DataSheet.jp

AD53040 の電気的特性と機能

AD53040のメーカーはAnalog Devicesです、この部品の機能は「Ultrahigh Speed Pin Driver」です。


製品の詳細 ( Datasheet PDF )

部品番号 AD53040
部品説明 Ultrahigh Speed Pin Driver
メーカ Analog Devices
ロゴ Analog Devices ロゴ 




このページの下部にプレビューとAD53040ダウンロード(pdfファイル)リンクがあります。

Total 7 pages

No Preview Available !

AD53040 Datasheet, AD53040 PDF,ピン配置, 機能
a
FEATURES
500 MHz Driver Operation
Driver Inhibit Function
100 ps Edge Matching
Guaranteed Industry Specifications
50 Output Impedance
>1.5 V/ns Slew Rate
Variable Output Voltages for ECL, TTL and CMOS
High Speed Differential Inputs for Maximum Flexibility
Ultrasmall 20-Lead SOP Package with Built-In Heat Sink
APPLICATIONS
Automatic Test Equipment
Semiconductor Test Systems
Board Test Systems
Instrumentation and Characterization Equipment
Ultrahigh Speed Pin Driver
with Inhibit Mode
AD53040
FUNCTIONAL BLOCK DIAGRAM
VCC VCC
VEE
VEE
VH
DATA
DATA
INH
INH
VL
DRIVER
AD53040
50
1.0A/K
39nF
39nF
VHDCPL
VOUT
VLDCPL
TVCC
THERM
GND GND GND GND GND
PRODUCT DESCRIPTION
The AD53040 is a complete high speed pin driver designed for
use in digital or mixed-signal test systems. Combining a high
speed monolithic process with a unique surface mount package,
this product attains superb electrical performance while preserv-
ing optimum packaging densities and long-term reliability in an
ultrasmall 20-lead, SOP package with built-in heat sink.
Featuring unity gain programmable output levels of –3 V to
+8 V, with output swing capability of less than 100 mV to 9 V,
the AD53040 is designed to stimulate ECL, TTL and CMOS
logic families. The 500 MHz data rate capacity and matched
output impedance allows for real-time stimulation of these
digital logic families. To test I/O devices, the pin driver can
be switched into a high impedance state (Inhibit Mode), electri-
cally removing the driver from the path. The pin driver leakage
current inhibit is typically 100 nA and output charge transfer
entering inhibit is typically less than 20 pC.
The AD53040 transition from HI/LO or to inhibit is controlled
through the data and inhibit inputs. The input circuitry uses
high speed differential inputs with a common-mode range of
± 3 V. This allows for direct interface to precision differential
ECL timing or the simplicity of stimulating the pin driver from a
single ended TTL or CMOS logic source. The analog logic HI/LO
inputs are equally easy to interface. Typically requiring 10 µA of
bias current, the AD53040 can be directly coupled to the
output of a digital-to-analog converter.
The AD53040 is available in a 20-lead, SOP package with a
built-in heat sink and is specified to operate over the ambient
commercial temperature range of –25°C to +85°C.
REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700 World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 1999

1 Page





AD53040 pdf, ピン配列
Parameter
DYNAMIC PERFORMANCE, DRIVE
(VH and VL) (Continued)
Minimum Pulsewidth
3 V Swing
5 V Swing
Toggle Rate
Min Typ Max
Units
1.7 ns
2.6 ns
500 MHz
DYNAMIC PERFORMANCE, INHIBIT
Delay Time, Active to Inhibit
2
5 ns
Delay Time, Inhibit to Active
2 5 ns
I/O Spike
Output Capacitance
<200
5
POWER SUPPLIES
Total Supply Range
Positive Supply
Negative Supply
Positive Supply Current
Negative Supply Current
Total Power Dissipation
Temperature Sensor Gain Factor
19
+12
–7
75
75
1.15 1.43
1.0
NOTES
Connecting or shorting the decoupling capacitors to ground will result in the destruction of the device.
Specifications subject to change without notice.
mV, p-p
pF
V
V
V
mA
mA
W
µA/K
Test Conditions
AD53040
4.0 ns Input, 10%/90% Output,
VL = 0 V, VH = 3 V
6.0 ns Input, 10%/90% Output,
VL = 0 V, VH = 5 V
VL = –1.8 V, VH = –0.8 V,
VOUT > 600 mV p-p
Measured at 50%, VH = +2 V,
VL = –2 V
Measured at 50%, VH = +2 V,
VL = –2 V
VH = 0 V, VL = 0 V
Driver Inhibited
RLOAD = 10 K, VSOURCE = +12 V
ABSOLUTE MAXIMUM RATINGS1
Power Supply Voltage
+VS to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +13 V
–VS to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –8 V
+VS to –VS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +20 V
Inputs
DATA, DATA, INH, INH . . . . . . . . . . . . . . . . +5 V, –3 V
DATA to DATA, INH to INH . . . . . . . . . . . . . . . . . . ± 3 V
VH, VL to GND . . . . . . . . . . . . . . . . . . . . . . . . . +9 V, –4 V
VH to VL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +11 V, 0 V
Outputs
VOUT Short Circuit Duration . . . . . . . . . . . . . . . . Indefinite2
VOUT Range in Inhibit Mode
VHDCPL . . . . . Do Not Connect Except for Capacitor to VCC
VLDCPL . . . . . Do Not Connect Except for Capacitor to VEE
THERM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +13 V, 0 V
Environmental
Operating Temperature (Junction) . . . . . . . . . . . . . . +175°C
Storage Temperature . . . . . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 10 sec)3 . . . . . . . . . . +260°C
NOTES
1Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Absolute maximum limits apply
individually, not in combination. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
2Output short circuit protection is guaranteed as long as proper heat sinking is
employed to ensure compliance with the operating temperature limits.
3To ensure lead coplanarity (± 0.002 inches) and solderability, handling with bare
hands should be avoided and the device should be stored in environments at 24°C
± 5°C (75°F ± 10°F) with relative humidity not to exceed 65%.
ORDERING GUIDE
Model
Package
Description
Shipment Method,
Quantity Per
Package
Shipping Container Option
AD53040KRP 20-Lead Power SOIC Tube, 38 Pieces
RP-20
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD53040 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. B
–3–


3Pages


AD53040 電子部品, 半導体
AD53040
DATA
J1
SMB
50
R6
50
C12
0.01F
U1
1 8 MC10EL16
27
36
5
–5.2V
C21
0.1F
R4 R3
5050
SMB
J4
SMB
J3
–2V
C14
0.1F
INH
J2
SMB
50
R5
50
C13
0.01F
U2
1 MC10EL16
2
8
7
36
5
–5.2V
C22
0.1F
R1
50
R2
50
SMB
J5
SMB
J6
–2V
C15
0.1F
P1
1
9
2
10
3
11
4
12
5
13
6
14
7
15
8
50
NOTE:
1. 50TERMINATION TO BE AS CLOSE TO RECEIVER
AS POSSIBLE. (END OF TRACE MARKED BY *). THROUGH
SMA CONNECTS BETWEEN MC10EL16 OUTPUTS AND DUT.
2. NO VIAS ALLOWED ON VOUT LINE.
3. SMA ON VOUT TO BE MOUNTED ON ITS SIDE FOR BEST
IMPEDANCE MATCH.
4. ONE DIMENSION OF BOARD TO BE 4-1/2 INCHES.
5. DUT PACKAGE IS TO BE CENTERED ON BOARD.
6. ALL RESISTORS AND NONELECTROLYTIC CAPS ARE
0805-SIZE SURFACE MOUNT.
7. SEE DATA SHEET FOR HIDDEN POWER AND GROUND PINS
ON LOGIC GATES.
VLOW
8. ALL 100nF BYPASS CAPACITORS TO BE LOCATED CLOSE
TO PACKAGE.
VHIGH
9. PCB IS TO BE 4-LAYER WITH POWER GND ( ) AND –2V AS
INNER PLANES.
C1
0.1F
C2
0.1F
+VS
50
50
50
JP1
1
TP GND
JP2
1 +VS
TP
JP3
1 –VS
TP
+ C4
1F
C7
1F
C6
1F
THERM
TVCC
HQG1
TH +VS
VH
VL
U3
AD53040
DATA
INH –VS
C19
0.1F
R7
50
C16
0.039F
IL+
G2H
VOUT
G2L
IL–
J8
SIDESMB
C18 TEST_LD
5pF
50
J7
SIDESMB
VOUT
C17
0.039F
PWR
GND
C3
0.1F
VLOW
–2V
VHIGH
–VS
VEE
–5.2V
–VS
THERM
–5.2V
C9
0.1F
C10
0.1F
C11
0.1F
VCC
+VS
C5 C8
1F 0.1F
GND
DB15
Figure 3. Evaluation Board Schematic
–6– REV. B

6 Page



ページ 合計 : 7 ページ
 
PDF
ダウンロード
[ AD53040 データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
AD5304

2.5 V to 5.5 V/ 500 uA/ Quad Voltage Output 8-/10-/12-Bit DACs in 10-Lead microSOIC

Analog Devices
Analog Devices
AD53040

Ultrahigh Speed Pin Driver

Analog Devices
Analog Devices
AD53041

High Speed Active Load

Analog Devices
Analog Devices
AD53042

High Speed Window Comparator

Analog Devices
Analog Devices


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap