DataSheet.jp

ISP1106DH の電気的特性と機能

ISP1106DHのメーカーはNXP Semiconductorsです、この部品の機能は「Advanced Universal Serial Bus transceivers」です。


製品の詳細 ( Datasheet PDF )

部品番号 ISP1106DH
部品説明 Advanced Universal Serial Bus transceivers
メーカ NXP Semiconductors
ロゴ NXP Semiconductors ロゴ 




このページの下部にプレビューとISP1106DHダウンロード(pdfファイル)リンクがあります。

Total 24 pages

No Preview Available !

ISP1106DH Datasheet, ISP1106DH PDF,ピン配置, 機能
ISP1105/1106/1107
Advanced Universal Serial Bus transceivers
Rev. 06 — 30 November 2001
Product data
1. General description
The ISP1105/1106/1107 range of Universal Serial Bus (USB) transceivers are fully
compliant with the Universal Serial Bus Specification Rev. 1.1. They are ideal for
portable electronics devices such as mobile phones, digital still cameras, Personal
Digital Assistants (PDA) and Information Appliances (IA).
They allow USB Application Specific ICs (ASICs) and Programmable Logic Devices
(PLDs) with power supply voltages from 1.65 V to 3.6 V to interface with the physical
layer of the Universal Serial Bus. They have an integrated 5 V to 3.3 V voltage
regulator for direct powering via the USB supply VBUS.
The ISP1105/1106/1107 range can be used as a USB device transceiver or a USB
host transceiver. They can transmit and receive serial data at both full-speed
(12 Mbit/s) and low-speed (1.5 Mbit/s) data rates.
ISP1105 allows single/differential input modes selectable by a MODE input and it is
available in HBCC16 package. ISP1106 allows only differential input mode and is
available in both TSSOP16 and HBCC16 packages. ISP1107 allows only
single-ended input mode and is available in both TSSOP16 and HBCC16 packages.
2. Features
s Complies with Universal Serial Bus Specification Rev. 1.1
s Integrated bypassable 5 V to 3.3 V voltage regulator for powering via USB VBUS
s VBUS disconnection indication through VP and VM
s Used as a USB device transceiver or a USB host transceiver
s Supports full-speed (12 Mbit/s) and low-speed (1.5 Mbit/s) serial data rates
s Stable RCV output during SE0 condition
s Two single-ended receivers with hysteresis
s Low-power operation
s Supports an I/O voltage range from 1.65 V to 3.6 V
s 4 kV on-chip ESD protection
s Full industrial operating temperature range 40 to +85 °C
s Available in small TSSOP16 (except ISP1105) and HBCC16 packages.

1 Page





ISP1106DH pdf, ピン配列
Philips Semiconductors
5. Functional diagram
ISP1105/1106/1107
Advanced USB transceivers
VCC(I/O)
SOFTCON
OE
SPEED
VMO/FSE0(3)
VPO/VO(3)
MODE(4)
SUSPND
RCV
VP
3.3 V VOLTAGE
REGULATOR
LEVEL
SHIFTER
ISP1105
ISP1106
ISP1107
VCC(5.0)
Vreg(3.3)
Vpu(3.3)
D+ 33 (1) (1%)
D
33 (1) (1%)
1.5 k(2)
VM
GND
MBL301
(1) Use a 39 resistor (1%) for a USB v2.0 compliant output impedance range.
(2) Connect to Dfor low-speed operation.
(3) Pin function depends on device type see Section 7.2.
(4) Only for ISP1105.
Fig 1. Functional diagram (combined ISP1105, ISP1106 and ISP1107).
9397 750 08872
Product data
Rev. 06 — 30 November 2001
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
3 of 24


3Pages


ISP1106DH 電子部品, 半導体
Philips Semiconductors
ISP1105/1106/1107
Advanced USB transceivers
Table 3: Pin description…continued
Symbol[1] Pin
Type
ISP1105 ISP1106/7 ISP1106/7
HBCC16 HBCC16 TSSOP16
Vreg(3.3)
13
13
15
-
VCC(5.0)
14
14
16
-
Vpu(3.3)
15
15
1
-
Description
Internal regulator option: regulated supply voltage output
(3.0 to 3.6 V) during 5 V operation; a decoupling capacitor
of at least 0.1 µF is required
Regulator bypass option: used as a supply voltage input
for 3.3 V operation. (3.3 V ±10%)
Internal regulator option: supply voltage input
(4.0 to 5.5 V); can be connected directly to USB supply
VBUS
Regulator bypass option: connect to Vreg(3.3)
pull-up supply voltage (3.3 V ±10%); connect an external
1.5 kresistor on D+ (full-speed) or D(low-speed); pin
function is controlled by input SOFTCON:
SOFTCON 16 16 2
I
SOFTCON = LOW — Vpu(3.3) floating (high impedance);
ensures zero pull-up current
SOFTCON = HIGH — Vpu(3.3) = 3.3 V; internally connected
to Vreg(3.3)
software controlled USB connection input; a HIGH level
applies 3.3 V to pin Vpu(3.3), which is connected to an
external 1.5 kpull-up resistor; this allows USB
connect/disconnect signalling to be controlled by software
[1] Symbol names with an overscore (e.g. NAME) indicate active LOW signals.
[2] Down bonded to the exposed diepad.
7. Functional description
7.1 Function selection
Table 4: Function table
SUSPND OE
(D+, D)
L L driving &
receiving
L H receiving[1]
H L driving
RCV
active
active
inactive[2]
H H high-Z[1] inactive[2]
VP/VM
active
active
active
active
Function
normal driving
(differential receiver active)
receiving
driving during ‘suspend’[3]
(differential receiver inactive)
low-power state
[1] Signal levels on (D+, D−) are determined by other USB devices and external pull-up/down resistors.
[2] In ‘suspend’ mode (SUSPND = HIGH) the differential receiver is inactive and output RCV is always
LOW. Out-of-suspend (‘K’) signalling is detected via the single-ended receivers VP and VM.
[3] During suspend, the slew-rate control circuit of low-speed operation is disabled. The (D+, D−) lines
are still driven to their intended states, without slew-rate control. This is permitted because driving
during suspend is used to signal remote wake-up by driving a ‘K’ signal (one transition from idle to
‘K’ state) for a period of 1 to 15 ms.
9397 750 08872
Product data
Rev. 06 — 30 November 2001
© Koninklijke Philips Electronics N.V. 2001. All rights reserved.
6 of 24

6 Page



ページ 合計 : 24 ページ
 
PDF
ダウンロード
[ ISP1106DH データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
ISP1106DH

Advanced Universal Serial Bus transceivers

NXP Semiconductors
NXP Semiconductors


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap