DataSheet.jp

A1143LUA の電気的特性と機能

A1143LUAのメーカーはAllegro MicroSystemsです、この部品の機能は「Sensitive Two-Wire Chopper-Stabilized Unipolar Hall-Effect Switches」です。


製品の詳細 ( Datasheet PDF )

部品番号 A1143LUA
部品説明 Sensitive Two-Wire Chopper-Stabilized Unipolar Hall-Effect Switches
メーカ Allegro MicroSystems
ロゴ Allegro MicroSystems ロゴ 




このページの下部にプレビューとA1143LUAダウンロード(pdfファイル)リンクがあります。

Total 11 pages

No Preview Available !

A1143LUA Datasheet, A1143LUA PDF,ピン配置, 機能
A1140/41/42/43
Sensitive Two-Wire Chopper-Stabilized
Unipolar Hall-Effect Switches
Package LH, 3-pin SOT
3
1. VCC
2. No connection
3. GND
NC
12
Package UA, 3-pin SIP
1. VCC
2. GND
3. GND
PTCT
123
ABSOLUTE MAXIMUM RATINGS
Supply Voltage, VCC .......................................... 28 V
Reverse-Supply Voltage, VRCC ........................ –18 V
Magnetic Flux Density, B .........................Unlimited
Operating Temperature
Ambient, TA, Range E.................. –40ºC to 85ºC
Ambient, TA, Range L................ –40ºC to 150ºC
Maximum Junction, TJ(max)........................165ºC
Storage Temperature, TS .................. –65ºC to 170ºC
The A1140, A1141, A1142, and A1143 devices are sensitive, two-wire, unipo-
lar, Hall effect switches that are factory-programmed at end-of-line to optimize
magnetic switchpoint accuracy. These devices are produced on the Allegro
MicroSystems advanced BiCMOS wafer fabrication process, which implements a
patented, high-frequency, chopper-stabilization technique that achieves magnetic
stability and eliminates the offsets that are inherent in single-element devices
exposed to harsh application environments. Commonly found in a number of
automotive applications, the A1140-43 family of devices are utilized to sense: seat
track position, seat belt buckle presence, hood/trunk latching, and shift selector
position.
Two-wire unipolar switches are particularly advantageous in price-sensitive appli-
cations, because they require one less wire than the more traditional open-collec-
tor output switches. Additionally, the system designer gains inherent diagnostics
because output current normally ows in either of two narrowly-specied ranges.
Any output current level outside of these two ranges is a fault condition. The
A1140-43 family of devices also features on-chip transient protection, and a Zener
clamp to protect against overvoltage conditions on the supply line.
The output currents of the A1141 and A1143 switch HIGH in the presence of a south
polarity magnetic eld of sufcient strength; and switch LOW otherwise, including
when there is no signicant magnetic eld present. The A1140 and A1142 have
inverted output current levels: switching LOW in the presence of a south polarity
magnetic eld of sufcient strength, and HIGH otherwise. The devices also differ in
their specied LOW current supply levels.
All family members are offered in two package styles: SOT-23W, a miniature low-
prole package for surface-mount applications (sufx –LH), and TO-92, three-
lead ultra-mini Single Inline Package (SIP) for through-hole mounting
(sufx –UA).
Field-programmable versions are also available. Refer to: A1180, A1181, A1182,
and A1183.
Features and Benets
Chopper stabilization
Low switchpoint drift over operating tem-
perature range
Low stress sensitivity
Factory programmed at end-of-line for
optimized switchpoints
On-chip protection
Supply transient protection
Reverse-battery protection
On-board voltage regulator
3.5 V to 24 V operation
A1140-DS
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com

1 Page





A1143LUA pdf, ピン配列
A1140/41/42/43
Sensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches
ELECTRICAL CHARACTERISTICS over the operating voltage and temperature range, unless otherwise specied
Characteristic
Symbol
Test Conditions
Min. Typ. Max. Units
Supply Voltage
VCC Device powered on
3.5 – 24 V
Supply Current1
Zener Clamp Supply Voltage
ICC(L)
ICC(H)
VZ(supply)
B >BOP for A1140; B <BRP for A1141
B >BOP for A1142; B <BRP for A1143
B >BOP for A1141, A1143
B <BRP for A1140, A1142
ICC = ICC(max) + 3 mA; TA = 25°C
2 – 5 mA
5 – 6.9 mA
12 – 17 mA
28 – 40 V
Zener Clamp Supply Current2
Output Slew Rate3
IZ(supply)
di/dt
VZ(supply) = 28 V
No bypass capacitor; capacitance of the
oscilloscope performing the measurement
= 20 pF
– 10 mA
36 – mA/µs
Chopping Frequency
fC
– 400 – kHz
Power-On Time4
ton
After factory programming; with and without
bypass capacitor (CBYP = 0.01 µF)
– 25 µs
Power-On State5
POS
ton ton(max); VCC slew rate 25 mV/µs
– HIGH –
1Relative values of B use the algebraic convention, where positive values indicate south magnetic polarity, and negative values indicate north magnetic
polarity; therefore greater B values indicate a stronger south polarity eld (or a weaker north polarity eld, if present).
2The maximum value for IZ(supply) is equal to ICC(L)MAX + 3 mA.
3The value of di is the difference between 90% of ICC(H) and 10% of ICC(L), and the value of dt is time period between those two points. The value of di/dt
depends on the value of the bypass capacitor, if one is used, with greater capacitances resulting in lower rates of change.
45TAhVeCvCasluleewofratoten
depends on the value of the bypass capacitor, if
less than 25 mV/µs affects device performance,
one is used, with greater capacitances resulting in
both while powering-on and while running. For ton
longer ton.
> ton(max), and
BRP
<
B
<
BOP,
POS
is undened.
MAGNETIC CHARACTERISTICS* over the operating voltage and temperature range, unless otherwise specied
Characteristic
Symbol
Test Conditions
Min. Typ. Max. Units
Operate Point
Release Point
BOP
ICC(H) ICC(L) for A1140, A1142
ICC(L) ICC(H) for A1141, A1143
BRP
ICC(L) ICC(H) for A1140, A1142
ICC(H) ICC(L) for A1141, A1143
50 85 115 G
45 – 110 G
Hysteresis
BHYS
BHYS = BOP – BRP
5 15 30 G
*Relative values of B use the algebraic convention, where positive values indicate south magnetic polarity, and negative values indicate north magnetic
polarity; therefore greater B values indicate a stronger south polarity eld (or a weaker north polarity eld, if present).
A1140-DS
Allegro MicroSystems, Inc.
3
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com


3Pages


A1143LUA 電子部品, 半導体
A1140/41/42/43
Sensitive Two-Wire Chopper-Stabilized Unipolar Hall Effect Switches
Functional Description
Operation
The output, ICC, of the A1140 and A1142 devices switch low
after the magnetic eld at the Hall sensor exceeds the oper-
ate point threshold, BOP. When the magnetic eld is reduced to
below the release point threshold, BRP, the device output goes
high. The differences between the magnetic operate and release
point is called the hysteresis of the device, BHYS. This built-
in hysteresis allows clean switching of the output even in the
presence of external mechanical vibration and electrical noise.
The A1141 and A1143 devices switch with opposite polarity for
similar BOP and BRP values, in comparison to the A1140 and
A1142 (see gure 1).
I+
ICC(H)
I+
ICC(H)
0
B–
ICC(L)
B+
0
B–
ICC(L)
B+
BHYS
(A) A1140, A1142
BHYS
(B) A1141, A1143
Figure 1. Alternative switching behaviors are available in the A114x device family. On the horizontal axis, the B+ direction indicates
increasing south polarity magnetic eld strength, and the B– direction indicates decreasing south polarity eld strength (including the
case of increasing north polarity).
A1140-DS
Allegro MicroSystems, Inc.
6
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com

6 Page



ページ 合計 : 11 ページ
 
PDF
ダウンロード
[ A1143LUA データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
A1143LUA

Sensitive Two-Wire Chopper-Stabilized Unipolar Hall-Effect Switches

Allegro MicroSystems
Allegro MicroSystems


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap