|
|
AT-233PINのメーカーはTyco Electronicsです、この部品の機能は「Digital Attenuator/ 30 dB/ 4-Bit/ TTL Driver/ DC - 2 GHz」です。 |
部品番号 | AT-233PIN |
| |
部品説明 | Digital Attenuator/ 30 dB/ 4-Bit/ TTL Driver/ DC - 2 GHz | ||
メーカ | Tyco Electronics | ||
ロゴ | |||
このページの下部にプレビューとAT-233PINダウンロード(pdfファイル)リンクがあります。 Total 3 pages
Digital Attenuator, 30 dB, 4-Bit,
TTL Driver, DC - 2 GHz
V 3.00
Features
n Attenuation: 2 dB Steps to 30 dB 2
n Temperature Stability: ± 0.18 dB from –55°C to +85°C
Typical
n Low DC Power Consumption
n Hermetic Surface Mount Package
n Integral TTL Driver
n 50 Ohm Nominal Impedance
Description
M/A-COM’s AT-233 is a GaAs FET 4-Bit digital
attenuator with a 2 dB minimum step size and 30 dB total
attenuation. This attenuator and integral TTL driver is in a
hermetically sealed ceramic 16-lead surface mount package.
The AT-233 is ideally suited for use where accuracy, fast
switching, very low power consumption and low
intermodulation products are required. Typical applications
include dynamic range setting in precision receiver circuits
and other gain/leveling control circuits. Environmental
screening is available. Contact the factory for information.
CR-12
Electrical Specifications: TA = 25°C1
Parameter
Reference Insertion Loss
Test Conditions
Attenuation Accuracy3
Any Single Bit
Any Combination of Bits
VSWR
Trise, Tfall
Ton, Toff
Transients
1 dB Compression 4
Input IP3 4
Input IP2 4
10% to 90%
50% Control to 90/10% RF
In-Band (peak-peak)
Input Power
For two tone input power
Up to +5 dBm
For two-tone input power
Up to +5 dBm
Frequency Units
Min
Typ
Max
DC - 0.5 GHz
DC - 1.0 GHz
DC - 2.0 GHz
dB
dB
dB
—
—
—
— 2.3
— 2.65
— 2.8
DC - 1.0 GHz
DC - 2.0 GHz
DC - 1.0 GHz
DC - 2.0 GHz
± (0.2 + 3% of attenuation setting in dB) dB
± (0.2 + 3% of attenuation setting in dB) dB
or ± 0.45 dB, whichever is greater
± (0.20 + 3% of attenuation setting in dB) dB
± (0.25 + 4% of attenuation setting in dB) dB
or ± 0.45 dB, whichever is greater
DC - 2.0 GHz Ratio
—
— 1.7:1
— ns — 10 —
— ns — 30 —
— mV — 35 —
0.05 GHz
dBm
—
+20
—
0.5 - 2.0 GHz dBm
—
+28
—
0.05 GHz
dBm
—
+40
—
0.5 - 2.0 GHz dBm
—
+50
—
0.05 GHz
dBm
—
+45
—
0.5 - 2.0 GHz dBm
—
+68
—
1. All specifications apply when operated with bias voltages of +5V or VCC and –5.0V to –8.0V for VEE, and 50 Ohm impedance at
all ports unless otherwise specified.
2. Above reference insertion loss.
3. This attenuator is guaranteed monotonic.
4. VEE = -5V for the typical numbers given.
1 Page Digital Attenuator, 30 dB, 4-Bit, TTL Driver, DC - 2 GHz
Typical Performance Curves
AT-233
V 3.00
Ref. Insertion Loss vs. Frequency
+85°C
+25°C -55°C
5.0
4.0
3.0
2.0
1.0
0.0
0.0
0.5 1.0 1.5
Frequency (GHz)
2.0
VSWR vs. Frequency
2 dB 4 dB 8 dB 16 dB Ref Loss State
2.00
1.80
1.60
1.40
1.20
1.00
0.0
0.5 1.0 1.5
Frequency (GHz)
2.0
Attenuation Accuracy vs. Frequency
Full Atten
1.0
16 dB
8 dB
4 dB
0.5
0.0
-0.5
-1.0
-1.5
-2.0
0.0
0.5 1.0 1.5
Frequency (GHz)
2 dB
2.0
Ordering Information 6
Part Number
AT-233 PIN
Package
CR-12
6. Contact the factory for standard or custom screening
requirements
Specifications subject to change without notice.
n North America: Tel. (800) 366-2266
n Asia/Pacific: Tel.+81-44-844-8296, Fax +81-44-844-8298
n Europe: Tel. +44 (1344) 869 595, Fax+44 (1344) 300 020
Visit www.macom.com for additional data sheets and product information.
3
3Pages | |||
ページ | 合計 : 3 ページ | ||
|
PDF ダウンロード | [ AT-233PIN データシート.PDF ] |
データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。 |
部品番号 | 部品説明 | メーカ |
AT-233PIN | Digital Attenuator/ 30 dB/ 4-Bit/ TTL Driver/ DC - 2 GHz | Tyco Electronics |