DataSheet.jp

ADM8830ACP の電気的特性と機能

ADM8830ACPのメーカーはAnalog Devicesです、この部品の機能は「Charge Pump Regulator for Color TFT Panel」です。


製品の詳細 ( Datasheet PDF )

部品番号 ADM8830ACP
部品説明 Charge Pump Regulator for Color TFT Panel
メーカ Analog Devices
ロゴ Analog Devices ロゴ 




このページの下部にプレビューとADM8830ACPダウンロード(pdfファイル)リンクがあります。

Total 8 pages

No Preview Available !

ADM8830ACP Datasheet, ADM8830ACP PDF,ピン配置, 機能
FEATURES
3 Output Voltages (+5.1 V, +15.3 V, –10.2 V) from
One 3 V Input Supply
Power Efficiency Optimized for Use with TFT in
Mobile Phones
Low Quiescent Current
Low Shutdown Current (<1 A)
Fast Transient Response
Shutdown Function
Power Saving during Blanking Period
Option to Use External LDO
APPLICATIONS
Handheld Instruments
TFT LCD Panels
Cellular Phones
GENERAL DESCRIPTION
The ADM8830 is a charge pump regulator used for color thin
film transistor (TFT) liquid crystal displays (LCDs). Using
charge pump technology, the device can be used to generate three
output voltages (+5.1 V ± 2%, +15.3 V, –10.2 V) from a single
3 V input supply. These outputs are then used to provide
supplies for the LCD controller (5.1 V) and the gate drives for
the transistors in the panel (+15.3 V and –10.2 V). Only a few
external capacitors are needed for the charge pumps. An efficient
low dropout voltage regulator also ensures that the power
efficiency is high and provides a low ripple 5.1 V output. This
LDO can be shut down and an external LDO used to regulate
the 5 V doubler output and drive the input to the charge pump
section, which generates the +15.3 V and –10.2 V outputs if so
required by the user.
The ADM8830 has an internal 100 kHz oscillator for use in
scanning mode, but the part must be clocked by an external clock
source in blanking (low current) mode.The internal oscillator is
used to clock the charge pumps during scanning mode where the
current is highest. During blanking periods, the ADM8830
switches to use an external, lower frequency clock.This allows the
user to vary the frequency and maximize power efficiency during
blanking periods.The tolerances on the output voltages are
Charge Pump Regulator
for Color TFT Panel
ADM8830
FUNCTIONAL BLOCK DIAGRAM
CLKIN
SCAN/BLANK
LDO_ON/OFF
SHDN
VCC
ADM8830
C5
2.2F
VOLTAGE
DOUBLER
OSCILLATOR
CONTROL
LOGIC
LDO
VOLTAGE
REGULATOR
DOUBLE
TIMING
GENERATOR
TRIPLE
VOLTAGE
TRIPLER
SHUTDOWN
CONTROL
DISCHARGE
VOLTAGE
INVERTER
GND
C1+
C1–
C1
2.2F
VOUT
LDO IN
C6
2.2F
+5VOUT
+5VIN
C2+
C2
C2– 1F
C3+
C3
C3– 1F
+15VOUT
C4+
C4
C4– 1F
+5.1V
C7
2.2F
+15.3V
C8
1F
–10VOUT
–10.2V
C9
1F
seamlessly maintained when switching from scanning mode to
blanking mode or vice versa.
The ADM8830 has a number of power saving features, including
low power shutdown and reduced quiescent current consumption
during the blanking periods mentioned above. The 5.1 V output
consumes the most power, so power efficiency is also maximized
on this output with an oscillator enabling scheme (Green Idle™).
This effectively senses the load current that is flowing and turns
on the charge pump only when charge needs to be delivered to
the 5 V pump doubler output.
The ADM8830 is fabricated using CMOS technology for minimal
power consumption. The part is packaged in 20-lead LFCSP
and TSSOP packages.
REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
that may result from its use. No license is granted by implication or oth-
erwise under any patent or patent rights of Analog Devices.Trademarks
and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© 2003 Analog Devices, Inc. All rights reserved.

1 Page





ADM8830ACP pdf, ピン配列
TIMING SPECIFICATIONS (VCC = 2.6 V to 3.6 V, TA = –40C to +85C, unless otherwise noted, C1, C5, C6,
C7 = 2.2 F, C2, C3, C4, C8, C9 = 1 F, CLKIN = 1 kHz in blanking mode.)
Parameter
Min
POWER-UP SEQUENCE
+5 V Rise Time, tR5V
+15 V Rise Time, tR15V
–10 V Fall Time, tF10V
Delay between –10 V Fall
and +15 V, tDELAY
POWER-DOWN SEQUENCE
+5 V Fall Time, tF5V
+15 V Fall Time, tF15V
–10 V Rise Time, tR10V
Specifications are subject to change without notice.
Typ
300
8
12
3
75
40
40
Max
Unit
µs
ms
ms
ms
ms
ms
ms
Test Conditions
10% to 90%, Figure 2
10% to 90%, Figure 2
90% to 10%, Figure 2
Figure 2
90% to 10%, Figure 2
90% to 10%, Figure 2
10% to 90%, Figure 2
ADM8830
ABSOLUTE MAXIMUM RATINGS*
(TA = 25°C, unless otherwise noted.)
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +4.0 V
Input Voltage to Digital Inputs . . . . . . . . . . . . . –0.3 V to +4.0 V
Output Short Circuit Duration to GND . . . . . . . . . . . . . 10 sec
Output Voltage
+5.1 V Output . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +6 V
–10.2 V Output . . . . . . . . . . . . . . . . . . . . . . . .–12 V to +0.3 V
+15.3 V Output . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +17 V
Operating Temperature Range . . . . . . . . . . . . –40°C to +85°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.55 W
(Derate 33 mW/°C above 25°C)
Storage Temperature Range . . . . . . . . . . . . . –65°C to +150°C
ESD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class I
*This is a stress rating only; functional operation of the device at these or any other
conditions above those indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating conditions for extended periods
of time may affect reliability.
THERMAL CHARACTERISTICS
20-Lead TSSOP Package:
JA = 72°C/W
20-Lead LFCSP Package:
JA = 31°C/W
Model
ADM8830ACP
ADM8830ACP-REEL7
ADM8830ARU
ADM8830ARU-REEL
ADM8830ARU-REEL7
EVAL-ADM8830EB
ORDERING GUIDE
Temperature Range Package Description
–40ºC to +85ºC
–40ºC to +85ºC
–40ºC to +85ºC
–40ºC to +85ºC
–40ºC to +85ºC
Lead Frame Chip Scale Package
Lead Frame Chip Scale Package
Thin Shrink Small Outline Package
Thin Shrink Small Outline Package
Thin Shrink Small Outline Package
Evaluation Board
Package Option
CP-20-1
CP-20-1
RU-20
RU-20
RU-20
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000V readily accumulate
on the human body and test equipment and can discharge without detection. Although the ADM8830
features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high
energy electrostatic discharges.Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
REV. B
–3–


3Pages


ADM8830ACP 電子部品, 半導体
ADM8830
LOAD ENABLE
LOAD DISABLE
+15V OUTPUT
5V OUTPUT
TPC 10. 5 V OutputTransient
Response for Maximum Load
Current
+15V OUTPUT
–10V OUTPUT
5VOUT
TPC 13. +15 V and –10 V Outputs at
Power-Down (Unloaded)
5V OUTPUT
5VOUT
–10V OUTPUT
TPC 11. 5 V OutputTransient Response,
Load Disconnected
TPC 12. +15 V and –10 V Outputs at
Power-Up
20.1
20.0
19.9
19.8
19.7
19.6
19.5
19.4
–40 –20
0 20 40 60
TEMPERATURE – C
80
TPC 14. Power Dissipation overTem-
perature, VCC = 3.6 V, Scanning Mode
with All O/Ps at Maximum Load
–6– REV. B

6 Page



ページ 合計 : 8 ページ
 
PDF
ダウンロード
[ ADM8830ACP データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
ADM8830ACP

Charge Pump Regulator for Color TFT Panel

Analog Devices
Analog Devices
ADM8830ACP-REEL7

Charge Pump Regulator for Color TFT Panel

Analog Devices
Analog Devices


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap