOL
FIGURE 3A. TEST CIRCUIT
FIGURE 3B. MEASUREMENT POINTS
FIGURE 3. DRIVER ENABLE AND DISABLE TIMES
5
5 Page 
ISL4485E
Small Outline Plastic Packages (SOIC)
N
INDEX
AREA
E
-B-
H
0.25(0.010) M B M
123
-A-
D
SEATING PLANE
A
L
h x 45o
-C-
e A1
B
0.25(0.010) M C A M B S
µα
0.10(0.004)
C
NOTES:
1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
Publication Number 95.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
4. Dimension “E” does not include interlead flash or protrusions. Inter-
lead flash and protrusions shall not exceed 0.25mm (0.010 inch) per
side.
5. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater
above the seating plane, shall not exceed a maximum value of
0.61mm (0.024 inch).
10. Controlling dimension: MILLIMETER. Converted inch dimensions
are not necessarily exact.
M8.15 (JEDEC MS-012-AA ISSUE C)
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC
PACKAGE
INCHES
MILLIMETERS
SYMBOL MIN MAX MIN MAX NOTES
A
0.0532 0.0688 1.35
1.75
-
A1
0.0040 0.0098 0.10
0.25
-
B
0.013 0.020 0.33
0.51
9
C
0.0075 0.0098 0.19
0.25
-
D
0.1890 0.1968 4.80
5.00
3
E
0.1497 0.1574 3.80
4.00
4
e 0.050 BSC 1.27 BSC -
H
0.2284 0.2440 5.80
6.20
-
h
0.0099 0.0196 0.25
0.50
5
L
0.016 0.050 0.40
1.27
6
N8
87
α 0o 8o 0o 8o -
Rev. 0 12/93
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
11
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet ISL4485.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ISL4485 | 15kV ESD Protected/ 20Mbps/ 5V/ Low Power/ RS-485/RS-422 Transceiver | Intersil Corporation |
| ISL4485E | 15kV ESD Protected/ 20Mbps/ 5V/ Low Power/ RS-485/RS-422 Transceiver | Intersil Corporation |
| ISL4486 | 5V/ Ultra High Speed/ PROFIBUS/ RS-485/RS-422 Transceivers | Intersil Corporation |
| ISL4486IB | 5V/ Ultra High Speed/ PROFIBUS/ RS-485/RS-422 Transceivers | Intersil Corporation |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |