DataSheet.jp

AT29LV256-20PC の電気的特性と機能

AT29LV256-20PCのメーカーはATMEL Corporationです、この部品の機能は「256K 32K x 8 3-volt Only CMOS Flash Memory」です。


製品の詳細 ( Datasheet PDF )

部品番号 AT29LV256-20PC
部品説明 256K 32K x 8 3-volt Only CMOS Flash Memory
メーカ ATMEL Corporation
ロゴ ATMEL Corporation ロゴ 




このページの下部にプレビューとAT29LV256-20PCダウンロード(pdfファイル)リンクがあります。
Total 10 pages

No Preview Available !

AT29LV256-20PC Datasheet, AT29LV256-20PC PDF,ピン配置, 機能
AT29LV256
Features
Single Supply Voltage, Range 3V to 3.6V
3-Volt-Only Read and Write Operation
Software Protected Programming
•• Low Power Dissipation
15 mA Active Current
20 µA CMOS Standby Current
Fast Read Access Time - 200 ns
•• Sector Program Operation
Single Cycle Reprogram (Erase and Program)
512 Sectors (64 bytes/sector)
Internal Address and Data Latches for 64-Bytes
Fast Sector Program Cycle Time - 20 ms Max.
Internal Program Control and Timer
DATA Polling for End of Program Detection
Typical Endurance > 10,000 Cycles
CMOS and TTL Compatible Inputs and Outputs
•• Commercial and Industrial Temperature Ranges
Description
The AT29LV256 is a 3-volt-only in-system Flash Programmable Erasable Read Only
Memory (PEROM). Its 256K of memory is organized as 32,768 words by 8 bits.
Manufactured with Atmel’s advanced nonvolatile CMOS technology, the device offers
access times to 200 ns with power dissipation of just 54 mW over the commercial
temperature range. When the device is deselected, the CMOS standby current is less
than 20 µA. The device endurance is such that any sector can typically be written to
in excess of 10,000 times.
(continued)
256K (32K x 8)
3-volt Only
CMOS Flash
Memory
Pin Configurations
Pin Name Function
A0 - A14 Addresses
CE Chip Enable
OE Output Enable
WE Write Enable
I/O0 - I/O7 Data Inputs/Outputs
NC No Connect
DC Don’t Connect
PLCC Top View
AT29LV256
TSOP Top View
Type 1
0563A
4-33

1 Page





AT29LV256-20PC pdf, ピン配列
AT29LV256
Device Operation (Continued)
sition of WE (or CE). A0 to A5 specify the byte address
within the sector. The bytes may be loaded in any order;
sequential loading is not required. Once a programming
operation has been initiated, and for the duration of tWC, a
read operation will effectively be a polling operation.
HARDWARE DATA PROTECTION: Hardware features
protect against inadvertent programs to the AT29LV256 in
the following ways: (a) VCC sense— if VCC is below 1.8V
(typical), the program function is inhibited. (b) VCC power
on delay— once VCC has reached the VCC sense level,
the device will automatically time out 10 ms (typical) be-
fore programming. (c) Program inhibit— holding any one
of OE low, CE high or WE high inhibits program cycles. (d)
Noise filter— pulses of less than 15 ns (typical) on the WE
or CE inputs will not initiate a program cycle.
INPUT LEVELS: While operating with a 3.3V ±10%
power supply, the address inputs and control inputs (OE,
CE and WE) may be driven from 0 to 5.5V without ad-
versely affecting the operation of the device. The I/O lines
can only be driven from 0 to 3.6 volts.
PRODUCT IDENTIFICATION: The product identifica-
tion mode identifies the device and manufacturer as At-
mel. It may be accessed by hardware or software opera-
tion. The hardware operation mode can be used by an ex-
ternal programmer to identify the correct programming al-
gorithm for the Atmel product. In addition, users may wish
to use the software product identification mode to identify
the part (i.e. using the device code), and have the system
software use the appropriate sector size for program op-
erations. In this manner, the user can have a common
board design for 256K to 4-megabit densities and, with
each density’s sector size in a memory map, have the sys-
tem software apply the appropriate sector size.
For details, see Operating Modes (for hardware operation)
or Software Product Identification. The manufacturer and
device code is the same for both modes.
DATA POLLING: The AT29LV256 features DATA poll-
ing to indicate the end of a program cycle. During a pro-
gram cycle an attempted read of the last byte loaded will
result in the complement of the loaded data on I/O7. Once
the program cycle has been completed, true data is valid
on all outputs and the next cycle may begin. DATA polling
may begin at any time during the program cycle.
TOGGLE BIT: I n a d d i t i o n t o DATA p o l l i n g t h e
AT29LV256 provides another method for determining the
end of a program or erase cycle. During a program or
erase operation, successive attempts to read data from
the device will result in I/O6 toggling between one and
zero. Once the program cycle has completed, I/O6 will
stop toggling and valid data will be read. Examining the
toggle bit may begin at any time during a program cycle.
OPTIONAL CHIP ERASE MODE: The entire device
can be erased by using a 6-byte software code. Please
see Software Chip Erase application note for details.
Absolute Maximum Ratings*
Temperature Under Bias................. -55°C to +125°C
Storage Temperature...................... -65°C to +150°C
All Input Voltages
(including NC Pins)
with Respect to Ground ................... -0.6V to +6.25V
All Output Voltages
with Respect to Ground .............-0.6V to VCC + 0.6V
Voltage on A9
(including NC Pins)
with Respect to Ground ................... -0.6V to +13.5V
*NOTICE: Stresses beyond those listed under “Absolute Maxi-
mum Ratings” may cause permanent damage to the device.
This is a stress rating only and functional operation of the
device at these or any other conditions beyond those indi-
cated in the operational sections of this specification is not
implied. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
4-35


3Pages


AT29LV256-20PC 電子部品, 半導体
AC Byte Load Characteristics
Symbol
tAS, tOES
tAH
tCS
tCH
tWP
tDS
tDH, tOEH
tWPH
Parameter
Address, OE Set-up Time
Address Hold Time
Chip Select Set-up Time
Chip Select Hold Time
Write Pulse Width (WE or CE)
Data Set-up Time
Data, OE Hold Time
Write Pulse Width High
AC Byte Load Waveforms (1, 2)
WE Controlled
Min
10
100
0
0
200
100
10
200
Max Units
ns
ns
ns
ns
ns
ns
ns
ns
CE Controlled
4-38 AT29LV256

6 Page



ページ 合計 : 10 ページ
 
PDF
ダウンロード
[ AT29LV256-20PC データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
AT29LV256-20PC

256K 32K x 8 3-volt Only CMOS Flash Memory

ATMEL Corporation
ATMEL Corporation
AT29LV256-20PI

256K 32K x 8 3-volt Only CMOS Flash Memory

ATMEL Corporation
ATMEL Corporation


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap