|
|
Número de pieza | ISL54216 | |
Descripción | USB 2.0 High-Speed/UART Dual SP3T | |
Fabricantes | Intersil | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de ISL54216 (archivo pdf) en la parte inferior de esta página. Total 17 Páginas | ||
No Preview Available ! USB 2.0 High-Speed/UART Dual SP3T (Dual 3 to 1
Multiplexer)
ISL54216
The Intersil ISL54216 is a single supply dual SP3T
analog switch that operates from a single supply in the
range of 2.7V to 4.6V. It was designed to multiplex
between three different differential data sources,
allowing the multiplexing of USB 2.0 high speed and/or
UART data signals through a common headphone
connector in Personal Media Players and other portable
battery powered devices.
The switch channels have very low ON capacitance and
high bandwidth to pass USB high speed signals
(480Mbps) with minimal edge and phase distortion and
can swing rail-to-rail to pass UART and full-speed USB
signals.
The ISL54216 is available in a tiny 12 Ld 2.2mmx1.4mm
ultra-thin QFN and 12 Ld 3mmx3mm TQFN packages. It
operates over a temperature range of -40°C to +85°C.
Related Literature
• Technical Brief TB363 “Guidelines for Handling and
Processing Moisture Sensitive Surface Mount Devices
(SMDs)”
Features
• High Speed (480Mbps) and Full Speed (12Mbps)
Signaling Capability per USB 2.0 on All Ports
• UART Capability on All Ports
• COM Pins Allow Negative Swings to -2V
• Compatible with Wired-OR Connected GND
Referenced Audio Sources
• All Switches Open Mode
• Power OFF Protection
• COM Pins Overvoltage Tolerant to 5.5V
• Low ON Capacitance @ 240MHz . . . . . . . . . . . . 4pF
• -3dB Frequency . . . . . . . . . . . . . . . . . . . . 800MHz
• Single Supply Operation (VDD) . . . . . . . 2.7V to 4.6V
• Available 12 Ld µTQFN and 12 Ld TQFN Packages
• Compliant with USB 2.0 Short Circuit Requirements
Without Additional External Components
• Pb-Free (RoHS Compliant)
Applications*(see page 15)
• MP3 and Other Personal Media Players
• Cellular/Mobile Phone
• Readers
Application Block Diagram
USB
TRANSCEIVER
USB
TRANSCEIVER
UART
3D-
3D+
2D-
2D+
1D-
1D+
3.3V
VDD
ISL54216
LOGIC CONTROL
C0
4MΩ C1
µCONTROLLER
VBUS
COM -
COM +
GND
September 27, 2010
FN7701.0
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2010. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
1 page ISL54216
Electrical Specifications - 2.7V to 3.6V Supply Test Conditions: VDD = +3.0V, GND = 0V, VC0H, VC1H = 1.4V,
VC0L, VC1L= 0.5V, (Note 11), Unless Otherwise Specified. Boldface limits apply over the operating temperature range,
-40°C to +85°C. (Continued)
PARAMETER
TEST CONDITIONS
MIN
MAX
TEMP (Notes
(Notes
(°C) 12, 13) TYP 12, 13) UNITS
Total Jitter, tJ
VDD =3.0V, RL = 50Ω, CL = 10pF, tR = tF = 500ps at 25
480Mbps
- 210 -
ps
Rise/Fall Degradation
(Propagation Delay), tPD
VDD = 3.0V, RL = 45Ω, CL = 10pF, (see Figure 6)
Crosstalk
VDD = 3.0V, RL = 50Ω, f = 240MHz
OFF-Isolation
VDD = 3.0V, RL = 50Ω, f = 240MHz
-3dB Bandwidth
Signal = 0dBm, 0.2VDC offset, RL = 50Ω, CL = 5pF
OFF Capacitance, CXD+OFF,
CXD-OFF
f = 1MHz, VDD = 3.0V (see Figure 4)
COM ON Capacitance, CCOM-(ON), f = 1MHz, VDD = 3.0V (see Figure 4)
CCOM+(ON)
COM ON Capacitance, CCOM-(ON), f = 240MHz, VDD = 3.0V
CCOM+(ON)
POWER SUPPLY CHARACTERISTICS
25
25
25
25
25
25
25
- 250 -
- -36 -
- -32 -
- 800 -
-3-
-6-
-4-
ps
dB
dB
MHz
pF
pF
pF
Power Supply Range, VDD
Positive Supply Current, IDD
(ALL OFF Mode)
VDD = 3.6V, C1 = GND, C0 = GND
Full 2.7
4.6
25 - 6.5 8
Full -
- 15
V
µA
µA
Positive Supply Current, IDD
(USB1 Mode)
Positive Supply Current, IDD
(USB2 Mode)
VDD = 3.6V, C1 = GND, C0 = VDD
VDD = 3.6V, C1 = VDD, C0 = GND
25 - 6.5 8 µA
Full -
- 15
µA
25 - 6.5 8 µA
Full -
- 15
µA
Positive Supply Current, IDD
(USB3 Mode)
VDD = 3.6V, C0 = C1 = VDD
Power OFF COMx Current, ICOMx VDD = 0V, C0 = C1 = Float, COMx = 5.25V
Power OFF Logic Current, IC0, IC1 VDD = 0V, C0 = C1 = 5.25V
Power OFF D+/D- Current, IXD+, VDD = 0V, C0 = C1 = Float, XD- = XD+ = 5.25V
IXD-
DIGITAL INPUT CHARACTERISTICS
C0, C1 Voltage Low, VC0L, VC1L VDD = 2.7V to 3.6V
C0, C1 Voltage High, VC0H, VC1H VDD = 2.7V to 3.6V
C0, C1 Input Current, IC0L, IC1L VDD = 3.6V, C0 = C1 = 0V or Float
C0, C1 Input Current, IC0H, IC1H VDD = 3.6V, C0 = C1 = 3.6V
C0, C1 Pull-Down Resistor, RCx VDD = 3.6V, C0 = C1 = 3.6V, Measure current into C0
or C1 pin and calculate resistance value.
25
Full
25
25
25
Full
Full
Full
Full
Full
- 6.5 8
- - 15
- -1
- 11 -
-5-
- - 0.5
1.4 - 5.25
-50 6.2 50
-2 1.6
2
-4-
µA
µA
µA
µA
µA
V
V
nA
µA
MΩ
NOTES:
11. Vlogic = Input voltage to perform proper function.
12. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this
data sheet.
13. Parameters with MIN and/or MAX limits are 100% tested at +25°C, unless otherwise specified. Temperature limits established
by characterization and are not production tested.
14. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal
range.
15. Limits established by characterization and are not production tested.
16. rON matching between channels is calculated by subtracting the channel with the highest max rON value from the channel
with lowest max rON value, between 1D+ and 1D- or between 2D+ and 2D- or between 3D+ and 3D-.
5 FN7701.0
September 27, 2010
5 Page ISL54216
Typical Performance Curves TA = +25°C, Unless Otherwise Specified. (Continued)
VDD = 2.7V
USB NEAR END MASK
TIME SCALE (0.2ns/DIV)
FIGURE 11. EYE PATTERN: 480Mbps WITH USB SWITCHES IN THE SIGNAL PATH
11 FN7701.0
September 27, 2010
11 Page |
Páginas | Total 17 Páginas | |
PDF Descargar | [ Datasheet ISL54216.PDF ] |
Número de pieza | Descripción | Fabricantes |
ISL54210 | MP3/USB 2.0 High Speed Switch | Intersil |
ISL54211 | MP3/USB 2.0 High Speed Switch | Intersil |
ISL54212 | MP3/USB 2.0 High Speed Switch | Intersil Corporation |
ISL54213 | MP3/USB 2.0 High Speed Switch | Intersil |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |