|
|
PDF BH162827ADL Data sheet ( Hoja de datos )
| Número de pieza | BH162827ADL | |
| Descripción | 20-bit buffer/line driver/ non-inverting/with 30ohm termination resistors (3-State) | |
| Fabricantes | NXP Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de BH162827ADL (archivo pdf) en la parte inferior de esta página. Total 11 Páginas | ||
|
No Preview Available !
INTEGRATED CIRCUITS
74ABT162827A
74ABTH162827A
20-bit buffer/line driver, non-inverting,
with 30W termination resistors (3-State)
Product specification
Supersedes data of 1997 Feb 26
IC23 Data Handbook
1998 Feb 27
Philips
Semiconductors
1 page  
Philips Semiconductors
20-bit buffer/line driver, non-inverting,
with 30W termination resistors (3-State)
Product specification
74ABT162827A
74ABTH162827A
RECOMMENDED OPERATING CONDITIONS
SYMBOL
PARAMETER
VCC
VI
VIH
VIL
IOH
IOL
∆t/∆v
Tamb
DC supply voltage
Input voltage
High-level input voltage
Low-level Input voltage
High-level output current
Low-level output current
Input transition rise or fall rate
Operating free-air temperature range
LIMITS
MIN MAX
4.5 5.5
0 VCC
2.0
0.8
–32
12
0 10
–40 +85
UNIT
V
V
V
V
mA
mA
ns/V
°C
DC ELECTRICAL CHARACTERISTICS
LIMITS
SYMBOL
PARAMETER
TEST CONDITIONS
Tamb = +25°C
Tamb = -40°C
to +85°C
UNIT
MIN TYP MAX MIN MAX
VIK Input clamp voltage
VCC = 4.5V; IIK = -18mA
–0.9 –1.2
–1.2 V
VCC = 4.5V; IOH = -3mA; VI = VIL or VIH
2.5 3.1
2.5
V
VOH
High-level output voltage
VCC = 5.0V; IOH = -3mA; VI = VIL or VIH
3.0 3.6
3.0
V
VCC = 4.5V; IOH = -32mA; VI = VIL or VIH
2.0 2.7
2.0
V
VOL
Low-level output voltage
VCC = 4.5V; IOH = 8mA; Vl = VIL or VIN
VCC = 4.5V; IOL = 12mA; VI = VIL
0.65 0.65 V
0.80 0.80 V
II Input leakage current
VCC = 5.5V; VI = GND or 5.5V
±0.01 ±1.0
±1.0 µA
VCC = 5.5V; VI = 5.5V
0.01 1
1 µA
II
Input leakage current
74ABTH162827A
VCC = 5.5V; VI = VCC or GND
VCC = 5.5V; VI = VCC
VCC = 5.5V; VI = 0
Control
pins
Data pins4
±0.01
0.01
–1
±1
1
–3
±1 µA
1 µA
–5 µA
IHOLD
Bus Hold current A inputs5
74ABTH162827A
VCC = 4.5V; VI = 0.8V
VCC = 4.5V; VI = 2.0V
VCC = 5.5V; VI = 0 to 5.5V
35
–75
±800
35
–75 µA
IOFF Power-off leakage current VCC = 0.0V; VO = 4.5V; VI = 0V or 5.5V
±5.0 ±100
±100 µA
IPU/IPD
Power-up/down 3-State
output current3
VCC = 2.1V; VO = 0.5V; VI = GND or VCC;
V OE = Don’t care
±5.0 ±50
±50 µA
IOZH 3-State output High current VCC = 5.5V; VO = 2.7V; VI = VIL or VIH
1.0 10
10 µA
IOZL 3-State output Low current VCC = 5.5V; VO = 0.5V; VI = VIL or VIH
–1.0 –10
–10 µA
ICEX
Output High leakage
current
VCC = 5.5V; VO = 5.5V; VI = GND or VCC
1.0 50
50 µA
IO Output current1
VCC = 5.5V; VO = 2.5V
–50 –70 –180 –50 –180 mA
ICCH
VCC = 5.5V; Outputs High, VI = GND or
VCC
0.5 1
1 mA
ICCL Quiescent supply current VCC = 5.5V; Outputs Low, VI = GND or VCC
9 19
19 mA
ICCZ
VCC = 5.5V; Outputs 3-State;
VI = GND or VCC
0.5 1
1 mA
∆ICC
Additional supply current
per input pin2
VCC = 5.5V; one input at 3.4V,
other inputs at VCC or GND
0.2 1
1 mA
NOTES:
1. Not more than one output should be tested at a time, and the duration of the test should not exceed one second.
2. This is the increase in supply current for each input at 3.4V.
3. This parameter is valid for any VCC between 0V and 2.1V with a transition time of up to 10msec. From VCC = 2.1V to VCC = 5V ± 10% a
transition time of up to 100µsec is permitted.
4. Unused pins at VCC or GND.
5. This is the bus hold overdrive current required to force the input to the opposite logic state.
1998 Feb 27
5
5 Page 
Philips Semiconductors
20-bit buffer/line driver, non-inverting, with 30W
termination resistors (3-State)
Product specification
74ABT162827A
74ABTH162827A
Data sheet status
Data sheet
status
Product
status
Definition [1]
Objective
specification
Development
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
Preliminary
specification
Qualification
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make chages at any time without notice in order to
improve design and supply the best possible product.
Product
specification
Production
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
© Copyright Philips Electronics North America Corporation 1998
All rights reserved. Printed in U.S.A.
print code
Document order number:
Date of release: 05-96
9397-750-03505
Philips
Semiconductors
yyyy mmm dd
11
11 Page | ||
| Páginas | Total 11 Páginas | |
| PDF Descargar | [ Datasheet BH162827ADL.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| BH162827ADGG | 20-bit buffer/line driver/ non-inverting/with 30ohm termination resistors (3-State) | NXP Semiconductors |
| BH162827ADGG | 20-bit buffer/line driver/ non-inverting/with 30ohm termination resistors (3-State) | NXP Semiconductors |
| BH162827ADL | 20-bit buffer/line driver/ non-inverting/with 30ohm termination resistors (3-State) | NXP Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |