|
|
PDF STK5F4U3C2D-E Data sheet ( Hoja de datos )
| Número de pieza | STK5F4U3C2D-E | |
| Descripción | Intelligent Power Module | |
| Fabricantes | ON Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de STK5F4U3C2D-E (archivo pdf) en la parte inferior de esta página. Total 14 Páginas | ||
|
No Preview Available !
STK5F4U3C2D-E
Intelligent Power Module (IPM)
600 V, 30 A
Overview
This “Inverter Power IPM” is highly integrated device containing all High
Voltage (HV) control from HV-DC to 3-phase outputs in a single DIP module
(Dual-In line Package). Output stage uses IGBT / FRD technology and
implements Under Voltage Protection (UVP) and Over Current Protection
(OCP) with a Fault Detection output flag. Internal Boost diodes are provided
for high side gate boost drive.
www.onsemi.com
Function
Single control power supply due to Internal bootstrap circuit for high side
pre-driver circuit
All control inputs and status outputs are at low voltage levels directly
compatible with microcontrollers.
A single power supply drive is enabled through the use of bootstrap circuits
for upper power supplies
Built-in dead-time for shoot-thru protection
Having open emitter output for low side IGBTs ; individual shunt resistor
per phase for OCP
Externally accessible embedded thermistor for substrate temperature
measurement
Shutdown function ‘ITRIP’ to disable all operations of the 6 phase output
stage by external input
Certification
UL1557 (File number : E339285)
Specifications
Absolute Maximum Ratings at Tc = 25C
Parameter
Symbol
Remarks
Ratings
Supply voltage
Collector-emitter voltage
VCC
VCE
P to NU, NV, NW, surge < 500 V *1
P to U, V, W, U to NU, V to NV, or W to NW
450
600
Output current
Io
P, NU, NV, NW, U, V, W terminal current
P, NU, NV, NW, U, V, W terminal current, Tc = 100C
±30
±15
Output peak current
Iop P, NU, NV, NW, U, V, W terminal current, PW = 1 ms
±45
Pre-driver supply voltage
Input signal voltage
FAULT terminal voltage
VD1, 2, 3, 4
VIN
VFAULT
VB1 to VS1, VB2 to VS2, VB3 to VS3, VDD to VSS *2
HIN1, 2, 3, LIN1, 2, 3, terminal
FAULT terminal.
20
0.3 to VDD
0.3 to VDD
Maximum loss
Pd IGBT per channel
56.8
Junction temperature
Tj IGBT, FRD
150
Storage temperature
Tstg
40 to +125
Operating temperature
Tc IPM case
20 to +100
Tightening torque
MT A screw part at use M4 type screw *3
1.17
Withstand Voltage
Vis 50 Hz sine wave AC 1 minute *4
2000
Reference voltage is “VSS” terminal voltage unless otherwise specified.
*1 : Surge voltage developed by the switching operation due to the wiring inductance between the P and N terminals.
*2 : Terminal voltage : VD1 = VB1 to VS1, VD2 = VB2 to VS2, VD3 = VB3 to VS3, VD4 = VDD to VSS.
*3 : Flatness of the heat-sink should be 0.25 mm and below.
*4 : Test conditions : AC 2500 V, 1 s.
Unit
V
V
A
A
V
V
V
W
C
C
C
Nm
VRMS
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed,
damage may occur and reliability may be affected.
ORDERING INFORMATION
See detailed ordering and shipping information on page 14 of this data sheet.
© Semiconductor Components Industries, LLC, 2016
October 2016 - Rev. 1
1
Publication Order Number :
STK5F4U3C2D-E/D
1 page  
STK5F4U3C2D-E
Test Circuit
(The tested phase : U+ shows the upper side of the U phase and U shows the lower side of the U phase)
ICE / IR(BD)
U V W NU NV NW
M 42 42 42 38 34 30
N 38 34 30 27 25 23
U(BD)
M1
N 19
V(BD)
4
19
W(BD)
7
19
VD1=15V
VD2=15V
VD3=15V
VD4=15V
1M
2
4
5
7
8
18
19,20
N
Fig.1
ICE
A
VCE
VCE(sat) (Test by pulse)
U V W NU NV NW
M 42 42 42 38 34 30
N 38 34 30 27 25 23
m 10 11 12 13 14 15
VF (Test by pulse)
U
M 42
N 38
V
42
34
W NU NV NW
42 38 34 30
30 27 25 23
VD1=15V
VD2=15V
VD3=15V
VD4=15V
5V
1
2
4
5
7
8
18
m
19,20
M
V
VCE(SAT)
N
Fig.2
Ic
M
V VF
N
Fig.3
IF
ID
VD1 VD2 VD3
M1 4 7
N2 5 8
VD4
18
19
ID
AM
VD*
N
Fig.4
www.onsemi.com
5
5 Page 
Io-f curve
STK5F4U3C2D-E
Motor Current vs. Frequency
(Sine wave oparation,Vcc = 300 V, Tj = 150°C,ON Duty=96%)
50
40
30
20
10
0
0 5 10 15
Switching Frequency : fc (kHz)
20
Fig.12 Maximum sinusoidal phase current as function of switching frequency
at Tc = 100C, VCC = 300 V
Switching waveform
Turn on
Fig. 13 IGBT Turn-on. Typical turn-on waveform Tc = 100C, VCC = 300 V, Ic = 15 A
Turn off
Fig. 14 IGBT Turn-off. Typical turn-off waveform at Tc = 100C, VCC = 300 V, Ic = 15 A
www.onsemi.com
11
11 Page | ||
| Páginas | Total 14 Páginas | |
| PDF Descargar | [ Datasheet STK5F4U3C2D-E.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| STK5F4U3C2D-E | Intelligent Power Module | ON Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |