DataSheet.jp

4N30 の電気的特性と機能

4N30のメーカーはMotorola Incです、この部品の機能は「STANDARD THRU HOLE CASE 730A-04」です。


製品の詳細 ( Datasheet PDF )

部品番号 4N30
部品説明 STANDARD THRU HOLE CASE 730A-04
メーカ Motorola Inc
ロゴ Motorola  Inc ロゴ 




このページの下部にプレビューと4N30ダウンロード(pdfファイル)リンクがあります。

Total 6 pages

No Preview Available !

4N30 Datasheet, 4N30 PDF,ピン配置, 機能
MOTOROLA
SEMICONDUCTOR TECHNICAL DATA
GlobalOptoisolator
6-Pin DIP Optoisolators
Darlington Output
The 4N29/A, 4N30, 4N31, 4N32(1) and 4N33(1) devices consist of a gallium
arsenide infrared emitting diode optically coupled to a monolithic silicon
photodarlington detector.
This series is designed for use in applications requiring high collector output
currents at lower input currents.
Higher Sensitivity to Low Input Drive Current
Meets or Exceeds All JEDEC Registered Specifications
To order devices that are tested and marked per VDE 0884 requirements, the
suffix “V” must be included at end of part number. VDE 0884 is a test option.
Applications
Low Power Logic Circuits
Interfacing and coupling systems of different potentials and impedances
Telecommunications Equipment
Portable Electronics
Solid State Relays
MAXIMUM RATINGS (TA = 25°C unless otherwise noted)
Rating
Symbol
Value
Unit
INPUT LED
Reverse Voltage
Forward Current — Continuous
LED Power Dissipation @ TA = 25°C
Derate above 25°C
VR 3 Volts
IF 60 mA
PD 120 mW
1.41 mW/°C
OUTPUT DETECTOR
Collector–Emitter Voltage
Emitter–Collector Voltage
Collector–Base Voltage
Collector Current — Continuous
Detector Power Dissipation @ TA = 25°C
Derate above 25°C
VCEO
VECO
VCBO
IC
PD
30 Volts
5 Volts
30 Volts
150 mA
150 mW
1.76 mW/°C
TOTAL DEVICE
Isolation Surge Voltage(2)
(Peak ac Voltage, 60 Hz, 1 sec Duration)
VISO
7500
Vac(pk)
Total Device Power Dissipation @ TA = 25°C
Derate above 25°C
PD 250 mW
2.94 mW/°C
Ambient Operating Temperature Range(3)
Storage Temperature Range(3)
TA – 55 to +100
Tstg – 55 to +150
°C
°C
Soldering Temperature (10 sec, 1/16from case)
TL 260 °C
1. Difference in 4N32 and 4N33 is JEDEC Registration for VISO only. All Motorola 6–Pin devices
exceed JEDEC specification and are 7500 Vac(pk). The same applies for 4N29 and 4N30.
2. Isolation surge voltage is an internal device dielectric breakdown rating. For this test, Pins 1 and
2 are common, and Pins 4, 5 and 6 are common.
3. Refer to Quality and Reliability Section in Opto Data Book for information on test conditions.
Preferred devices are Motorola recommended choices for future use and best overall value.
GlobalOptoisolator is a trademark of Motorola, Inc.
REV 4
© MMoototroorlao,lIancO. 1p9t9o5electronics Device Data
Order this document
by 4N29/D
4N29
4N29A
4N30 *
[CTR = 100% Min]
4N31
[CTR = 50% Min]
4N32 *
4N33 *
[CTR = 500% Min]
*Motorola Preferred Devices
STYLE 1 PLASTIC
6
1
STANDARD THRU HOLE
CASE 730A–04
SCHEMATIC
16
25
34
PIN 1. LED ANODE
2. LED CATHODE
3. N.C.
4. EMITTER
5. COLLECTOR
6. BASE
1

1 Page





4N30 pdf, ピン配列
2
PULSE ONLY
1.8 PULSE OR DC
1.6
4N29 4N29A 4N30 4N31 4N32 4N33
TYPICAL CHARACTERISTICS
10
NORMALIZED TO: IF = 10 mA
TA = 25°C
1
1.4
TA = –55°C
1.2
25°C
1 100°C
1 10
100
IF, LED FORWARD CURRENT (mA)
1000
Figure 1. LED Forward Voltage versus Forward Current
0.1
TA = –55°C THRU
+25°C
+70°C
+100°C
0.01
0.5 1
2
5 10 20
50
IF, LED INPUT CURRENT (mA)
Figure 2. Output Current versus Input Current
140
120
IF = 10 mA
100
80
5 mA
60
40
2 mA
20
1 mA
0
0 1 2 3 4 5 6 7 8 9 10
VCE, COLLECTOR–EMITTER VOLTAGE (VOLTS)
Figure 3. Collector Current versus
Collector–Emitter Voltage
10
7
5 NORMALIZED TO TA = 25°C
2
1
0.7
0.5
0.2
0.1
–60 –40 –20 0 20 40 60 80 100
TA, AMBIENT TEMPERATURE (°C)
Figure 4. Output Current versus Ambient Temperature
1.3
NORMALIZED TO TA = 25°C
1.2
1.1
1
0.9
0.8
0.7
–60 –40 –20 0 20 40 60 80 100
TA, AMBIENT TEMPERATURE (°C)
Figure 5. Collector–Emitter Voltage versus
Ambient Temperature
105
104 NORMALIZED TO: VCE = 10 V
NORMALIZED TO: TA = 25°C
103
102
30 V
10
10 V
1
0 20 40 60 80 100
TA, AMBIENT TEMPERATURE (°C)
Figure 6. Collector–Emitter Dark Current versus
Ambient Temperature
Motorola Optoelectronics Device Data
3


3Pages


4N30 電子部品, 半導体
4N29 4N29A 4N30 4N31 4N32 4N33
–A–
64
–B–
13
F 4 PL
–T–
SEATING
PLANE
E 6 PL
N
C
L
GK
D 6 PL
0.13 (0.005) M T A M
BM
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
INCHES
MILLIMETERS
DIM MIN MAX MIN MAX
A 0.320 0.350 8.13 8.89
B 0.240 0.260 6.10 6.60
C 0.115 0.200 2.93 5.08
D 0.016 0.020 0.41 0.50
E 0.040 0.070 1.02 1.77
F 0.010 0.014 0.25 0.36
G 0.100 BSC
2.54 BSC
J 0.008 0.012 0.21 0.30
K 0.100 0.150 2.54 3.81
L 0.400 0.425 10.16 10.80
J N 0.015 0.040 0.38 1.02
*Consult factory for leadform
option availability
CASE 730D–05
ISSUE D
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,
and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different
applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does
not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in
systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of
the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us:
USA / EUROPE: Motorola Literature Distribution;
P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447
JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,
6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315
MFAX: [email protected] – TOUCHTONE (602) 244–6609 HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://Design–NET.com
51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
6
*4N29/D*Motorola Optoelectronics Dev4icNe29D/Data

6 Page



ページ 合計 : 6 ページ
 
PDF
ダウンロード
[ 4N30 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
4N30

STANDARD THRU HOLE CASE 730A-04

Motorola  Inc
Motorola Inc
4N30

PHOTO TRANSISTOR (AC LINE/DIGITAL LOGIC ISOLATOR)

Toshiba Semiconductor
Toshiba Semiconductor
4N30

GENERAL PURPOSE 6-PIN PHOTODARLINGTON OPTOCOUPLERS

QT Optoelectronics
QT Optoelectronics
4N30

(4N30 - 4N3) General Purpose 6-Pin Photodarlington Optocoupler

Fairchild Semiconductor
Fairchild Semiconductor


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap