|
|
PDF A2106A Data sheet ( Hoja de datos )
| Número de pieza | A2106A | |
| Descripción | solid state crowbar devices | |
| Fabricantes | Teccor Electronics | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de A2106A (archivo pdf) en la parte inferior de esta página. Total 2 Páginas | ||
|
No Preview Available !
Balanced Three-chip SIDACtor Device
Balanced Three-chip SIDACtor Device
The three-chip modified TO-220 SIDACtor balanced solid state device is designed for
1 3 telecommunication protection systems that reference Tip and Ring to earth ground.
Applications include any piece of transmission equipment that requires balanced protection.
This device is built using Teccor’s patented “Y” (US Patent 4,905,119) configuration.
2
The SIDACtor device is used to enable equipment to meet various regulatory requirements
including GR 1089, ITU K.20,K.21 and K.45, IEC 60950, UL 60950, and TIA-968 (formerly
known as FCC Part 68).
Electrical Parameters
Part
Number *
P1553A_
P1803A_
P2103A_
P2353A_
P2703A_
P3203A_
P3403A_
P5103A_
A2106A_3 **
A5030A_3 **
VDRM
Volts
VS
Volts
Pins 1-2, 2-3
130 180
150 210
170 250
200 270
230 300
270 350
300 400
420 600
170 250
400 550
VDRM
Volts
VS
Volts
Pins 1-3
VT
Volts
IDRM
µAmps
130 180
8
5
150 210
8
5
170 250
8
5
200 270
8
5
230 300
8
5
270 350
8
5
300 400
8
5
420
50
600 8
5
www.DataSheet4U.com
80 8
5
270 340
8
5
IS
mAmps
800
800
800
800
800
800
800
800
800
800
IT
Amps
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
2.2
IH
mAmps
150
150
150
150
150
150
150
150
120
150
CO
pF
40
40
40
40
30
30
30
30
40
30
* For individual “AA”, “AB”, and “AC” surge ratings, see table below.
** Asymmetrical
General Notes:
• All measurements are made at an ambient temperature of 25 °C. IPP applies to -40 °C through +85 °C temperature range.
• IPP is a repetitive surge rating and is guaranteed for the life of the product.
• Listed SIDACtor devices are bi-directional. All electrical parameters and surge ratings apply to forward and reverse polarities.
• VDRM is measured at IDRM.
• VS is measured at 100 V/µs.
• Special voltage (VS and VDRM) and holding current (IH) requirements are available upon request.
• Off-state capacitance is measured between Pins 1-2 and 3-2 at 1 MHz with a 2 V bias and is a typical value for “AA” product. “AB”
and “AC” capacitance is approximately 2x the listed value.
• Device is designed to meet balance requirements of GTS 8700 and GR 974.
Surge Ratings
Series
A
B
C
IPP
2x10 µs
Amps
150
250
500
IPP
8x20 µs
Amps
150
250
400
IPP
10x160 µs
Amps
90
150
200
IPP
10x560 µs
Amps
50
100
150
IPP
10x1000 µs
Amps
45
80
100
ITSM
60 Hz
Amps
20
30
50
di/dt
Amps/µs
500
500
500
http://www.teccor.com
+1 972-580-7777
2 - 34
© 2003 Teccor Electronics
SIDACtor® Data Book and Design Guide
1 page | ||
| Páginas | Total 2 Páginas | |
| PDF Descargar | [ Datasheet A2106A.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| A2106A | solid state crowbar devices | Teccor Electronics |
| A2106U | solid state crowbar devices | Teccor Electronics |
| A2106Z | solid state crowbar devices | Teccor Electronics |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |