DataSheet.jp

HS-1135RH の電気的特性と機能

HS-1135RHのメーカーはIntersil Corporationです、この部品の機能は「Radiation Hardened/ High Speed/ Low Power Current Feedback Amplifier with Programmable Output Limiting」です。


製品の詳細 ( Datasheet PDF )

部品番号 HS-1135RH
部品説明 Radiation Hardened/ High Speed/ Low Power Current Feedback Amplifier with Programmable Output Limiting
メーカ Intersil Corporation
ロゴ Intersil Corporation ロゴ 




このページの下部にプレビューとHS-1135RHダウンロード(pdfファイル)リンクがあります。
Total 5 pages

No Preview Available !

HS-1135RH Datasheet, HS-1135RH PDF,ピン配置, 機能
Data Sheet
HS-1135RH
August 1999 File Number 4099.2
Radiation Hardened, High Speed, Low
Power Current Feedback Amplifier with
Programmable Output Limiting
The HS-1135RH is a radiation hardened, high speed, low
power current feedback amplifier built with Intersil’s
proprietary complementary bipolar UHF-1 (DI bonded wafer)
process. They are QML approved and processed in full
compliance with MIL-PRF-38535. This amplifier features
user programmable output limiting, via the VH and VL pins.
The HS-1135RH is the ideal choice for high speed, low
power applications requiring output limiting (e.g., flash A/D
drivers), especially those requiring fast overdrive recovery
times. The limiting function allows the designer to set the
maximum and minimum output levels to protect downstream
stages from damage or input saturation. The sub-
nanosecond overdrive recovery time ensures a quick return
to linear operation following an overdrive condition.
Component and composite video systems also benefit from
this op amp’s performance, as indicated by the gain flatness,
and differential gain and phase specifications.
Specifications for Rad Hard QML devices are controlled
by the Defense Supply Center in Columbus (DSCC). The
SMD numbers listed here must be used when ordering.
Detailed Electrical Specifications for these devices are
contained in SMD 5962-96767. A “hot-link” is provided
on our homepage for downloading.
http://www.intersil.com/spacedefense/space.htm
Ordering Information
ORDERING NUMBER
INTERNAL
MKT. NUMBER
TEMP. RANGE
(oC)
5962F9676701VPA
HS7-1135RH-Q
-55 to 125
5962F9676701VPC
HS7B-1135RH-Q
-55 to 125
HS7-1135RH/PROTO HS7-1135RH/PROTO -55 to 125
Features
• Electrically Screened to SMD # 5962-96767
• QML Qualified per MIL-PRF-38535 Requirements
• User Programmable Output Voltage Limiting
• Fast Overdrive Recovery . . . . . . . . . . . . . . . . . <1ns (Typ)
• Low Supply Current . . . . . . . . . . . . . . . . . . . . 6.9mA (Typ)
• Wide -3dB Bandwidth. . . . . . . . . . . . . . . . . .360MHz (Typ)
• High Slew Rate. . . . . . . . . . . . . . . . . . . . . .1200V/µs (Typ)
• High Input Impedance . . . . . . . . . . . . . . . . . . . 2M(Typ)
• Excellent Gain Flatness (to 50MHz). . . . . . ±0.07dB (Typ)
• Total Gamma Dose. . . . . . . . . . . . . . . . . . . . 300kRAD(Si)
• Latch Up . . . . . . . . . . . . . . . . . . . . . None (DI Technology)
Applications
• Flash A/D Driver
• Video Switching and Routing
• Pulse and Video Amplifiers
• Wideband Amplifiers
• RF/IF Signal Processing
• Imaging Systems
Pinout
HS-1135RH
GDIP1-T8 (CERDIP)
OR CDIP2-TI (SBDIP)
TOP VIEW
NC 1
-IN 2
+IN 3
V- 4
-
+
8 VH
7 V+
6 OUT
5 VL
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999

1 Page





HS-1135RH pdf, ピン配列
HS-1135RH
subnanosecond recovery time. The difference between the
unclamped and clamped propagation delays is the overdrive
recovery time. The appropriate propagation delays are 4.0ns
for the unclamped pulse, and 4.8ns for the clamped (2X
overdrive) pulse yielding an overdrive recovery time of
800ps. The measurement uses the 90% point of the output
transition to ensure that linear operation has resumed. Note:
The propagation delay illustrated is dominated by the
fixturing. The delta shown is accurate, but the true
HS-1135RH propagation delay is 500ps.
Use of Die in Hybrid Applications
This amplifier is designed with compensation to negate the
package parasitics that typically lead to instabilities. As a
result, the use of die in hybrid applications results in
overcompensated performance due to lower parasitic
capacitances. Reducing RF below the recommended values
for packaged units will solve the problem. For AV = +2 the
recommended starting point is 300, while unity gain
applications should try 400.
PC Board Layout
The frequency performance of this amplifier depends a great
deal on the amount of care taken in designing the PC board.
The use of low inductance components such as chip
resistors and chip capacitors is strongly recommended,
while a solid ground plane is a must!
Attention should be given to decoupling the power supplies.
A large value (10µF) tantalum in parallel with a small value
chip (0.1µF) capacitor works well in most cases.
Terminated microstrip signal lines are recommended at the
input and output of the device. Output capacitance, such as
that resulting from an improperly terminated transmission
line will degrade the frequency response of the amplifier and
may cause oscillations. In most cases, the oscillation can be
avoided by placing a resistor in series with the output.
Care must also be taken to minimize the capacitance to
ground seen by the amplifier’s inverting input. The larger this
capacitance, the worse the gain peaking, resulting in pulse
overshoot and possible instability. To this end, it is
recommended that the ground plane be removed under
traces connected to pin 2, and connections to pin 2 should
be kept as short as possible.
An example of a good high frequency layout is the
Evaluation Board shown in Figure 2.
Evaluation Board
An evaluation board is available for the HS-1135RH,
(HFA11XXEVAL). Please contact your local sales office for
information.
The layout and schematic of the board are shown here:
VH
1
+IN
OUT V+
VL V-
GND
FIGURE 2A. TOP LAYOUT
FIGURE 2B. BOTTOM LAYOUT
500
50
IN
10µF 0.1µF
500
1
2
3
4
-5V
VH
8
7
6
5
GND
0.1µF
50
10µF
+5V
OUT
VL
GND
FIGURE 2C. SCHEMATIC
FIGURE 2. EVALUATION BOARD SCHEMATIC AND LAYOUT
3


3Pages





ページ 合計 : 5 ページ
 
PDF
ダウンロード
[ HS-1135RH データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
HS-1135RH

Radiation Hardened/ High Speed/ Low Power Current Feedback Amplifier with Programmable Output Limiting

Intersil Corporation
Intersil Corporation


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap