DataSheet.jp

5962R9563101TEC の電気的特性と機能

5962R9563101TECのメーカーはIntersil Corporationです、この部品の機能は「Radiation Hardened Quad Differential Line Receiver」です。


製品の詳細 ( Datasheet PDF )

部品番号 5962R9563101TEC
部品説明 Radiation Hardened Quad Differential Line Receiver
メーカ Intersil Corporation
ロゴ Intersil Corporation ロゴ 




このページの下部にプレビューと5962R9563101TECダウンロード(pdfファイル)リンクがあります。
Total 3 pages

No Preview Available !

5962R9563101TEC Datasheet, 5962R9563101TEC PDF,ピン配置, 機能
Data Sheet
HS-26CT32RH-T
July 1999 File Number 4593.1
Radiation Hardened
Quad Differential Line Receiver
Intersil’s Satellite Applications FlowTM (SAF) devices are fully
tested and guaranteed to 100kRAD total dose. These QML
Class T devices are processed to a standard flow intended
to meet the cost and shorter lead-time needs of large
volume satellite manufacturers, while maintaining a high
level of reliability.
The Intersil HS-26CT32RH-T is a Quad Differential Line
Receiver designed for digital data transmission over
balanced lines and meets the requirements of EIA Standard
RS-422. Radiation Hardened CMOS processing assures low
power consumption, high speed, and reliable operation in
the most severe radiation environments.
The HS-26CT32RH-T has an input sensitivity of 200mV (typ.)
over the common mode input voltage range of ±7V. The
receivers are also equipped with input fail safe circuitry, which
causes the outputs to go to a logic “1” when the inputs are
open. TTL compatible Enable and Disable functions are
common to all four receivers.
Specifications
Specifications for Rad Hard QML devices are controlled by
the Defense Supply Center in Columbus (DSCC). The SMD
numbers listed below must be used when ordering.
Detailed Electrical Specifications for the HS-26CT32RH-T
are contained in SMD 5962-95631. A “hot-link” is provided
from our website for downloading.
www.intersil.com/spacedefense/newsafclasst.asp
Intersil’s Quality Management Plan (QM Plan), listing all
Class T screening operations, is also available on our
website.
www.intersil.com/quality/manuals.asp
Ordering Information
ORDERING
NUMBER
PART
NUMBER
TEMP.
RANGE (oC)
5962R9563101TEC
HS1-26CT32RH-T
-55 to 125
HS1-26CT32RH/Proto HS1-26CT32RH/Proto -55 to 125
5962R9563101TXC
HS9-26CT32RH-T
-55 to 125
HS9-26CT32RH/Proto HS9-26CT32RH/Proto -55 to 125
NOTE: Minimum order quantity for -T is 150 units through
distribution, or 450 units direct.
Features
• QML Class T, Per MIL-PRF-38535
• Radiation Performance
- Gamma Dose . . . . . . . . . . . . . . . . . . . . 1 x 105 RAD(Si)
- SEU and SEL . . . . . . . . . . Immune to 100MeV/mg/cm2
• EIA RS-422 Compatible Inputs
• TTL Compatible Enable Inputs
• Input Fail Safe Circuitry
• High Impedance Inputs when Disabled or Powered Down
• Low Power Dissipation 138mW Standby (Max)
• Single 5V Supply
• Full -55oC to 125oC Military Temperature Range
Pinouts
HS1-26CT32RH-T (SBDIP) CDIP2-T16
TOP VIEW
AIN 1
AIN 2
AOUT 3
ENABLE 4
COUT 5
CIN 6
CIN 7
GND 8
16 VDD
15 BIN
14 BIN
13 BOUT
12 ENABLE
11 DOUT
10 DIN
9 DIN
HS9-26CT32RH-T (FLATPACK), CDFP4-F16
TOP VIEW
AIN
AIN
AOUT
ENABLE
COUT
CIN
CIN
GND
1 16
2 15
3 14
4 13
5 12
6 11
7 10
89
VDD
BIN
BIN
BOUT
ENABLE
DOUT
DIN
DIN
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
Satellite Applications Flow™ (SAF) is a trademark of Intersil Corporation.

1 Page





5962R9563101TEC pdf, ピン配列
HS-26CT32RH-T
Die Characteristics
DIE DIMENSIONS:
2140µm x 3290µm x 533µm ±25.4µm
(85 x 130 x 21mils ±1mil)
METALLIZATION:
M1: Mo/Tiw
Thickness: 5800Å
M2: Al/Si/Cu
Thickness: 10kÅ ±1kÅ
SUBSTRATE POTENTIAL:
Internally connected to VDD. May be left floating.
BACKSIDE FINISH:
Silicon
PASSIVATION:
Type: SiO2
Thickness: 8kÅ ±1kÅ
WORST CASE CURRENT DENSITY:
< 2.0e5 A/cm2
TRANSISTOR COUNT:
315
PROCESS:
Radiation Hardened CMOS, AVLSI
Metallization Mask Layout
HS-26CT32RH-T
AIN
VDD
BIN
(1) (16) (15)
AIN (2)
(14) BIN
AOUT (3)
ENAB (4)
(13) BOUT
(12) ENAB
COUT (5)
(11) DOUT
CIN (6)
(10) DIN
(7) (8) (9)
CIN
GND
DIN
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time with-
out notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
3


3Pages





ページ 合計 : 3 ページ
 
PDF
ダウンロード
[ 5962R9563101TEC データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
5962R9563101TEC

Radiation Hardened Quad Differential Line Receiver

Intersil Corporation
Intersil Corporation


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap