LZ2315A Datasheet PDF - Sharp Electrionic Components
| Part Number | LZ2315A | |
| Description | Dual-power-supply (5 V/12 V) Operation 1/3-type CCD Area Sensors with 270 k Pixels | |
| Manufacturers | Sharp Electrionic Components | |
| Logo |  |
|
|
There is a preview and LZ2315A download ( pdf file ) link at the bottom of this page. Total 14 Pages | ||
Preview 1 page No Preview Available !
LZ2315A/LZ2316AR
LZ2315A/
LZ2316AR
Dual-power-supply (5 V/12 V) Operation
1/3-type CCD Area Sensors with 270 k Pixels
DESCRIPTION
The LZ2315A/LZ2316AR are 1/3-type (6.0 mm)
solid-state image sensors that consist of PN photo-
diodes and CCDs (charge-coupled devices) driven
by dual-power-supply. With approximately 270 000
pixels (542 horizontal x 492 vertical), the sensor
provides a stable high-resolution color (LZ2315A)/
B/W (LZ2316AR) normal or mirror image.
FEATURES
• Number of effective pixels : 512 (H) x 492 (V)
• Number of optical black pixels
– Horizontal : 2 front and 28 rear
• Pixel pitch : 9.6 µm (H) x 7.5 µm (V)
• Mg, G, Cy, and Ye complementary color filters
(For LZ2315A)
• Low fixed-pattern noise and lag
• No burn-in and no image distortion
• Blooming suppression structure
• Built-in output amplifier
• Built-in pulse mix circuit
• Built-in overflow drain voltage circuit and reset
gate voltage circuit
• Variable electronic shutter (1/60 to 1/10 000 s)
• Normal or mirror image output available from
common output pin
• Compatible with NTSC standard (LZ2315A)/
EIA standard (LZ2316AR)
• Package :
16-pin shrink-pitch WDIP [Ceramic]
(WDIP016-N-0500C)
Row space : 12.70 mm
PIN CONNECTIONS
16-PIN SHRINK-PITCH WDIP
TOP VIEW
ØRS 1
RD 2
GND 3
OS 4
OD 5
ØH2B 6
ØH2 7
ØH1B 8
16 T1
15 OFD
14 ØTG
13 ØV2
12 ØV1
11 ØV4
10 ØV3
9 ØH1
(WDIP016-N-0500C)
PRECAUTIONS
• The exit pupil position of lens should be more
than 25 mm (LZ2315A)/20 mm (LZ2316AR) from
the top surface of the CCD.
• Refer to "PRECAUTIONS FOR CCD AREA
SENSORS" for details.
COMPARISON TABLE
TV standard
Characteristics
LZ2315A
LZ2316AR
NTSC standard (Color)
EIA standard (B/W)
Refer to each following specification.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in
catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
1
|
| |
 
LZ2315A/LZ2316AR
CHARACTERISTICS FOR LZ2316AR (Drive method : Field accumulation)
(TA = +25 ˚C, Operating conditions : The typical values specified in "RECOMMENDED OPERATING CONDITIONS".
Color temperature of light source : 3 200 K, IR cut-off filter (CM-500, 1 mmt) is used.)
PARAMETER
SYMBOL
MIN. TYP. MAX. UNIT NOTE
Standard output voltage
VO 150 mV 2
Photo response non-uniformity
PRNU
15 %
3
Saturation output voltage
VSAT
650
mV 4
Dark output voltage
VDARK
0.5 mV 1, 5
Dark signal non-uniformity
DSNU
0.5 mV 1, 6
Sensitivity
R
700 1 000
mV 7
Smear ratio
SMR
–110 –90 dB
8
Image lag
AI
1.0 %
9
Blooming suppression ratio
ABL 1 000
10
Output transistor drain current
IOD 4.0 8.0 mA
Output impedance
RO 400 $
NOTES :
• Within the recommended operating conditions of VOD,
VOFD of the internal output satisfies with ABL larger than
1 000 times exposure of the standard exposure conditions,
and VSAT larger than 650 mV.
1. TA = +60 ˚C
2. The average output voltage under uniform illumination.
The standard exposure conditions are defined as when
Vo is 150 mV.
3. The image area is divided into 10 x 10 segments under
the standard exposure conditions. Each segment's
voltage is the average output voltage of all pixels within
the segment. PRNU is defined by (Vmax – Vmin)/Vo,
where Vmax and Vmin are the maximum and minimum
values of each segment's voltage respectively.
4. The image area is divided into 10 x 10 segments. Each
segment's voltage is the average output voltage of all
pixels within the segment. VSAT is the minimum
segment's voltage under 10 times exposure of the
standard exposure conditions.
5. The average output voltage under non-exposure
conditions.
6. The image area is divided into 10 x 10 segments under
non-exposure conditions. DSNU is defined by (Vdmax –
Vdmin), where Vdmax and Vdmin are the maximum and
minimum values of each segment's voltage respectively.
7. The average output voltage when a 1000 lux light
source with a 90% reflector is imaged by a lens of F4,
f50 mm.
8. The sensor is exposed only in the central area of V/10
square with a lens at F4, where V is the vertical image
size. SMR is defined by the ratio of the output voltage
detected during the vertical blanking period to the
maximum output voltage in the V/10 square.
9. The sensor is exposed at the exposure level
corresponding to the standard conditions. AI is defined
by the ratio of the output voltage measured at the 1st
field during the non-exposure period to the standard
output voltage.
10. The sensor is exposed only in the central area of V/10
square, where V is the vertical image size. ABL is
defined by the ratio of the exposure at the standard
conditions to the exposure at a point where blooming is
observed.
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for LZ2315A electronic component. |
| Information | Total 14 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ LZ2315A.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| LZ2315A | The function is Dual-power-supply (5 V/12 V) Operation 1/3-type CCD Area Sensors with 270 k Pixels. Sharp Electrionic Components | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
LZ23
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||