DataSheet.jp

DT018ATFT の電気的特性と機能

DT018ATFTのメーカーはDisplaytechです、この部品の機能は「LCD Module」です。


製品の詳細 ( Datasheet PDF )

部品番号 DT018ATFT
部品説明 LCD Module
メーカ Displaytech
ロゴ Displaytech ロゴ 




このページの下部にプレビューとDT018ATFTダウンロード(pdfファイル)リンクがあります。

Total 12 pages

No Preview Available !

DT018ATFT Datasheet, DT018ATFT PDF,ピン配置, 機能
Website: www.displaytech.com.hk
LCD Module
Product Specification
Product: DT018ATFT
1.8'' TFT Display Module (128RGBx160DOTS)
Contents in this document are subject to change without notice. No part of this document
may be reproduced or transmitted in any form or by any means, electronic or mechanical,
for any purpose, without the express written permission of Displaytech Ltd.
8 March 2011.

1 Page





DT018ATFT pdf, ピン配列
Displaytech Ltd LCD MODULE
DT018ATFT
Table of Content
Version: 1.0
1. REVISION RECORD .......................................................................... 1
2. Introduction .......................................................................................... 3
3. General Specifications .......................................................................... 3
4. Mechanical Drawing............................................................................. 4
5. Interface Description ............................................................................ 5
6. Absolute Maximum Ratings ................................................................ 7
7. Electrical Characteristics..................................................................... 7
8. Display Controller /Power Supply Timing ......................................... 7
9. Backlight specification ......................................................................... 8
10. Optical Characteristics......................................................................... 8
11. Safety Precaution ................................................................................ 11
2


3Pages


DT018ATFT 電子部品, 半導体
Displaytech Ltd LCD MODULE
DT018ATFT
5. Interface Description
Pin no
1
2
3
Symbol
LEDA
LED K1
LED K2
I/O Description
--- Backlight anode.
--- Backlight cathode K1
--- Backlight cathode K2
MCU parallel interface type selection
4 IM0
I
5 IM1
Version: 1.0
MCU Parallel interface bus and Serial interface select
6 IM2 I - IM2 = ‘1’; Parallel Interface
- IM2 = ‘0’; Serial Interface
RGB and MCU interface mode selection pin
7
RCM0
I
8
RCM1
I
When RCM1, RCM0=‘1X’(RGB I/F), serial input/output signal in serial I/F mode.
The data is input on the rising edge of the SCL signal. The data is output on the
9
SDA
I
falling edge of the SCL signal.
When RCM1, RCM0=‘0X’(MCU I/F), this pin is not used, and fix at VDDI or
GND level.
If not used, please fix this pin at VDDI or GND level.
10
VCC
--- Power supply 2.8V
11 GND / VSS --- Power ground 0V
Read enable in 8080-parallel interface and Read/ Write operation enable pin in
12
RD
I
6800-parallel interface.
In 8080-parallel interface, if not used, please connect this pin to VDDI.
In 6800-parallel interface, if not used, please connect this pin to VDDI or GND.
Display data / Command selection pin in parallel and SCL in 3-pin SPI interface.
13
RS
I
RS=‘1’: Display data.
RS=‘0’: Command data.
If not used, please connect this pin to GND.
When– RCM=‘0’ (MCU I/F), D[17:0] are used to MCU parallel interface data bus,
14~31 DB17~DB0 I/O and D0 is also the serial input/ output signal in SPI interface mode.
In serial interface, D[17:1] are not used and should be connected to ground.
Tearing effect output pin to synchronies MCU to frame writing, activated by S/W
32 TE O command. When this pin is not activated, this pin is low.
If not used, please open this pin.
Chip reset pin (“Low Active”).
33 RES I This signal low will reset the device and must be applied to properly initialize the
chip.
34
CS
I
Chip select input pin (“Low” enable).
This pin can be permanently fixed “Low” in MCU interface mode only.
Write enable in parallel interface.
WR: for 8080 MCU
35 WR I R/WX: for 6800 MCU
RS: for 4-wire SPI
If not used, please connect this pin to VDDI or GND.
5

6 Page



ページ 合計 : 12 ページ
 
PDF
ダウンロード
[ DT018ATFT データシート.PDF ]


データシートを活用すると、その部品の主な機能と仕様を詳しく理解できます。 ピン構成、電気的特性、動作パラメータ、性能を確認してください。


共有リンク

Link :


部品番号部品説明メーカ
DT018ATFT

LCD Module

Displaytech
Displaytech


www.DataSheet.jp    |   2020   |  メール    |   最新    |   Sitemap