|
|
PDF ISP1103 Data sheet ( Hoja de datos )
| Número de pieza | ISP1103 | |
| Descripción | Universal Serial Bus transceiver | |
| Fabricantes | NXP Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ISP1103 (archivo pdf) en la parte inferior de esta página. Total 17 Páginas | ||
|
No Preview Available !
ISP1103
Universal Serial Bus transceiver
Rev. 01 — 4 October 1999
Preliminary specification
1. General description
The ISP1103 is a single-chip generic Universal Serial Bus (USB) transceiver that is
fully compliant with the Universal Serial Bus Specification Rev. 1.1. It allows 3.3 V
USB Application Specific ICs (ASICs) and Programmable Logic Devices (PLDs) to
interface with the physical layer of the Universal Serial Bus. It supports transmitting
and receiving serial data at both full-speed (12 Mbit/s) and low-speed (1.5 Mbit/s)
data rates. It also supports the low-power single-ended input receiver interface in
‘suspend’ mode operation. The ISP1103 operates on a 3.3 V supply voltage.
The pin configuration conforms to the ‘Serial Interface Engine’ from the Universal
Serial Bus Implementers Forum (USB-IF). The ISP1103 allows for both the ‘USB-IF
Standard Data Interface’ and the ‘Philips Encoded Data Interface’. The ISP1103 is
fully pin compatible with the industry-standard Philips Semiconductors USB
transceiver PDIUSBP11A.
2. Features
s Complies with Universal Serial Bus Specification Rev. 1.1
s Supports full-speed (12 Mbit/s) and low-speed (1.5 Mbit/s) serial data rates
c
c
s Slew-rate controlled differential data driver
s Differential input receiver with wide common-mode range and very high data input
sensitivity
s Stable RCV output during SE0 condition
s Two single-ended receivers with hysteresis
s Supports ‘Philips Encoded Data Interface’ and ‘USB-IF Standard Data Interface’
s Low-power operation in ‘suspend’ mode
s Operates on a 3.3 V supply voltage
s Fully backward compatible with PDIUSBP11A
s Compatible with VHDL ‘Serial Interface Engine’ from USB Implementers Forum
s Higher than 8 kV ESD protection
s Full industrial operating temperature range −40 to +85 °C
s Available in SO14, SSOP14 and TSSOP14 packages.
1 page  
Philips Semiconductors
ISP1103
USB transceiver
7. Limiting values
Table 6: Absolute maximum ratings
In accordance with the Absolute Maximum Rating System (IEC 60134).
Symbol
Parameter
Conditions
VCC(3.3)
VI
Ilatchup
Vesd
Tstg
Ptot
supply voltage
input voltage
latchup current
electrostatic discharge voltage
storage temperature
total power dissipation
VI < 0 or VI > VCC
ILI < 1 µA
Min
−0.5
−0.5
-
[1] -
−60
-
[1] Equivalent to discharging a 100 pF capacitor via a 1.5 kΩ resistor (Human Body Model).
Max
+6.0
VCC + 0.5
200
±8000
+150
<tbf>
Unit
V
V
mA
V
°C
W
Table 7: Recommended operating conditions
Symbol
Parameter
VCC(3.3)
supply voltage
VI input voltage
VI(AI/O)
input voltage on analog I/O pins
(D+/D−)
Tamb
operating ambient temperature
Conditions
8. Static characteristics
Min Max Unit
3.0 3.6 V
0 5.5 V
0 3.6 V
−40 +85 °C
Table 8: Static characteristics: supply pins
VCC = VCC(3.3); VGND = 0 V; Tamb = −40 to +85 °C; unless otherwise specified.
Symbol
Parameter
Conditions
Min
ICC
ICC(susp)
operating supply current
suspend supply current
-
-
Typ
<tbf>
-
Max
-
10
Unit
mA
µA
9397 750 06329
Preliminary specification
Rev. 01 — 4 October 1999
© Philips Electronics N.V. 1999. All rights reserved.
5 of 17
5 Page 
Philips Semiconductors
SSOP14: plastic shrink small outline package; 14 leads; body width 5.3 mm
ISP1103
USB transceiver
SOT337-1
D
y
Z
14 8
c
EA
X
HE v M A
pin 1 index
1
e
7
bp
wM
A2
A1
Q
(A3)
A
Lp
L
detail X
θ
0 2.5 5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1) E (1)
e
HE
L
Lp
Q
v
w
y Z (1) θ
mm
2.0
0.21
0.05
1.80
1.65
0.25
0.38
0.25
0.20
0.09
6.4
6.0
5.4
5.2
0.65
7.9
7.6
1.25
1.03
0.63
0.9
0.7
0.2 0.13 0.1
1.4
0.9
8o
0o
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
OUTLINE
VERSION
IEC
REFERENCES
JEDEC
EIAJ
SOT337-1
MO-150AB
EUROPEAN
PROJECTION
ISSUE DATE
95-02-04
96-01-18
Fig 13. SSOP14 package outline.
9397 750 06329
Preliminary specification
Rev. 01 — 4 October 1999
© Philips Electronics N.V. 1999. All rights reserved.
11 of 17
11 Page | ||
| Páginas | Total 17 Páginas | |
| PDF Descargar | [ Datasheet ISP1103.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ISP1102 | Advanced Universal Serial Bus transceiver | NXP Semiconductors |
| ISP1102BS | Advanced Universal Serial Bus transceiver | NXP Semiconductors |
| ISP1102W | Advanced Universal Serial Bus transceiver | NXP Semiconductors |
| ISP1103 | Universal Serial Bus transceiver | NXP Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |