DataSheet.jp


Datasheet E1205D-1W PDF ( 特性, スペック, ピン接続図 )

部品番号 E1205D-1W
部品説明 DC/DC Converter
メーカ YUAN
ロゴ YUAN ロゴ 
プレビュー
Total 4 pages
		
11

No Preview Available !

E1205D-1W Datasheet, E1205D-1W PDF,ピン配置, 機能
SHENZHEN SUNYUAN TECHNOLOGY CO., LTD.
EXXXXD/S-1W SERIES DC-DC CONVERTER
www.DataSheet4U.com
z RATED 1W OUTPUT
z HIGH POWER DENSITY
z 7PIN SIP /14PIN DIP PACKAGE
z DUAL OUTPUT
z INDUSTRIAL STANDARD PIN-OUT
z NO HEAT SINK REQUIRED
z 3KVAC ISOLATION
z FIXED INPUT
z UNREGULATED OUTPUT
z PCB MOUNTING
ELECTRICAL SPECIFICATIONS
All specifications tested typically @ 25°C, humidity<75%, nominal input and rated output unless otherwise noted.
OUTPUT SPECIFICATIONS
Items:
Testing condition
Output accuracy:
At full load and nominal Vin
Output power:
Line regulation:
Load regulation:
Ripple and noise:
Temperature drift:
Minimum load
Switching frequency
Over load protection
Short circuit protection
For Vin change of 1%
From 20% to full load
20MHz bandwidth
% of FL at nominal input
Min
0.1W
Typ
1W
10%
100KHz
120
Momentary
Max
±5%
1W
1.2
15%
150 mV p-p
±0.02 %/°C
10%
INPUT SPECIFICATIONS
Items:
Testing condition
3.3 VDC nominal input
Input voltage range
5 VDC nominal input
9 VDC nominal input
12VDC nominal input
15 VDC nominal input
24VDC nominal input
Min
Typ
3-3.6
4.5-5.5
8.1-9.9
10.8-13.2
13.5-16.5
21.6-26.4
Max
Copyright @ Shenzhen Sunyuan Technology Co., Ltd.
Edition-SZSY-07-01
Printed in P.R.C January 2007 Page 1 of 4

1 Page



E1205D-1W pdf, ピン配列
SHENZHEN SUNYUAN TECHNOLOGY CO., LTD.
EXXXXD/S-1W SERIES DC-DC CONVERTER
CONNECTING DC-DC CONVERTERS IN SERIES
www.DataSheet4U.com
Galvanic isolation of the output allows multiple converters to be connected in series simply by connecting the positive output of one converter to the
negative of another (see figure 1). In this way, non-standard voltage rails can be generated, however, the current output of the highest output voltage
converter should not be exceeded. When converters are connected in series, additional filtering is strongly recommended as the converters switching
circuits are not synchronized. As well as a summation of the ripple voltages, the output could also produce relatively large beat frequencies. A
capacitor across the output will help, as will a series inductor.
CONNECTING DC-DC CONVERTERS IN PARALLEL
If the available power output from a single converter is inadequate for the application, then multiple converters can be paralleled to produce a higher
output power. However, it is not recommended to parallel converters to generate a higher power output, please select our higher power output
modules or contact us for a customized solution.
It should be noted that it is always preferable to parallel multiple converters of the same type. For instance, if a 2.5W converter is required, then either
2pcs AxxxxS-2W should be used or 3 AxxxxS-1W, not an AxxxxS-2W and an AxxxxS-1W. The reason for this is that the output voltages are not
sufficiently well matched to guarantee that an AxxxxS-2W would supply twice as much as an AxxxxS-1W and the situation would occur where there
was only 1W being drawn from the AxxxxS-2W and 1.5W from AxxxxS-1W. Even with paralleled converters of the same type, loading will be
uneven, however, there is only likely to be around a 10% difference in output load when the output voltages are well matched.
When connecting converter outputs, it should be remembered that the switching will not be synchronous, hence some form of coupling should be
employed. One possible solution is to use a diode feed, this is suitable mainly for 12V and 15V output types only where the diode voltage drop
(typically 0.6V) will not significantly affect the circuit functionality (see figure 2). With 5V and 9V supplies the diode drop is generally too large to
consider as a suitable means of connecting paralleled converters. This method also has a beat frequency that will superimpose itself over the ripple of
the two converters, this can be reduced by using an external capacitor at the paralleled output. The preferred method of connecting converters in
parallel is via series inductors on the output (see figure 3). This configuration not only has a lower loss of voltage than the diode method, but by
suitable choice of inductor and an additional external capacitor, the beat frequency can be significantly reduced, as will the ripple from each converter.
Suitable values are given in the table below (see table 1), these typically reduce the beat and ripple frequencies by a factor of 10.
ISOLATION
One of the main features of the majority of Sunyuan components DC-DC converters is the high galvanic isolation capability. This allows several
variations on circuit topography by using a single DC-DC converter. The basic input to output isolation can be used to provide either a simple isolated
output power source, or to generate different voltage rails and /or dual polarity rails. These configurations are most often found in data processing,
instrumentation and other noise sensitive circuits where it is necessary to isolate the load and noise presented to the local power supply rails from that
of an entire system. Usually local supply noise appears as common mode noise at the converter and does not pollute the main system power supply
rails. The isolated positive output can be connected to the input ground rail to generate a negative supply rail if required. Since the output is isolated
from the input the choice of reference for the output side can be relatively arbitrary, for example an additional single rail can be generated above the
main supply rail or offset by some other DC value.
Regulated converters need more consideration than the unregulated type for mixing the reference level. Essentially the single supply rail has a
regulator in its positive output rail only, hence referring the isolated ground will only work if all the current return is through the DC-DC and not via
other external components, such as diode bias, resistor feed. Have an alternative return path can upset the regulation and the performance of the
system may not equal that of the converter. In one word, the isolation features are to generate two completely independent power supply but also
united perfectly through the modern technology. This has been widely used in the application of mixed circuits, A/D, D/A and other circuits that are
sensitive to noise.
FILTERING
All Sunyuan isolated DC-DC Converters have a fixed characteristic frequency at which the device operates. This fixed frequency allows filtering that
is relatively simple compared to pulse-skipping types. In a pulse-skipping converter a large range of frequencies are encountered as the device adjusts
the pulse interval for loading conditions.
Copyright @ Shenzhen Sunyuan Technology Co., Ltd.
Edition-SZSY-07-01
Printed in P.R.C January 2007 Page 3 of 4


3Pages







ページ 合計 : 4 ページ
PDF
ダウンロード
[ E1205D-1W.PDF ]

共有リンク

Link :

おすすめデータシート

部品番号部品説明メーカ
E1205D-1W

There is a function of DC/DC Converter.

YUAN
YUAN

多くを見つけるデータシート

部品番号部品説明メーカ
82S129

The 82S126 and 82S129 are field programmable, which means that custom patterns are immediately available by following the Signetics Generic fusing procedure. 1K-bit TTL Bipolar PROM, Address access time : 50ns max.

NXP
NXP
D1695

This part is a darlington connection NPN silicon epitaxial transistor. The 2SD1695 is a Darlington connection transistor and incorporates a dumper diode between the collector and emitter and a constant voltage diode and protection elements between the collector and base. This transistor is ideal for drives in solenoid and actuators.

NEC
NEC
FDMS86368

N-Channel Power Trench, 80V, 80A, 4.5mΩ.

Fairchild
Fairchild
2SC2456

Here is a Color TV Horizontal Driver, Vceo=300V, TO-126 Package.

Toshiba
Toshiba

www.DataSheet.jp    |   2018   |  メール    |   最新    |   Sitemap