|
|
PDF IXDP631PI Data sheet ( Hoja de datos )
| Número de pieza | IXDP631PI | |
| Descripción | Inverter Interface and Digital Deadtime Generator | |
| Fabricantes | IXYS | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de IXDP631PI (archivo pdf) en la parte inferior de esta página. Total 7 Páginas | ||
|
No Preview Available !
Inverter Interface and Digital Deadtime Generator
for 3-Phase PWM Controls
Type
IXDP630 PI
IXDP631 PI
Package
18-Pin Plastic DIP
18-Pin Plastic DIP
Configuration
RC Oscillator
Crystal Oscillator
Temp. Range
-40°C to +85°C
-40°C to +85°C
This 5 V HCMOS integrated circuit is
intended primarily for application in
three-phase, sinusoidally commutated
brushless motor, induction motor, AC
servomotor or UPS PWM modulator
control systems. It injects the required
deadtime to convert a single phase leg
PWM command into the two separate
logic signals required to drive the upper
and lower semiconductor switches in a
PWM inverter. It also provides facilities
for output disable and fast overcurrent
and fault condition shutdown.
In the IXDP630, deadtime programming
is achieved by an internal RC oscillator.
In the IXDP631, programming is
achieved by use of a crystal oscillator.
An alternative for both the IXDP630/
631 is with an external clock signal.
Because of its flexibility, the IXDP630/
631 is easily utilized in a variety of
brushed DC, trapezoidally commutated
brushless DC, hybrid and variable
reluctance step and other more exotic
PWM motor drive power and control
circuit designs.
Block Diagram IXDP 630/IXDP 631
Features
l 5 V HCMOS logic implementation
maintains low power at high speed
l Schmitt trigger inputs and CMOS
logic levels improve noise immunity
l Simultaneously injects equal dead-
time in up to three output phases
l Replaces 10-12 standard SSI/MSI
logic devices
l Allows a wide range of PWM
modulation strategies
l Directly drives high speed
optocouplers
Applications
l 1- and 3- Phase Motion Controls
l 1- and 3- Phase UPS Systems
l General Power Conversion Circuits
l Pulse Timing and Waveform
Generation
l General Purpose Delay and Filter
l General Purpose Three Channel
"One Shot"
IXYS reserves the right to change limits, test conditions and dimensions.
I - 14
© 1998 IXYS All rights reserved
1 page  
IXDP630
IXDP631
Selecting Components for a Specific
Requirement
Deadtime in the IXDP630/631 is exactly
8 clock periods: DT= 8/fclk. Once the
worst case (minimum) deadtime has
been determined (from Power switching
component manufacturer data sheets,
drive circuit analysis, breadboard
measurements, etc.) the clock
frequency is calculated: fclk(max) =
8/ DT(min).
This is the highest allowable clock
frequency, including the effects of initial
accuracy, tolerance, temperature coeffi-
cient, etc. When choosing oscillator
components, special attention to
resistor and capacitor construction is
mandatory.
Oscillator Design
There are two versions of the deadtime
generator. They have distinctly different
internal oscillator designs to serve
different application. In either case,
however, the internal oscillator can be
disabled by simply leaving its external
components off. An HCMOS compatible
clock up to 24 MHz can be fed directly
into the RCIN or XTLIN pin.
IXDP630 RC Oscillator Design
The IXDP630 uses a Schmitt trigger
inverter oscillator (Fig. 3). Two external
components, ROSC and COSC, determine
the clock frequency and consequently
the deadtime. This design allows a
significant cost reduction over a
standard crystal oscillator, but entails a
trade-off in frequency accuracy. The
initial accuracy and drift are a function
of the external component tolerance
and temperature coefficients, supply
voltage, and IXDP630 internal para-
meters. At frequencies under 1 MHz,
assuming the external components
were perfect, the IXDP630 would
introduce an initial accuracy error of
5 %, and a temperature dependence of
-400 ppm. The shift in frequency over
the VCC range 4.5 V to 5.5 V is typically
less than 5 %.
At higher frequencies and with resistor
values below 1 kΩ, the IXDP630
internal parameters become more
influential factors. This results in
greater frequency variation from one
device to another, as well as with
temperature and supply voltage
variations. If high accuracy is a
requirement, the IXDP631 with a crystal
oscillator would be the better choice.
Oscillator frequency vs. Rosc and Cosc
is shown in Fig. 4. For an analytical
method of setting the oscillator, the
design equation is for operation below
1 MHz approximately:
fOSC ≈
0.95
Cosc Rosc
For operation above 1 MHz,
0.95
fOSC ≈
Cosc (Rosc+30) + 3 10-8
IXDP631 Precision Crystal Oscillator
Design
The IXDP631 uses a more common
standard internal crystal oscillator
design. For proper operation the crys-
tal must be of the parallel resonant
type, resonating at the crystal's funda-
mental frequency. Fig. 5 illustrates the
recommended oscillator configuration.
Note the external components required.
The capacitors are needed to achieve
the calibrated crystal frequency (their
value is determined by the crystal
manufacturer), and the resistor is
necessary to assure that the circuit
starts in every case. While the circuit
will usually operate without these extra
parts, this is not recommended.
The crystal oscillator in the IXDP631 is
significantly more accurate than the RC
oscillator in the IXDP630. The total
tolerance (including effects of initial
accuracy, temperature, supply voltage,
drift, etc.) is better than ±100 ppm. This
improves the accuracy and repeatability
of the desired deadtime, but at the
added expense of a crystal.
Which version is appropriate for your
application? That depends on how you
are willing to trade off component cost
for deadtime accuracy.
COSC = 470 pF
COSC = 270 pF
COSC = 100 pF
COSC = 47 pF
COSC = 1 nF
COSC = 2.2 nF
COSC = 4.7 nF
COSC = 10 nF
Fig. 3: IXDP630 internal Schmitt Trigger
inverter oscillator (ROSC, COSC are
external)
0.1 1 10 100 1000
Oscillator - kHz
Fig. 4. Oscillator frequency component selection for IXDP630.
10 000
I - 18
© 1998 IXYS All rights reserved
5 Page | ||
| Páginas | Total 7 Páginas | |
| PDF Descargar | [ Datasheet IXDP631PI.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| IXDP631PI | Inverter Interface and Digital Deadtime Generator | IXYS |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |