DataSheet.jp

E5530H-232-DIT の電気的特性と機能

E5530H-232-DITのメーカーはATMEL Corporationです、この部品の機能は「128-bit Read-only IDIC for RF Identification」です。


製品の詳細 ( Datasheet PDF )

部品番号 E5530H-232-DIT
部品説明 128-bit Read-only IDIC for RF Identification
メーカ ATMEL Corporation
ロゴ ATMEL Corporation ロゴ 




このページの下部にプレビューとE5530H-232-DITダウンロード(pdfファイル)リンクがあります。
Total 8 pages

No Preview Available !

E5530H-232-DIT Datasheet, E5530H-232-DIT PDF,ピン配置, 機能
Features
Low-power, Low-voltage CMOS
Rectifier, Voltage Limiter, Clock Extraction On-chip (No Battery)
Small Size
Factory Laser Programmable ROM
Operating Temperature Range -40°C to +125°C
Radio Frequency (RF): 100 kHz to 450 kHz
Transmission options
– Code Length: 128, 96, 64, 32 bits
– Bitrate [bit/s]: RF/8, RF/16, RF/32, RF/40, RF/50, RF/64, RF/80, RF/100, RF/128
– Modulation: FSK, PSK, BIPH, Manchester, BIPH-FSK
FDX-B Compatible Coding Possible (ISO 11784/ ISO 11785)
Figure 1. Application
RF transmitter
and
interrogator
IDIC
RF e5530
ID
128-bit
Read-only
IDICfor RF
Identification
e5530
Description
The e5530 is part of a closed coupled identification system. It receives power from an
RF transmitter which is coupled inductively to the IDIC. The frequency is typically
100 kHz to 450 kHz. Receiving RF, the IDICresponds with a data stream by
damping the incoming RF via an internal load. This damping-in-turn can be detected
by the interrogator. The identifying data are stored in a 128-bit PROM on the e5530,
realized as an array of laser-programmable fuses. The logic block diagram for the
e5530 is shown in figure 2. The data are output bit-serially as a code of length
128, 96, 64 or 32 bits. The chips are factory-programmed with a unique code.
Figure 2. Block Diagram
Analog front end
Load
Mod
Coil
Modulator
FSK
PSK
BIPH
Manchester
Clock
extractor
Clk
Data
R7
R6
R5
R4
R3
R2
R1
R0
128-bit PROM
Coil
Rectifier
VDD VSS
Bitrate
Column decoder
Counter
Rev. 4508BRFID02/02
1

1 Page





E5530H-232-DIT pdf, ピン配列
e5530
FSK Modulation
Logical data 1and 0are represented as two different frequencies of damping. The
frequency for 1is RF divided by 10, a 0divides RF by 8.
PSK Modulation
The external coil is damped with a carrier frequency of RF/2. A logical 1causes (at the
end of the bit period) a 180° phase shift on the carrier frequency, while a logical 0
causes no phase shift.
Biphase Modulation
Logical 1produces a signal which is the same as the internal bitclock. A logical 0
produces no signal change in the middle of the bit period.
Manchester Modulation
A logical 1causes a rising edge in the middle of a bit period (i.e., switch damping off),
while a logical 0causes a falling edge (i.e., switch damping on).
A combination of Biphase- and FSK-modulation is also optionally available. The
available combinations between the modulation types and the bitrates are shown in
Table 1 Transmission Options.
Table 1. Transmission Options
Modulation Carrier Frequency (CF) Bitrate [bit/s]
FSK RF/8, RF/10
RF/32, RF/40, RF/50, RF/64, RF/80, RF/100,
RF/128
PSK
RF/2
CF/4, 8, 16, 32
Biphase
RF/8, RF/16, RF/32, RF/64, RF/100, RF/128
Manchester
RF/8, RF/16, RF/32, RF/64, RF/100, RF/128
Figure 5. Timing Diagram for Modulation Options
BitClk
Data
1011001
FSK
PSK
Man
Biph
4508BRFID02/02
3


3Pages


E5530H-232-DIT 電子部品, 半導体
Electrical Characteristics
Tamb = 25°C, reference terminal is VDD, operating voltage VDD - VSS = 3 V DC, unless otherwise specified
No. Parameters
Test Conditions
Symbol Min. Typ. Max.
1
2
3
4
5
Note:
Operating voltage
Condition for logic test
Operating temperature
Input frequency (RF)
Operating current
Clamp voltage
fCLK = 125 kHz, VSS = -2 V
I = 4 mA
1. Typical parameters represent the statistical mean values
VSS
Tamb
fCLK
ICC
VCL
-1.5 -5.0
-40 125
100 450
3 (1)
6.7 10
Unit
V
°C
kHz
mA
V
Figure 8. Measurement Setup for IDD
I DD
VDD
Coil 1
~ = 2V
Coil 2
VSS
Vpp Coil @1.5 V
Figure 9. Simplified Damping Circuit
100
Coil 1
~2V
Coil 2
100
~2V
Mod
Application Example
Figure 10. Typical Application Circuit
From
oscillator
IAC
125 kHz
740 µH
Energy
To read
amplifier
Data
2.2 nF
4.05 mH 390 pF
Input capacitance
5 pF static, 4 pF
dynamic
Coil1 (Pin 8)
e5530
(SO8)
Coil2 (Pin 1)
6 e5530
4508BRFID02/02

6 Page



ページ 合計 : 8 ページ
 
PDF
ダウンロード
[ E5530H-232-DIT データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
E5530H-232-DIT

128-bit Read-only IDIC for RF Identification

ATMEL Corporation
ATMEL Corporation
E5530H-232-DIT

128-Bit IDIC for Radio Frequency Identification

TEMIC Semiconductors
TEMIC Semiconductors


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap